Suzuki 2010 Grand Vitara Owner's Manual
  1. Manuals
  2. Brands
  3. Suzuki Manuals
  4. Automobile
  5. 2010 Grand Vitara
  6. Owner's manual

Suzuki 2010 Grand Vitara Owner's Manual

Suzuki 2010 grand vitara automobile owner's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

ENGLISH
SERVICE STATION INFORMATION
Fuel recommendation:
See page 1-1
Engine oil recommendation:
Engine oil with "Starburst" symbol
For further details, see "Engine Oil and Filter" in the
"INSPECTION AND MAINTENANCE" section.
art No. 99011-79K21-03E June, 2009
Suzuki Red: Magenta 100%, Yellow 100%
Suzuki Blue: Cyan 100%, Magenta 70%
takumi Blue: Cyan 100%, Black 85%
Black
Brake and clutch fluid:
DOT3
Automatic transmission fluid:
SUZUKI ATF 3317 or Mobil ATF 3309
Tire cold pressure:
See the "Tire Information Label" located on the
driver's door lock pillar.
rinted in Japan
14.5 mm
OWNER’S MANUAL
eep With Vehicle At All Times.
Contains Important Information
On Safety, Operation & Maintenance.
2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2010 Grand Vitara and is the answer not in the manual?

Questions and answers

brenda
April 22, 2025

Are there any lights that go on to see you change gears and also is it a fuse for the windsheild washer fluid work or is it manual motor burnt out

0

Related Manuals for Suzuki 2010 Grand Vitara

Summary of Contents for Suzuki 2010 Grand Vitara

  • Page 1 DOT3 Engine oil recommendation: Automatic transmission fluid: Engine oil with “Starburst” symbol SUZUKI ATF 3317 or Mobil ATF 3309 For further details, see “Engine Oil and Filter” in the Tire cold pressure: “INSPECTION AND MAINTENANCE” section. See the “Tire Information Label” located on the driver’s door lock pillar.
  • Page 2 NOTE: The illustrated model is one of the GRAND VITARA series. © 2009 All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Suzuki Motor Corporation. 79K21-03E...
  • Page 3 IF YOU HAVE ANY PROBLEMS WITH YOUR SUZUKI: Please review the New Vehicle Warranty Information booklet supplied with your SUZUKI. Should you have a question or problem regarding the warranty or service of your vehicle, please take the following action:...
  • Page 4 Indicates a potential hazard that ling in either the United States or Canada, could result in death or injury. you may wish to contact the Suzuki Cus- tomer Relations Department directly of the country in which you are temporarily oper- ating your vehicle.
  • Page 5 CB (Citizen’s Band) radios may cause electronic interfer- ence with your vehicle’s ignition sys- tem, resulting in vehicle performance problems. Consult your SUZUKI dealer or qualified service technician for advice on installing such mobile communication equipment. 79K21-03E...
  • Page 6 MEMO 79K21-03E...
  • Page 7 INTRODUCTION Thank you for choosing SUZUKI and welcome to our growing family. Your choice was a wise one; SUZUKI products are a great value that will give you years of driving pleasure. This Owner’s Manual was prepared to help you have a safe, enjoyable, and trouble-free experience with your SUZUKI. In it you will learn about the vehicle’s operation, its safety features and maintenance requirements.

  • Page 8: Service Station Guide

    SERVICE STATION GUIDE 1. Fuel (see section 1) 2. Engine hood (see section 5) 3. Tire changing tools (see section 8) 4. Engine oil dipstick <Yellow> (see section 7) 5. Automatic transmission fluid dipstick <Red> (see section 7) 6. Engine coolant (see section 7) 7.

  • Page 9: Table Of Contents

    TABLE OF CONTENTS FUEL RECOMMENDATION California Proposition 65 Warning BEFORE DRIVING WARNING OPERATING YOUR VEHICLE Engine exhaust, some of its constitu- ents, and certain product compo- DRIVING TIPS nents contain or emit chemicals known to the State of California to cause cancer and birth defects or OTHER CONTROLS AND EQUIPMENT other reproductive harm.

  • Page 10: Illustrated Table Of Contents

    ILLUSTRATED TABLE OF CONTENTS EXTERIOR EXAMPLE 1. Rear Window Wiper (P.2-81) 2. Engine Hood (P.5-63) 3. Windshield Wiper (P.2-79) 4. Roof Rails or Roof Rack Anchors (if equipped) (P.5-78) 5. Radio Antenna (P.5-8) 6. Spare Wheel (P.8-3) 7. Tailgate (P.2-3) 8.
  • Page 11 INTERIOR EXAMPLE 1. Interior Light (P.5-64, P.7-40) 2. Seat Belts (P.2-26) 3. Coat hooks (if equipped) (P.5-70) 4. Side Curtain Air Bags (P.2-46) 5. Sun Visor (P.5-64) 6. Overhead Console Box (if equipped) (P.5-71) 7. Spot Light (P.5-66, P.7-41) 8. Inside Rearview Mirror (P.2-17) 9.

  • Page 12: Instrument Panel

    ILLUSTRATED TABLE OF CONTENTS INSTRUMENT PANEL EXAMPLE 1. Power Window Controls (if equipped) (P.2-15) 2. Power Mirror Control (if equipped) (P.2-18) 3. Remote Audio Controls (if equipped) (P.5-56) 4. Front Air Bags (P.2-45) 5. Cruise Control (P.3-26) 6. Hazard Warning Switch (P.2-79) 7.
  • Page 13 INSTRUMENT PANEL EXAMPLE 1. Lighting Control Lever (P.2-75)/ Turn Signal Control Lever (P.2-78) 2. Instrument Cluster (P.2-54) 3. Windshield Wiper and Washer Lever (P.2-79)/Rear Window Wiper and Washer Switch (P.2-81) 4. Rear Window Defroster and Outside Rearview Mirrors Defroster Switch (if equipped) (P.2-82) 5.
  • Page 14 Do not remove the messages for any reason. If a label comes off or the messages become difficult to be read, have it corrected by your SUZUKI dealer. 1. Air bag warning labels (on both sun visors) 2. Rollover warning label 3.

  • Page 15: Fuel Recommendation

    FUEL RECOMMENDATION FUEL RECOMMENDATION Fuel Recommendation ... 1-1 65D394 79K21-03E...

  • Page 16: Fuel Recommendation

    (wood alcohol) may be suitable for use in NOTE: your vehicle if they contain cosolvents and To help clean the air, SUZUKI recom- corrosion inhibitors. Do NOT USE fuels mends you use the oxygenated fuels. containing more than 5% methanol under However, if you are not satisfied with the any circumstances.

  • Page 17: Before Driving

    BEFORE DRIVING BEFORE DRIVING Keys ... 2-1 Door Locks ... 2-1 Keyless Start System Remote Controller/Keyless Entry System Transmitter ... 2-4 Theft Deterrent Light ... 2-15 Windows ... 2-15 Mirrors ... 2-17 Front Seats ... 2-18 Rear Seats ... 2-22 Seat Belts and Child Restraint Systems ...

  • Page 18: Keys: 8

    Keys: 8 Spare Tire Nut Lock: 5 BEFORE DRIVING Keys EXAMPLE 54G489 Your vehicle comes with a pair of identical keys. Keep the spare key in a safe place. One key can open all of the locks on the vehicle. The key identification number is stamped on a metal tag provided with the keys.
  • Page 19 Door Locks: 3, 5, 8 To unlock a front door from outside the vehicle, insert the key and turn the top of the key toward the rear of the vehicle. UNLOCK LOCK 64J002 To lock a door from inside the vehicle, turn the lock knob forward.
  • Page 20 Door Locks: 3, 5, 8 BEFORE DRIVING (when using the power door locking switch) To lock or unlock all the doors simulta- neously, depress the front or rear of the switch respectively. NOTE: • If your vehicle is equipped with the key- less entry system, you can also lock or unlock all doors by operating the remote controller/transmitter.

  • Page 21: Keyless Start System Remote Controller/Keyless Entry System Transmitter

    The transmitter has only a keyless After using the emergency lever, be sure to entry system. For details, refer to the fol- see your SUZUKI dealer. lowing explanations. BEFORE DRIVING Type A...
  • Page 22 • If you lose one of the remote controllers, • The turn signal lights will flash twice. ask your SUZUKI dealer as soon as pos- • If the interior light switch is in the sible for a replacement. Be sure to have “DOOR”...
  • Page 23 Door Locks: 3, 5, 8 “PANIC” button (3) function This function is to get the attention of oth- ers. Press the “PANIC” button (3) for more than 1 second. The headlights and taillights will blink for about 30 seconds. Also, the horn will sound intermittently for about 30 sec- onds at the same time.
  • Page 24 • If you lose one of the remote controllers, television. ask your SUZUKI dealer as soon as pos- sible for a replacement. Be sure to have your dealer program the new remote controller code in your vehicle’s memory...
  • Page 25 Door Locks: 3, 5, 8 • You can use up to four remote controllers and ignition keys for your vehicle. Ask your SUZUKI dealer for details. • The battery life of the remote controller is about two years, but it can vary depending on usage conditions.
  • Page 26 Door Locks: 3, 5, 8 BEFORE DRIVING Replacement of the battery If the remote controller becomes unreli- able, replace the battery. To replace the battery of the remote con- troller: 66J016 1) Insert a flat blade screwdriver covered with a soft cloth in the slot of the remote controller and pry it open.
  • Page 27 • To purchase new remote controllers, see your SUZUKI dealer. • Before you begin programming, have all of your remote controllers available. To program a new remote controller 7.
  • Page 28 If you still cannot operate the systems, see your SUZUKI dealer. To change the old remote controller codes in your vehicle’s memory If you have lost one of the remote control- lers, you should change the remote con- troller codes in your vehicle’s memory as...
  • Page 29 • If you lose one of the transmitters, ask your SUZUKI dealer as soon as possible for a replacement. Be sure to have your dealer program the new transmitter code in your vehicle’s memory so that the old...
  • Page 30 5) Turn the ignition switch to the “LOCK” • To purchase new transmitters, see your position and remove the key within 10 SUZUKI dealer. seconds. All doors will lock/unlock to • Before you begin programming, have all confirm that this procedure has been of your transmitters available.
  • Page 31 Windows: 3, 8 52D212 6) Press the “UNLOCK” button (2) on the transmitter one time within 20 seconds (after step 5). All the doors will lock/ unlock to confirm that the procedure has been completed and the transmitter has been programmed. 7) If you want to program an additional transmitter, repeat the procedure from step 1) through step 6).

  • Page 32: Theft Deterrent Light

    Windows: 3, 8 Mirrors: 3, 8 BEFORE DRIVING Theft Deterrent Light EXAMPLE 78K013 This light will blink with the ignition switch in the “OFF” or “ACC” position. The blink- ing light is intended to deter theft by lead- ing others to believe that the vehicle is equipped with a security system.

  • Page 33: Mirrors

    Mirrors: 3, 8 CLOSE OPEN 81A009 To open a window, push the top part of the switch and to close the window lift up the top part of the switch. The driver’s window has an “auto-down” feature for added convenience (at toll booths or drive-through restaurants, for example).
  • Page 34 Seat Adjustment: 14 BEFORE DRIVING Mirrors Inside Rearview Mirror Day driving Night driving 78K033 You can adjust the inside rearview mirror by hand so as to see the rear of your vehi- cle in the mirror. To adjust the mirror, set the selector tab (1) to the day position, then move the mirror up, down or sideways by hand to obtain the best view.

  • Page 35: Front Seats

    Seat Adjustment: 14 Head Restraints: 3 Power Mirror Control (if equipped) 64J015 The switch to control the power rearview mirrors is located on the driver’s door panel. You can adjust the mirrors when the ignition switch is in the “ACC” or “ON” posi- tion.

  • Page 36: Seat Belts And Child Restraint Systems: 14

    Head Restraints: 3 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Adjusting Seat Position 64J016 The adjustment lever for each front seat is located under the front of the seat. To adjust the seat position, pull up on the adjustment lever and slide the seat forward or rearward.
  • Page 37 Seat Belts and Child Restraint Systems: 14 Head Restraints 63J256 Head restraints are designed to help reduce the risk of neck injuries in case of an accident. Adjust the head restraint to the position which places the center of the head restraint closest to the top of your ears.
  • Page 38 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING 79K036 To reinstall the head restraint, insert the head restraint bars into the holes (4) and push the head restraint down. 2-21 Front Seat Heater (if equipped) EXAMPLE 78K138 With the ignition switch in the “ON” posi- tion, push in one or both of the seat heater Improperly using the seat heater can switches to warm the corresponding...

  • Page 39: Rear Seats

    Seat Belts and Child Restraint Systems: 14 CAUTION To avoid damaging the heater ele- ment: • Do not subject the front seats to heavy impacts, such as children jumping on them. • Do not cover the seat with any insulating materials such as blan- kets or cushions.
  • Page 40 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Head Restraints Head restraints are designed to help reduce the risk of neck injuries in case of an accident. Adjust the head restraint to the position which places the center of the head restraint closest to the top of your ears.
  • Page 41 Seat Belts and Child Restraint Systems: 14 Folding Rear Seats The rear seat(s) of your vehicle can be folded forward to provide additional cargo space. To fold the rear seats forward: 1) Remove the luggage compartment cover. 66J211 2) Stow the seat belt buckles of the center and left seating position into the pocket of the seat cushion as shown in the illustration.
  • Page 42 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING 64J089 6) Fold the entire seat forward. 66J195 7) Push down the adjuster (2) to make the strap slack, and then unhook the strap by pushing down the hook (3). 2-25 Luggage or other cargo should be stowed in the luggage compartment with the rear seat in an upright posi-...

  • Page 43: Seat Belts And Child Restraint Systems

    Seat Belts and Child Restraint Systems: 14 64J091 2) Pull down the seat cushion until it locks into place. WARNING When returning the rear seat cushion to the normal position, be careful that your finger is not caught between the lock and the floor.
  • Page 44 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Above the pelvis 65D606 WARNING • Never allow persons to ride in the cargo area of a vehicle. In the event of an accident, there is a much greater risk of injury for persons who are not riding in a seat with their seat belt securely fastened.
  • Page 45 Seat Belts and Child Restraint Systems: 14 WARNING (Continued) • Do not wear your seat belt over hard or breakable objects in your pockets or on your clothing. If an accident occurs, objects such as glasses, pens, etc. under the seat belt can cause injury.
  • Page 46 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Safety reminder Sit up straight and fully back Low on hips 60A038 Low on hips 60A040 To reduce the risk of sliding under the belt during a collision, position the lap portion of the belt across your lap as low on your hips as possible and adjust it to a snug fit 2-29...
  • Page 47 Seat Belts and Child Restraint Systems: 14 78K126 NOTE: The word “CENTER” is molded into the buckle for the rear seat center belt. The buckles are designed so a latch plate can- not be inserted into the wrong buckle. Seat Belt Reminder Driver’s seat belt reminder light 60A039 To unfasten the belt, push the red...
  • Page 48 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING reminder light in the instrument cluster and the front passenger’s seat belt reminder light in the center of the instrument panel will come on and a buzzer will sound as a reminder to the driver and front passenger to buckle their seat belts.
  • Page 49 Seat Belts and Child Restraint Systems: 14 Driver’s seat belt reminder If the driver’s seat belt remains unbuckled with the ignition key in the “ON” position, the driver’s seat belt reminder works as fol- lows: 1) The driver’s seat belt reminder light will come on for about 20 seconds when the ignition key is turned to the “ON”...
  • Page 50 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Seat Belt Inspection EXAMPLE 65D209 Periodically inspect the seat belts to make sure they work properly and are not dam- aged. Check the webbing, buckles, latch plates, retractors, anchorages and guide loops.
  • Page 51 Infant restraint - rear seat only 65D584 Booster seat EXAMPLE 65D203 SUZUKI highly recommends that you use a child restraint system to restrain infants and small children. Many different types of Children could be endangered in a child restraint systems are available; make...
  • Page 52 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING 65D607 WARNING Do not install a rear-facing child restraint in the front passenger’s seat. If the passenger’s air bag inflates, a child in a rear-facing child restraint could be seriously injured. The back of a rear-facing child restraint would be too close to the inflating air bag.

  • Page 53: Supplemental Restraint System (Air Bags)

    Seat Belts and Child Restraint Systems: 14 Supplemental Restraint System (air bags): 3, 9, 12 ELR type belt EXAMPLE 65D233 Install your child restraint system accord- ing to the instructions provided by the child restraint system manufacturer. Make sure that the seat belt is securely latched.
  • Page 54 Supplemental Restraint System (air bags): 3, 9, 12 BEFORE DRIVING A-ELR type EXAMPLE 83E032 2) Allow the extra webbing to retract, and pull the webbing toward the retractor to take up any slack. Make sure that the lap portion of the belt is tight around the child restraint system and the shoulder portion of the belt is positioned so that it cannot interfere with the child’s head or...
  • Page 55 Supplemental Restraint System (air bags): 3, 9, 12 To revert from ALR to ELR EXAMPLE 65D267 When you unbuckle the seat belt and allow it to retract to a certain length, the retractor will automatically revert back to the normal ELR mode.
  • Page 56 Supplemental Restraint System (air bags): 3, 9, 12 BEFORE DRIVING EXAMPLE 65D340 3) Snap the strap hooks to the anchors. Take care not to pinch your fingers. EXAMPLE 65D341 4) Return the seatback to the normal, upright position. Tighten the lower straps as described in the child restraint 2-39 owner’s manual.
  • Page 57 Supplemental Restraint System (air bags): 3, 9, 12 EXAMPLE 54G184 4) Push the child restraint toward the anchors so that the connecting bar tips are partially hooked to the anchors. Use your hands to confirm the position. Installation-Child Restraint with Top EXAMPLE Strap Rear seat...
  • Page 58 If a seat belt cannot be fastened securely because it is not long enough, see your authorized SUZUKI dealer for a seat belt extender. Seat belt extenders are available for each seating position except for the rear center position.
  • Page 59 Upon activation, some noise will occur and some smoke may be released. This section of the owner’s manual These conditions are not harmful and do describes your SUZUKI’s SEAT BELT not indicate a fire in the vehicle. PRETENSIONER SYSTEM.

  • Page 60: Supplemental Restraint System (Air Bags)

    “LOCK” position for at least 90 seconds before performing any electri- cal service work on your SUZUKI. Do not touch pretensioner system components or wiring. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow.
  • Page 61 Supplemental Restraint System (air bags): 3, 9, 12 Your vehicle is equipped with a Supple- mental Restraint System consisting of the following components in addition to a lap- shoulder belt at each front seating position. 1. Driver’s front air bag 2.
  • Page 62 “AIR BAG” light stays on, or comes on while driving, the air bag system (or the seat belt pretensioner system) may not work properly. Have the air bag system inspected by an authorized SUZUKI dealer as soon as possible. 2-45 Front Air Bags dashboard.
  • Page 63 Front air bags will not inflate Front air bags are not designed to inflate in rear impacts, side impacts, rollovers or minor frontal collisions, since they would offer no protection in those types of acci- dents. Remember, since air bags deploy only one time during an accident, seat belts are needed to restrain occupants from further movements during the acci-...
  • Page 64 BEFORE DRIVING side air bag cover to identify the location of Side collision range the side air bags. Side air bags are designed to inflate only in 64J034 severe side impact collisions. Side curtain air bags are located in the roof Side curtain air bags are designed to lining.
  • Page 65 Side air bags and side curtain air bags will probably not inflate An air bag supplements, or adds to, the crash protection offered by seat belts. The driver and all passengers must be properly restrained by wear- ing seat belts at all times, whether or not air bags are mounted at their seating position, to minimize the risk of severe injury or death in the event...
  • Page 66 BEFORE DRIVING “PASS AIR BAG OFF” Indicator bag, depending on the front passenger’s seating posture and body build. The air bag should be turned off in the following situations: • There is no occupant in the front pas- senger seat. •...
  • Page 67 According to accident statistics, children are safer when properly restrained in rear seating positions than in front seating posi- tions. Whenever possible, SUZUKI recom- mends you install child restraints in the rear seat. The front passenger sensing system is designed to enable the front passenger’s...
  • Page 68 Have the system inspected by an authorized SUZUKI dealer as soon as possible. 2-51 How the System Works WARNING In a frontal collision, the crash sensors will detect rapid deceleration and send a signal to the controller.
  • Page 69 The air bag will neither hinder your view nor make it harder to exit the vehicle. Air bags must inflate quickly and forcefully in order to reduce the chance of serious or fatal injuries. However, an unavoidable consequence of the quick inflation is that the air bag may irritate bare skin, such as the facial area against a front air bag.
  • Page 70 SUZUKI dealer as soon as possible. objects could be propelled by the Special procedures are required for servic- air bag in the event of a crash.

  • Page 71: Instrument Cluster

    Instrument Cluster EXAMPLE 1. Speedometer 2. Tachometer 3. Fuel gauge 4. Temperature gauge 5. Information display 6. MODE/ILL knob 7. TRIP knob 8. Warning and indicator lights BEFORE DRIVING 79K118 2-54 79K21-03E...

  • Page 72: Warning And Indicator Lights

    BEFORE DRIVING Warning and Indicator Lights For details about the seat belt reminder, refer to “Seat Belts and Child Restraint Front Passenger’s Seat Belt Systems” in this section. Reminder Light It is absolutely essential that the driver and passengers wear their seat belts at all times.
  • Page 73 Have your vehicle inspected by an autho- rized SUZUKI dealer. Even if the light turns off after blinking, indicating that the monitoring system has recovered, make sure to have an authorized SUZUKI dealer check the system.
  • Page 74 If any of the following conditions fied level. The light should go out after fully occur, you should immediately ask releasing the parking brake, if the fluid your SUZUKI dealer to inspect the level in the brake fluid reservoir is ade- brake system. quate.
  • Page 75 If If one of these happens, have the system the light stays on, or comes on when driv- inspected by your SUZUKI dealer. If the ing and remains on, there may be some- ABS becomes inoperative, the brake sys-...
  • Page 76 ABS), the “ESP OFF” light comes on and ® the ESP systems (other than ABS). You stays on. should have the system inspected by an authorized SUZUKI dealer. NOTE: ® For details of the ESP systems, refer to • If the vehicle speed is greater than ®...
  • Page 77 SUZUKI dealer before you drive the vehicle again. For details of the hill descent control sys- tem, refer to “Hill descent control System”...
  • Page 78 WARNING or blinks when the engine is running, ser- vice to the emission control system is nec- essary. Bring the vehicle to your SUZUKI dealer to have the emission control system serviced right away and avoid hard accel- eration until the service is performed.
  • Page 79 NOTE: Open Door Warning Light If the fuel filler cap is not installed fully, the electrical system gets wet (such as by driv- ing through a deep puddle of water) or the fuel tank gets nearly empty, the malfunc- tion indicator lamp may come on. If so, the lamp will go off after driving a few times after the fuel filler cap is installed fully, the electrical system dries out or the fuel tank...
  • Page 80 BEFORE DRIVING Keyless Start System Indicator Turn Signal Indicators Light (if equipped) 62J041 When you turn on the left or right turn sig- nals, the corresponding green arrow on the When you push the ignition switch for vehi- instrument panel will flash along with the cle with the keyless start system, this light respective turn signal lights.
  • Page 81 Switch” in the “OPERATING YOUR VEHI- CLE” section. If the indicators (all lights) continue to blink, there is a problem in the transfer system inspected by an authorized SUZUKI dealer. NOTE: The information display shows the warning and indicator message when the transfer system is operated, or has a problem.

  • Page 82: Speedometer

    BEFORE DRIVING Speedometer Tachometer EXAMPLE EXAMPLE 79K119 The speedometer indicates vehicle speed The tachometer indicates engine speed in in km/h and mph. revolutions per minute. Never drive with the engine speed indicator in the red zone or severe engine damage can result. When downshifting to a lower gear, make sure not to operate with exces- sive revolution speeds of the engine.

  • Page 83: Temperature Gauge

    NOTE: Temperature Gauge The information display shows the warning and indicator message when this light comes on. CAUTION Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the catalytic converter. NOTE: The activation point of the low fuel warning light (1) varies depending on road condi-...

  • Page 84: Information Display (If Equipped)

    BEFORE DRIVING Information Display EXAMPLE (if equipped) The information display is shown when the ignition switch is in the “ON” position. 79K062 NOTE: • If you do not turn the brightness control knob within about 5 seconds of activat- ing the brightness control display, the brightness control display will be can- celed automatically.
  • Page 85 A/T Selector Position (for automatic transmission) EXAMPLE EXAMPLE 79K121 The display (A) shows the automatic trans- mission selector position. Fuel Consumption/Driving Range/ Average Speed When there are no warning or indicator messages on the display (B), you can select one of the following five indications to appear on the display, instantaneous fuel consumption, average fuel consump- tion, driving range, average speed, or no...
  • Page 86 BEFORE DRIVING Instantaneous fuel consumption You can select when the value of average If you selected instantaneous fuel con- fuel consumption is reset from among the sumption the last time you drove the vehi- following three methods; cle, the display does not show the bar •...
  • Page 87 Average speed Odometer/Trip meter/Thermometer If you selected average speed the last time When the ignition switch is turned to the you drove the vehicle, the display indicates “ON” position, the display (C) shows one of the last value of average speed from previ- the following three indications, trip meter A, ous driving when the ignition switch is trip meter B and thermometer.
  • Page 88 BEFORE DRIVING Thermometer Setting Mode The thermometer indicates the outside temperature. EXAMPLE When the ignition switch is in the “ON” 79K067 position and the vehicle is stationary, you If the outside temperature nears freezing, can enter the setting mode of the informa- the message shown in the above illustra- tion display by pushing and holding the tion will appear on the display.
  • Page 89 Distance units Warning and Indicator Messages You can change the units odo/trip meter The display shows the warning and indica- distance is displayed in. tor messages to let you know about certain vehicle problems. NOTE: A tone may also sound to alert you. When you change the units odo/trip meter If warning and indicator messages appear distance is displayed in, the trip meter will...
  • Page 90 (#1) Close all doors completely. Ding There may be a problem with the ESP Have your vehicle inspected by an authorized SUZUKI dealer. Ding There may be problem with the hill descent control sys- tem and the hill hold control system.
  • Page 91 )” in the “OPERATING YOUR VEHICLE” section for details. Sound Cause and Remedy There may be a problem with the 4WD system. Have your vehicle inspected by an authorized SUZUKI dealer. Ding Fuel is low. (#1) Fill the fuel tank immediately.

  • Page 92: Lighting Control Lever

    BEFORE DRIVING Lighting Control Lever 65D611 WARNING To avoid possible injury, do not oper- ate controls by reaching through the steering wheel. 2-75 Your vehicle’s lighting system is controlled by three main systems: the Lighting switch, the Auto-On Headlight System (when the lighting switch is in the “AUTO”...
  • Page 93 The three systems work together to operate your lights as shown in the following chart: E/G: Engine IG: Ignition switch ON: Lights ON LIGHT: When it is light around the light sensor (5). DARK: When it is dark around the light sensor (5). IG OFF Lighting Main lights to...
  • Page 94 BEFORE DRIVING Auto-On Headlight System HIGH PASS 79K016 With the headlights on, push the lever for- ward to switch to the high beams or pull The Auto-on headlight system automati- the lever toward you to switch to the low cally turns on all lights that are operated by beams.

  • Page 95: Front Fog Light Switch (If Equipped)

    Daytime Running Light (D.R.L.) Front Fog Light Switch System (if equipped) The headlights light, but are dimmer than the low beam, when the following three conditions are all met. Also, the D.R.L. indi- cator light on the instrument panel comes Conditions for D.R.L.

  • Page 96: Hazard Warning Switch

    BEFORE DRIVING Turn Signal Operation Hazard Warning Switch With the ignition switch in the “ON” posi- tion, move the lever up or down to activate the right or left turn signals. Push in the hazard warning switch to acti- vate the hazard warning lights. All turn sig- nal lights and both turn signal indicators will flash simultaneously.
  • Page 97 Windshield Wipers EXAMPLE EXAMPLE MIST 63J301 If the lever is equipped with the “INT TIME” To turn the windshield wipers on, move the control, turn the control forward or rear- lever up and down to one of the four oper- ward to adjust the intermittent wiper opera- tion to the desired interval.
  • Page 98 BEFORE DRIVING Rear Window Wiper/Washer Switch CAUTION EXAMPLE To help prevent damage to wind- shield wiper and washer system components, you should take the fol- lowing precautions: • Do not continue to hold in the lever when there windshield washer fluid being sprayed or the washer motor can be damaged.

  • Page 99: Tilt Steering Lock Lever

    Tilt Steering Lock Lever Horn EXAMPLE UNLOCK LOCK EXAMPLE 64J037 The lock lever is located under the steering Press the horn pad on the steering wheel column. To adjust the steering wheel to sound the horn. The horn will sound with height: the ignition switch in any position.
  • Page 100 BEFORE DRIVING An indicator light will be lit when the defroster is on. The defroster will only work when the engine is running. To turn off the defroster, push the switch (1) again. CAUTION The rear window defroster and the outside rearview mirrors use a large amount of electricity.

  • Page 101: Operating Your Vehicle

    OPERATING YOUR VEHICLE OPERATING YOUR VEHICLE Exhaust Gas Warning ... 3-1 Daily Inspection Checklist ... 3-2 Ignition Switch ... 3-3 Parking Brake Lever ... 3-7 Pedals ... 3-8 Starting the Engine ... 3-9 Engine Block Heater (if equipped) ... 3-10 Using the Transmission ...

  • Page 102: Exhaust Gas Warning

    Exhaust Gas Warning: NO OPERATING YOUR VEHICLE Exhaust Gas Warning 52D334 WARNING Avoid breathing exhaust gases. Exhaust gases contain carbon mon- oxide, a potentially lethal gas that is colorless and odorless. Since carbon monoxide is difficult to detect by itself, be sure to take the following precautions to help prevent carbon monoxide from entering your vehicle.

  • Page 103: Daily Inspection Checklist

    Daily Inspection Checklist: NO Starting the Engine: 1 Daily Inspection Checklist Before Driving 60A187S 1) Make sure that windows, mirrors, lights and reflectors are clean and unob- structed. 2) Visually check the tires for the following points: – the depth of the tread groove –...

  • Page 104: Ignition Switch

    Starting the Engine: 1 OPERATING YOUR VEHICLE Ignition Switch 65D611 WARNING To avoid possible injury, do not oper- ate controls by reaching through the steering wheel. Vehicle Without Keyless Start Sys- Manual transmission EXAMPLE • Manual transmission vehicles 60B041 You must push in the key to turn it to the The ignition switch has the following four “LOCK”...
  • Page 105 Starting the Engine: 1 Engine Block Heater: 1 Accessories such as the radio can oper- ate, but the engine is off. This is the normal operating position. All electrical systems are on. START This is the position for starting the engine using the starter motor.
  • Page 106 Engine Block Heater: 1 Using the Transmission: 10 OPERATING YOUR VEHICLE of the remote controller may be unreli- able. NOTE: • If the battery of the remote controller runs down or there are strong radio waves or noise, the operating range may be narrower or the remote controller may be inoperative.
  • Page 107 Using the Transmission: 10 ON (3) This is the normal operating position. All electrical systems are on. START (4) This is the position for starting the engine using the starter motor. The switch should be released from this position as soon as the engine starts.

  • Page 108: Parking Brake Lever

    64J081 inspected immediately by an autho- (1) To set rized SUZUKI dealer. (2) To release (3) To release The parking brake lever is located between the seats. To set the parking brake, hold...

  • Page 109: Pedals

    Brake Pedal (2) Your SUZUKI vehicle is equipped with front and rear disc brakes. Depressing the brake pedal applies both sets of brakes. You may hear occasional brake squeal when you apply the brakes.

  • Page 110: Starting The Engine

    WARNING If you are unable to start the engine using Make sure that the parking brake is this procedure, consult your SUZUKI set fully and the transmission is in dealer. Neutral (or Park for vehicles with an...

  • Page 111: Engine Block Heater (If Equipped)

    Using the Transfer Switch: 10 Engine Block Heater (if equipped) EXAMPLE 79K040 The engine block heater will help you start the engine more easily in very cold weather (–18°C (0°F) or below). To use the engine block heater: 1) Turn off the engine. 2) Open the engine hood.

  • Page 112: Using The Transmission

    Using the Transfer Switch: 10 OPERATING YOUR VEHICLE Using the Transmission Manual Transmission 65D449 Starting off To start off, depress the clutch pedal all the way to the floor and shift into 1st gear. After releasing the parking brake, gradually release the clutch.
  • Page 113 Using the Transfer Switch: 10 Gearshift lever 66J004 The gearshift lever is designed that it can- not be shifted out of the “P” position unless the ignition switch is in the “ON” position and the brake pedal is depressed. WARNING Always depress the brake pedal before shifting from “P”...
  • Page 114 Using the Transfer Switch: 10 OPERATING YOUR VEHICLE CAUTION Be sure to take the following precau- tions to help avoid damage to the automatic transmission: • Make sure that the vehicle is com- pletely stopped before shifting into “P” or “R”. •...
  • Page 115 Using the Transfer Switch: 10 Use the gearshift lever positions as described below: P (Park) Use this position to lock the transmission when the vehicle is parked or when start- ing the engine. Shift into Park only when the vehicle is completely stationary. WARNING If you have a 4-wheel drive vehicle, never leave the transfer switch in “N”...

  • Page 116: Using The Transfer Switch (If Equipped)

    Using the Transfer Switch: 10 OPERATING YOUR VEHICLE If You Cannot Shift Automatic Transmission Gearshift Lever Out of “P” (PARK) 78K043 Vehicles with an automatic transmission have an electrically operated park-lock fea- ture. If the vehicle’s battery is discharged, or there is some other electrical failure, the automatic transmission cannot be shifted out of Park in the normal way.
  • Page 117 Using the Transfer Switch: 10 Braking: 6 (11) (1) Front differential (2) Engine (3) Transmission (4) High/Low clutch (5) Transfer case (6) Center differential (7) Differential lock clutch (8) Chain (9) Rear propeller shaft (10) Rear differential (11) Front propeller shaft (10) 64J143 OPERATING YOUR VEHICLE...
  • Page 118 Braking: 6 OPERATING YOUR VEHICLE Description of Transfer Switch Positions N (Neutral) 3-17 In this position, engine power is not sup- plied to the front or rear axles. Only use this position for towing your vehicle. When you turn the transfer switch to the “N”...
  • Page 119 Braking: 6 OPERATING YOUR VEHICLE 4H (4-wheel drive high range) In this position, engine power is supplied to the front and rear axles. Use this position for normal driving. 64J220 3-18 79K21-03E...
  • Page 120 Tire Pressure Monitoring System (TPMS): OPERATING YOUR VEHICLE 4H LOCK (4-wheel drive high range center differential lock) 3-19 In this position, engine power is supplied to the front and rear axles and you get better traction than when driving in “4H”. Use this position when you need better traction than “4H”...
  • Page 121 Tire Pressure Monitoring System (TPMS): 4L LOCK (4-wheel drive low range center differential lock) OPERATING YOUR VEHICLE In this position, engine power is supplied to the front and rear axles and you get better traction and more low-speed torque than when driving in “4H”.
  • Page 122 Tire Pressure Monitoring System (TPMS): Break-In: 6 OPERATING YOUR VEHICLE Transfer Switch Operation Operate the transfer switch according to appropriate procedure described below: From N to 4H Stop the vehicle completely, place the transmission in “N” (Neutral) and depress the brake pedal and the clutch pedal fully (if equipped), then push in and turn the switch to shift into “4H”.
  • Page 123 Catalytic Converter: NO CAUTION • Be sure to stop the vehicle com- pletely before operating the trans- fer switch to shift between “N” and “4H”, or between “4H LOCK” and “4L LOCK”. • Do not shift between “4H” and “4H LOCK”...
  • Page 124 Catalytic Converter: NO Improving Fuel Economy: NO OPERATING YOUR VEHICLE The basic operation for transfer switch Current Position Current Indicator 4H LOCK 4L LOCK N: Neutral 4H: 4-wheel drive high range mode 4H LOCK: 4-wheel drive high range center differential lock mode 4L LOCK: 4-wheel drive low range center differential lock mode 3-23 Target Position...
  • Page 125 Cause and Remedy Indicator Blinks There may be a problem with the 4WD system. Have your vehicle inspected by an authorized SUZUKI dealer. 79K074 Blinks Series of This message informs you that the Beeps transfer switch is in “N”, which is used only for towing your vehicle.
  • Page 126 OPERATING YOUR VEHICLE Transfer Switch Warning and Indicator messages Operation Switching between “4H LOCK” and “4L LOCK” Switching between “4H” and “N” 3-25 Master Warning Sound Cause and Remedy Indicator Series of (For automatic transmission) Beeps The desired transfer gear has not been engaged.

  • Page 127: To Set Cruising Speed

    Cruise Control (if equipped) To help avoid loss of vehicle control, do not use the cruise control system when driving in heavy traffic, on slip- pery or winding roads, or on steep downgrades. 79K032 The cruise control system allows you to maintain a steady speed without keeping your foot on the accelerator pedal.
  • Page 128 OPERATING YOUR VEHICLE “CRUISE” indicator light To Change Speed Temporarily When the cruising speed is maintained, you can temporarily accelerate or deceler- ate. To accelerate, depress the accelerator pedal. When you take your foot off the pedal, your vehicle will return to the set speed.

  • Page 129: Braking

    Cancellation of the Cruise Control NOTE: If you turn off the cruise control system, the The “SET” indicator light will go off and the cruise control will be canceled temporarily previously set speed in the memory is with following procedures: cleared.
  • Page 130 OPERATING YOUR VEHICLE WARNING If water gets into the brake drums, Even without reserve power in the brake performance may become poor brake system, you can still stop the unpredictable. After driving vehicle by pressing the brake pedal through water or washing the under- harder than normally required.
  • Page 131 If both warning lights come on, drive carefully, avoid- ing hard braking as much as possi- ble, and ask your SUZUKI dealer to (Continued) inspect the ABS system immediately. WARNING...

  • Page 132: Electronic Stability Program (Esp®)

    OPERATING YOUR VEHICLE How the ABS Works Electronic Stability Program A computer continuously monitors wheel (ESP speed. computer compares changes in wheel speed when braking. If the wheels slow suddenly, indicating a skidding situation, computer will change braking pressure several times The Electronic Stability Program (ESP each second to prevent the wheels from helps to control the vehicle during corner-...
  • Page 133 ESP tems (other than ABS). You should ® may not work properly if have the systems inspected by an authorized SUZUKI dealer. NOTE: When the SLIP indicator light comes on and stays on while driving, indicating a ®...
  • Page 134 ESP tems (other than ABS). You should have the systems inspected by an authorized SUZUKI dealer. NOTE: When the “ESP” warning light comes on, or stays on while driving, indicating a mal-...
  • Page 135 “ESP OFF” switch When the “ESP OFF” switch located at the (without hill descent control) center of the instrument panel is pushed and held to turn off the ESP (other than ABS), the “ESP OFF” indicator light in the instrument cluster comes on. When you push and hold the “ESP OFF”...
  • Page 136 OPERATING YOUR VEHICLE Hill descent control System Hill descent control switch (if equipped) The hill descent control system is designed to reduce the driver’s workload when going down steep, rough and/or slippery hills where the vehicle cannot decelerate enough by engine braking alone. The hill descent control system helps to control vehicle speed by automatically engaging the vehicle’s brakes, as needed, so you...
  • Page 137 Have your vehicle inspected by an authorized SUZUKI dealer. NOTE: You cannot activate the hill descent control system while this message is displayed. 3-36 79K21-03E...
  • Page 138 Have inspected by an authorized SUZUKI dealer. NOTE: The hill hold control system will not acti- vate while this message is displayed. 79K072...

  • Page 139: Tire Pressure Monitoring System (Tpms) (If Equipped)

    SUZUKI dealer to register the ID As an added safety feature, your code of the spare tire sensor. Refer to vehicle has been equipped with a tire “Replacing Tires and/or Wheels”...
  • Page 140 Have your vehicle inspected by an autho- rized SUZUKI dealer. Even if the light turns off after blinking, indicating that the monitoring system has recovered, make sure to have an authorized SUZUKI dealer check the system.
  • Page 141 on the tire information placard should when the tires are cold. Tires that cause the low tire pressure warning light to appear to be at the specified pressure turn off. when checked after driving, when the tires are warm, could have pressure If the light turns on again shortly after below the specification when the tires adjusting the pressure in your tires, you...
  • Page 142 Replacing Tires and/or Wheels • If the low tire pressure warning If you get a flat tire, Suzuki recommends light comes on frequently, there that you have an authorized SUZUKI may be something wrong with one...

  • Page 143: Driving Tips

    DRIVING TIPS DRIVING TIPS Important Vehicle Design Features To Know ... 4-1 Break-In ... 4-2 Catalytic Converter ... 4-2 Improving Fuel Economy ... 4-3 On-Pavement Driving ... 4-4 Off-Road Driving ... 4-6 60G409 79K21-03E...

  • Page 144: Important Vehicle Design Features To Know

    Multipurpose vehicles such as your new SUZUKI have higher ground clearance and a narrower track than conventional pas- In a rollover crash, an unbelted person is senger cars, to make them capable of per-...

  • Page 145: Break-In

    Important Vehicle Design Features To Know: NO On-Pavement Driving: NO Shorter Wheelbase Along with its higher ground clearance, your vehicle has a shorter wheelbase and shorter front and rear overhangs than many passenger cars. These features combine to allow you to drive your vehicle over hillcrests without hanging up on them or damaging the frame and chassis com- ponents.

  • Page 146: Improving Fuel Economy

    On-Pavement Driving: NO Off-Road Driving: NO DRIVING TIPS CAUTION To minimize the possibility of catalyst or other vehicle damage: • Maintain the engine in the proper operating condition. • In the event of an engine malfunc- tion, particularly involving engine misfire or other apparent loss of performance, have the vehi- cle serviced promptly.

  • Page 147: On-Pavement Driving

    Off-Road Driving: NO Keep the air cleaner clean EXAMPLE 60A183S If the air cleaner is clogged with dust, there will be greater intake resistance, resulting in decreased power output and increased fuel consumption. Keep weight to a minimum The heavier the load, the more fuel the vehicle consumes.
  • Page 148 Off-Road Driving: NO DRIVING TIPS Don’t Make Sharp Turns As mentioned before, small multipurpose vehicles have specific design characteris- tics that allow them to perform in a wide variety of applications. These characteris- tics also change the cornering behavior relative to conventional passenger cars. Remember, small multipurpose vehicles have more responsive steering and a higher center of gravity than conventional...

  • Page 149: Off-Road Driving

    Off-Road Driving Do Not Turn on or Drive Across the Side of Hills Your vehicle has specific design character- Turning on or driving across the side of a istics for off-road driving. When you leave hill can be extremely hazardous. Most of the pavement, you will encounter driving the vehicle’s weight will be transferred to surfaces of all kinds which may change...
  • Page 150 DRIVING TIPS Tire Chains WARNING Tire chains should only be used if they are needed to increase traction or are required • Do not allow anyone to stand near by law. Make sure that the chains you use the vehicle when you are rocking it, are small-link chains or cable-type chains and do not spin the wheels faster and are the correct size for your vehicle’s...
  • Page 151 • Do not use tires other than those effectiveness. specified by SUZUKI. Never use dif- • Do not use “4H LOCK” or “4L ferent sizes or types of tires on the LOCK” drive for normal driving.
  • Page 152 DRIVING TIPS MEMO 79K21-03E...

  • Page 153: Other Controls And Equipment

    OTHER CONTROLS AND EQUIPMENT OTHER CONTROLS AND EQUIPMENT Automatic Heating and Air Conditioning System (Climate Control) ... 5-1 Radio Antenna ... 5-8 Audio Systems (Type A) ... 5-8 Audio Systems (Type B) ... 5-36 Fuel Filler Cap ... 5-62 Engine Hood ... 5-63 Sun Visor ...

  • Page 154: Automatic Heating And Air Conditioning System (Climate Control)

    Parking Brake Lever: 6 Pedals: 6 OTHER CONTROLS AND EQUIPMENT Automatic Heating and Air Conditioning System (Climate Control) Air Outlet EXAMPLE 1. Windshield defroster outlet 2. Side defroster outlet 3. Side outlet 4. Center outlet 5. Floor outlet Center outlet 66J250 EXAMPLE Open...
  • Page 155 Pedals: 6 Gearshift Lever: 10 Side outlet 63J045 When “Open”, air comes out from the side outlets regardless of the air flow selector position. OTHER CONTROLS AND EQUIPMENT Description of Controls (1) Temperature selector (2) Blower speed selector (3) Air intake selector (4) Air flow selector (5) Defrost switch (6) “OFF”...
  • Page 156 Gearshift Lever: 10 Fuel Filler Cap: 5 OTHER CONTROLS AND EQUIPMENT Temperature selector (1) 78K047 Turn the temperature selector (1) to adjust the temperature. Air conditioning switch (8) Blower speed selector (2) A/C: OFF A/C: ON 79K021 The air conditioning switch (8) is used to The blower speed selector (2) is used to turn on and off the air conditioning system.
  • Page 157 Fuel Filler Cap: 5 Folding Seats: 14 Air intake selector (3) 79K022 Push the air intake selector (3) to change between the following modes. If the “AUTO” switch (7) is pushed, the air intake will vary automatically as the climate control system maintains the selected tem- perature.
  • Page 158 Folding Seats: 14 OTHER CONTROLS AND EQUIPMENT Ventilation (c) 64J069 Temperature-controlled air comes out of the center and side air outlets. Bi-level (d) 64J070 Temperature-controlled air comes out of the floor outlets and cooler air comes out of the center and side outlets. When the temperature selector (1) is in the fully COLD position or fully HOT position, how- ever, the air from the floor outlets and the...
  • Page 159 You should have the system inspected by an autho- rized SUZUKI dealer. NOTE: • To find the temperature at which you are most comfortable, start with the 22°C (72°F) setting.
  • Page 160 Clean or replace them as specified in 64J074 “INSPECTION AND MAINTENANCE” sec- NOTE: tion. Have this job done by your SUZUKI If you need maximum defrosting: dealer as the lower glove box must be low- • push the defrost switch (5) to turn on the ered for this job.

  • Page 161: Radio Antenna

    Interior Light Switch: 7 Spot Light: 7 Radio Antenna 63J055 The radio antenna on the roof is remov- able. To remove the antenna, turn it coun- terclockwise. To reinstall the antenna, turn it clockwise firmly by hand. CAUTION avoid damage radio antenna: •...
  • Page 162 Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. Please bring the unit to an authorized SUZUKI dealer or a Clarion service Department. Cautions on Handling Never touch the surface.
  • Page 163 Front Seat Heater: 8 52D348 Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. 52D349 Do not use any solvents such as commer- cially available cleaners, anti-static spray, or thinner to clean compact discs. OTHER CONTROLS AND EQUIPMENT NOTE: •...

  • Page 164: Basic Operations

    Assist Grips: 3 Coat Hooks: Sunroof: 5, 8 OTHER CONTROLS AND EQUIPMENT Basic Operations Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-11 Display (1) Power on/off knob Volume control knob (2) Tone/balance/fader control knob (3) Preset button 5 (4) Preset button 6...
  • Page 165 Sunroof: 5, 8 Turning power on/off Press the power on/off knob (1). The unit starts in the function mode it was in when the power was turned off last. Adjusting the volume Turn the volume control knob (1). Turning it clockwise increases the volume; turning it counterclockwise decreases the volume.

  • Page 166: Listening To The Radio

    Sunroof: 5, 8 OTHER CONTROLS AND EQUIPMENT Listening to the Radio Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-13 Display (1) Band switch button (FM/AM) (2) Seek up button (3) Seek down button (4) Manual tuning knob (5) Preset buttons (1 to 6)
  • Page 167 Engine Hood: 5 Selecting the reception band Press the band switch button (1). Each time the button is pressed, the recep- tion band is switched as follows: 66J098 Seek tuning Press the seek up button (2) or the seek down button (3). The unit stops searching for a station at a frequency where a broadcast station is available.
  • Page 168 Cup Holder and Storage Bin: 3, 14 OTHER CONTROLS AND EQUIPMENT Radio Reception Radio reception can be affected by envi- ronment, atmospheric conditions, or radio signal’s power and distance from the sta- tion. Nearby mountains and buildings may interfere or deflect radio reception, causing poor reception.
  • Page 169 Overhead Console Box: Accessory Socket: 8 Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built in CD Player) OTHER CONTROLS AND EQUIPMENT Display (1) CD insertion slot (2) CD eject button (3) Disc button (CD/AUX) (4) Track up button/Fast forward button (5) Track down button/Rewind button (6) Repeat button (RPT) (A) Mode indicator...
  • Page 170 Accessory Socket: 8 Cigarette Lighter and Ashtray: 3, 8 OTHER CONTROLS AND EQUIPMENT Loading a CD Insert a CD in the CD insertion slot (1). When a CD is loaded, play starts and the CD indicator (A) lights. Ejecting a CD Press the CD eject button (2).
  • Page 171 Frame Hooks: 5, 6 Tire Changing Tools: 3, 5 Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Changer) OTHER CONTROLS AND EQUIPMENT Display (1) Load button (LOAD) (2) Disc select buttons (1 to 6) (3) CD insertion slot (4) CD eject button (5) Disc button (CD/AUX) (6) Track up button/Fast forward button...
  • Page 172 Tire Changing Tools: 3, 5 Shopping Hook: Front Seat Back Pocket: 3 OTHER CONTROLS AND EQUIPMENT NOTE: About Single CDs (8 cm CDs) • Since the unit is not compatible with a single CD, do not load it into the unit. •...
  • Page 173 Underseat Tray: 3 Luggage Restraint Loops: 5 Ejecting all the CDs Press the CD eject button (4) for 2 seconds or longer. All the CDs will be ejected from the unit in a sequential manner. • Please prepare location where removed CDs can be stored.
  • Page 174 Luggage Compartment Cover: 5 OTHER CONTROLS AND EQUIPMENT Listening to an MP3/WMA Disc Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-21 Display (Type 1) Display (Type 2) (1) Sound control knob (2) Repeat button (RPT) (3) Track up button/Fast forward button (4) Track down button/Rewind button...
  • Page 175 Underfloor Bins: Roof Rails or Roof Rack Anchors: 5, 13 What is MP3/WMA? MP3 (MPEG1/2 Audio Layer-III) and WMA (Windows Media Audio) are the com- pression formats of digital audio. The former is developed by MPEG (Motion Pic- ture Experts Group), and the latter is developed by Microsoft Corporation.
  • Page 176 Roof Rails or Roof Rack Anchors: 5, 13 HomeLink: OTHER CONTROLS AND EQUIPMENT Compression formats • Bit rate MPEG1 Audio Layer III : 32 k - 320 kbps MPEG2 Audio Layer III : 8 k - 160 kbps • Sampling frequency MPEG1 Audio Layer III : 44.1 k/48 k/32 MPEG2 Audio Layer III : 22.05 k/24 k/16 WMA (Ver.7, Ver.8, Ver.9*)
  • Page 177 HomeLink: NOTE: This operation should be performed within 2 seconds. To cancel repeat play, press the repeat but- ton (2) several times to change the repeat play mode to OFF. • TRACK REPEAT The indication “TRACK RPT” appears in the display for 2 seconds and then the repeat indicator (D) lights.

  • Page 178: Listening To A Xm Satellite Radio (Option)

    (A) Band (B) Channel number (C) Category indicator If you want to purchase XM Satellite Radio Service, contact your SUZUKI dealer. It is necessary to buy a special tuner to receive XM broadcasting. Your vehicle is capable of receiving XM...
  • Page 179 XM MODE Selecting a category Press the seek up button (3) or seek down Selecting a band button (4) to select a category. Press the XM button (1). Each time the button is pressed, the band Displaying the category changes in the following order. Press the category button (2) to have the currently selected category appear on the display.

  • Page 180: Listening To Audio For Aux (Option)

    OTHER CONTROLS AND EQUIPMENT Listening to Audio for AUX (Option) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-27 Display 66J221 (1) Aux button (CD/AUX) (A) Mode indicator Aux function This system has an external input terminal so you can listen to audio from an external device connected to this unit.
  • Page 181 Listening to a CD from an External CD Changer (Option) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL OTHER CONTROLS AND EQUIPMENT Display (A) (B) (1) Disc button (CD/AUX) (2) Disc select buttons (1 to 6) (3) Track up button/Fast forward button (4) Track down button/Rewind button (5) Repeat button (RPT)
  • Page 182 OTHER CONTROLS AND EQUIPMENT Selecting a CD changer mode Selecting a track Press the disc button (1). • Press the track up button (3) to listen to Each time the button is pressed, the the next track. selected CD plays as follows: •...

  • Page 183: Remote Audio Controls (If Equipped)

    • TRACK REPEAT Remote Audio Controls The indication “TRACK RPT” appears in (if equipped) the display for 2 seconds and then the repeat indicator (E) lights. The track being currently played is played repeatedly. • DISC REPEAT The indication “DISC RPT” appears in the display for 2 seconds and then the repeat indicator (E) lights.

  • Page 184: Anti-Theft Feature

    OTHER CONTROLS AND EQUIPMENT To change the selection on a CD: Anti-Theft Feature • To advance to the next track on a CD, push the upper part of the switch (4) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL briefly.
  • Page 185 (1) Power on/off knob NOTE: (2) Track up button/Fast forward button Establish your PIN by combining numbers (3) Preset buttons (1 to 6) from 1 to 6 into any 4-digit number. If you forget your PIN, when you remove the bat- The anti-theft feature is intended to dis- tery for repair etc., you will no longer be courage theft or the audio system by pre-...
  • Page 186 OTHER CONTROLS AND EQUIPMENT Confirming Your Personal Identifi- cation Number (PIN) When the main power source is discon- nected such as when you exchange your battery, etc, you will have to confirm your PIN to be able to use the audio system. To confirm your PIN: 66J121 2) Press the power on/off knob (1) while...

  • Page 187: Troubleshooting

    OTHER CONTROLS AND EQUIPMENT Cause Remedy Contact your authorized SUZUKI dealer. Contact your authorized SUZUKI dealer. Cause Remedy Tune correctly to the station frequency. Select stations by manual tuning.
  • Page 188 If a problem should occur, the display shows the type of error. Refer to the table below and take proper measures to correct the problem. If the problem is corrected, the unit will operate normally. Error display If an error display not listed above appears, turn off the unit and contact your SUZUKI dealer. 5-35 Measures to be taken CD/CD changer “Mechanical error”.

  • Page 189: Audio Systems (Type B)

    Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. Please bring the unit to an authorized 79KA001 SUZUKI dealer or a Clarion service Department. OTHER CONTROLS AND EQUIPMENT Cautions on Handling 52D274...
  • Page 190 OTHER CONTROLS AND EQUIPMENT Never touch the surface. 52D347 Never stick labels on the surface of the To remove fingermarks and dust, use a compact disc or mark the surface with a soft cloth, and wipe in a straight line from pencil or pen.
  • Page 191 Basic Operations AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) OTHER CONTROLS AND EQUIPMENT Display (1) Power on/off knob Volume control knob (2) Tone/balance/fader control knob (3) Preset button 5 (4) Preset button 6 (5) Clock button H (6) Clock button M (A) Clock display 79KA002...
  • Page 192 OTHER CONTROLS AND EQUIPMENT Turning power on/off • When minutes are between 30 and 59, Press the power on/off knob (1). the clock will reset to the next hour. (example: 12:38 ➔ 1:00) The unit starts in the function mode it was in when the power was turned off last.

  • Page 193: Listening To The Radio

    Listening to the Radio AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) OTHER CONTROLS AND EQUIPMENT Display (1) Band switch button (FM/AM) (2) Seek up button (3) Seek down button (4) Manual tuning knob (5) Preset buttons (1 to 6) (6) Auto store button (AS)/ Scan button (SCAN) (A) Band...
  • Page 194 OTHER CONTROLS AND EQUIPMENT Selecting the reception band Preset memory Press the band switch button (1). 1) Select the desired station. Each time the button is pressed, the recep- 2) Select the preset button (5) to which tion band is switched as follows: you want to store the station and press and hold the button for 2 seconds or longer.
  • Page 195 Radio Reception Listening to a CD Radio reception can be affected by envi- ronment, atmospheric conditions, or radio signal’s power and distance from the sta- tion. Nearby mountains and buildings may interfere or deflect radio reception, causing poor reception. Poor reception or radio static can also be caused by electric cur- rent from overhead wires or high voltage power lines.
  • Page 196 OTHER CONTROLS AND EQUIPMENT AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) 5-43 Display (1) CD insertion slot (2) CD eject button (3) Disc button (CD/AUX) (4) Track up button/Fast forward button (5) Track down button/Rewind button (6) Repeat button (RPT) (A) Mode indicator (B) Track number (C) Play time...
  • Page 197 Loading a CD Listening to a CD Insert a CD in the CD insertion slot (1). When a CD is inserted, it is automatically When a CD is loaded, play starts and the played back. CD indicator (A) lights. When a CD is already inside the unit, press the disc button (3) to play back the Ejecting a CD CD.
  • Page 198 OTHER CONTROLS AND EQUIPMENT Listening to an MP3/WMA Disc AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) 5-45 Display (1) Sound control knob (2) Repeat button (RPT) (3) Track up button/Fast forward button (4) Track down button/Rewind button (5) Display button (DISP) (A) Folder number (B) Track number...
  • Page 199 What is MP3/WMA? Points to remember when making MP3/ MP3 (MPEG1/2 Audio Layer-III) and WMA WMA files (Windows Media Audio) are the com- Common pression formats of digital audio. The • High bit rate and high sampling fre- former is developed by MPEG (Motion Pic- quency are recommended for high qual- ture Experts Group), and the latter is ity sounds.
  • Page 200 OTHER CONTROLS AND EQUIPMENT Compression formats Maximum number of files/folders • Maximum number of files: 999(files + folders) • Bit rate • Maximum number of files in one folder: MPEG1 Audio Layer III : 32 k - 320 kbps MPEG2 Audio Layer III : 8 k - 160 kbps •...
  • Page 201 NOTE: Selecting a track This operation should be performed within • Press the track up button (3) to listen to 2 seconds. the next track. • Press the track down button (4) twice to To cancel repeat play, press the repeat but- listen to the previous track.
  • Page 202 OTHER CONTROLS AND EQUIPMENT Listening to Audio for AUX AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) 5-49 Display (1) Aux button (CD/AUX) (2) Aux input connector (A) Mode indicator 79KA006 79K21-03E 80JA007...
  • Page 203 Aux function NOTE: This system has an external input terminal • AUX1 is displayed when an external so you can listen to audio from an external component is connected to the front- device connected to this unit. panel AUX input connector. •...
  • Page 204 (A) Band (B) Channel number (C) Category indicator If you want to purchase XM Satellite Radio Service, contact your SUZUKI dealer. It is necessary to buy a special tuner to receive XM broadcasting. Your vehicle is capable of receiving XM...
  • Page 205 XM MODE Selecting a category Press the seek up button (3) or seek down Selecting a band button (4) to select a category. Press the XM button (1). Each time the button is pressed, the band Displaying the category changes in the following order. Press the category button (2) to have the currently selected category appear on the display.
  • Page 206 OTHER CONTROLS AND EQUIPMENT Listening to Audio for AUX (Option) AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) 5-53 Display 80JA011 (1) Aux button (CD/AUX) (A) Mode indicator Aux function This system has an external input terminal so you can listen to audio from an external device connected to this unit.
  • Page 207 Listening to a CD from an External CD Changer (Option) AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) OTHER CONTROLS AND EQUIPMENT Display (A) (B) (1) Disc button (CD/AUX) (2) Disc select buttons (1 to 6) (3) Track up button/Fast forward button (4) Track down button/Rewind button (5) Repeat button (RPT) (6) Category button (CAT)
  • Page 208 OTHER CONTROLS AND EQUIPMENT Selecting a CD changer mode Selecting a track Press the disc button (1). • Press the track up button (3) to listen to Each time the button is pressed, the the next track. selected CD plays as follows: •...
  • Page 209 • TRACK REPEAT Remote Audio Controls The indication “TRACK RPT” appears in (if equipped) the display for 2 seconds and then the repeat indicator (E) lights. The track being currently played is played repeatedly. • DISC REPEAT The indication “DISC RPT” appears in the display for 2 seconds and then the repeat indicator (E) lights.
  • Page 210 OTHER CONTROLS AND EQUIPMENT To change the selection on a CD: Anti-Theft Feature • To advance to the next track on a CD, push the upper part of the switch (4) AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Player) briefly.
  • Page 211 (1) Power on/off knob NOTE: (2) Track up button/Fast forward button Establish your PIN by combining numbers (3) Preset buttons (1 to 6) from 1 to 6 into any 4-digit number. If you forget your PIN, when you remove the bat- The anti-theft feature is intended to dis- tery for repair etc., you will no longer be courage theft or the audio system by pre-...
  • Page 212 OTHER CONTROLS AND EQUIPMENT Confirming Your Personal Identifi- cation Number (PIN) When the main power source is discon- nected such as when you exchange your battery, etc, you will have to confirm your PIN to be able to use the audio system. To confirm your PIN: 66J121 2) Press the power on/off knob (1) while...
  • Page 213 OTHER CONTROLS AND EQUIPMENT Cause Remedy Contact your authorized SUZUKI dealer. Contact your authorized SUZUKI dealer. Cause Remedy Tune correctly to the station frequency. Select stations by manual tuning.
  • Page 214 If a problem should occur, the display shows the type of error. Refer to the table below and take proper measures to correct the problem. If the problem is corrected, the unit will operate normally. Error display If an error display not listed above appears, turn off the unit and contact your SUZUKI dealer. 5-61 Measures to be taken CD/CD changer “Mechanical error”.

  • Page 215: Fuel Filler Cap

    Fuel Filler Cap of the driver’s seat and can be locked by simply closing the door. EXAMPLE Open 78K145 To remove the fuel filler cap: EXAMPLE 1) Open the fuel filler door. 2) Remove the cap by turning it counter- clockwise.

  • Page 216: Engine Hood

    Engine Hood WARNING If you need to replace the fuel cap, use a genuine SUZUKI cap. Use of an improper cap can result in a malfunc- tion of the fuel system or emission control system. It may also result in fuel leakage in the event of an acci- dent.

  • Page 217: Sun Visor

    Sun Visor 64J112 3) Continue to lift up the hood until it is high enough to support with the prop The sun visors can be pulled down to block rod. glare coming through the windshield, or they can be unhooked and turned to the To close the engine hood: side to block glare coming through the side 1) Lift the hood up slightly and remove the...

  • Page 218: Luggage Compartment Light

    OTHER CONTROLS AND EQUIPMENT ON (1) The light comes on and stays on regard- EXAMPLE less of whether the door is open or closed. DOOR (2) The light comes on when the door is opened. After closing all doors (including the tail- gate), the light will remain on for about 15 seconds and then fade out.

  • Page 219: Spot Light

    remains off regardless of whether the Spot Light door(s) is(are) opened or closed. EXAMPLE Push the switch (1) to turn on the light and push it again to turn off the light. OTHER CONTROLS AND EQUIPMENT Accessory Socket (if equipped) EXAMPLE 65J093 EXAMPLE...

  • Page 220: Cigarette Lighter And Ashtray (If Equipped)

    OTHER CONTROLS AND EQUIPMENT The accessory socket will work when the Cigarette Lighter and Ashtray ignition switch is in the “ACC” or “ON” posi- (if equipped) tion. Cigarette Lighter 12-volt accessory sockets are located both on the center console and on the left side of the luggage compartment.

  • Page 221: Sunroof (If Equipped)

    Ashtray Sunroof (if equipped) You can tilt or slide the sunroof by operat- EXAMPLE ing the “TILT” part of the sunroof switch or the “SLIDE” part of the sunroof switch when the ignition switch is in the “ON” posi- tion. There is a system to prevent being pinched by the sunroof.
  • Page 222 OTHER CONTROLS AND EQUIPMENT 79K098 To slide the sunroof rearward, push the The sun shade will open automatically and “SLIDE OPEN” part (2) of the sunroof cannot be closed when the sunroof is slid switch. To side the sunroof forward, push rearward.

  • Page 223: Assist Grips (If Equipped)

    Assist Grips (if equipped) WARNING (Continued) • Always remove the ignition key when leaving the vehicle even if for a short time. Also do not leave chil- dren alone in a parked vehicle. Unattended children could use the sunroof switches and get trapped by the sunroof.

  • Page 224: Glove Box

    OTHER CONTROLS AND EQUIPMENT Glove Box Overhead Console Box (if equipped) EXAMPLE 78K136 (1) LOCK (2) UNLOCK To use the overhead console box, push on the front edge (1) and open the lid. To To open the glove box, pull the latch lever. close the lid, push the front edge (1) until it To close it, push the lid until it latches latches.

  • Page 225: Cup Holder And Storage Bin (If Equipped)

    Cup Holder and Storage Bin (if equipped) Cup holders and a storage bin are pro- vided as shown. EXAMPLE To use the console bin, pull the lever up and open the lid. 79K140 To access a bin, push the release button. To use the rear cup holders, open the lid.

  • Page 226: Front Seat Back Pocket (If Equipped)

    OTHER CONTROLS AND EQUIPMENT Front Seat Back Pocket Shopping Hook (if equipped) (if equipped) EXAMPLE The shopping hooks are located on both 64J127 sides of the luggage compartment. This pocket is provided for holding light and soft things such as gloves, newspa- You can hang the shopping bag or other pers or magazines.

  • Page 227: Floor Mats (If Equipped)

    When you replace the floor mats in your vehicle with a different type such as all- weather floor mats, we highly recommend using genuine SUZUKI floor mats for proper fitting. OTHER CONTROLS AND EQUIPMENT Luggage Compartment Cover...
  • Page 228 OTHER CONTROLS AND EQUIPMENT To remove the luggage compartment cover: 66J203 1) Release the three hooks (a) from the rear seat backs. 2) Fold and roll the cover forward. 5-75 rear front 3) Lift up both ends of the cover to disen- gage the attachment points (b).
  • Page 229 clearance is established on the other To stow a luggage compartment cover end to swing the cover down and out. on the floor of the rear luggage room: 78K147 5) Tilt the luggage compartment cover, and then remove the compartment cover from the vehicle.

  • Page 230: Underfloor Bins (If Equipped)

    OTHER CONTROLS AND EQUIPMENT 66J209 2) Align the attachment points (d) on the 3) Unroll/unfold the cover as you secure cover with the attachment points (b) on the other latches (e). the vehicle and push down both ends. Make sure that the cover securely fits in the attachment points.

  • Page 231: Luggage Restraint Loops (If Equipped)

    Luggage Restraint Loops (if equipped) The luggage restraint loops and optional rubber net can be used to help keep lightweight cargo from moving around in the luggage com- partment during normal driving. They are neither capable of nor intended for preventing cargo from being thrown around in a crash.
  • Page 232 • Mount and secure the cargo onto the anchors to attach the optional roof rack roof rack properly according to the which is available at your SUZUKI dealer. If instructions provided. Be sure to stow you use a roof rack, observe the instruc-...

  • Page 233: Homelink® (If Equipped)

    ® HomeLink (if equipped) any garage door opener model manufac- tured before April 1, 1982). A garage door that cannot detect an object – signaling the door to stop and reverse – does not meet current U.S. federal safety standards. For more information, contact HomeLink www.homelink.com or by calling 1-800- 355-3515.
  • Page 234 OTHER CONTROLS AND EQUIPMENT NOTE: Some gate operators and garage door openers may require you to replace this Programming step 3) with procedures noted in the “Gate Operator / Canadian Programming” section. ® 4) After the HomeLink indicator light changes from a slow to a rapidly blink- ®...
  • Page 235 Gate Operator / Canadian Program- Using HomeLink ming To operate, simply press and release the programmed HomeLink Canadian radio-frequency laws require will now occur for the trained device (i.e. transmitter signals to “time-out” (or quit) garage door opener, gate operator, secu- after several seconds of transmission –...

  • Page 236: Frame Hooks

    OTHER CONTROLS AND EQUIPMENT Frame Hooks Frame hooks are provided at the front and rear of the vehicle. Front To access the front hook, unhook the lower part of the cover (1) and then remove the cover (1). Do not use the frame hooks to tow another vehicle or to have your vehi- cle towed on the road or highway.

  • Page 237: Vehicle Loading And Towing

    VEHICLE LOADING AND TOWING VEHICLE LOADING AND TOWING Vehicle Loading ... 6-1 Trailer Towing ... 6-2 Towing Your Vehicle (recreational towing) ... 6-7 54G215 79K21-03E...

  • Page 238: Vehicle Loading

    Vehicle Loading: 11 VEHICLE LOADING AND TOWING Vehicle Loading 54G307 Your vehicle was designed for specific weight capacities. The weight capacities of your vehicle are indicated by the Gross Vehicle Weight Rating (GVWR), the Gross Axle Weight Rating (GAWR, front and rear) and the Vehicle Capacity Weight.

  • Page 239: Trailer Towing

    Trailer Towing: 5, 11, 13 Trailer Towing You can use your SUZUKI to tow a trailer, but you should always observe the require- ments and recommendations in this sec- tion. If you intend to tow a trailer, it is essential to select a trailer and trailer tow- ing equipment which are compatible.
  • Page 240 Trailer Towing: 5, 11, 13 VEHICLE LOADING AND TOWING Tires WARNING When towing a trailer, it is very important for your vehicle and trailer to have properly inflated tires. Your vehicle’s tires should be inflated to the recommended pressures listed on your vehicle’s Tire Inflation Pres- sure label.
  • Page 241 Trailer Towing: 5, 11, 13 Tongue Weight 60A380 Tongue Weight is the downward force exerted on the hitch by the trailer coupler, with the trailer fully loaded and the coupler at its normal towing height. Cargo should be distributed so that tongue weight is approximately 10% of gross trailer weight.
  • Page 242 Trailer Towing: 5, 11, 13 VEHICLE LOADING AND TOWING WARNING Never overload your trailer or your vehicle. Gross Trailer Weight must never exceed 1350 kg (3000 pounds). Gross Combined Weight must never exceed 3400 kg (7500 pounds) for 2WD or 3450 kg (7600 pounds) for 4WD.
  • Page 243 Trailer Towing: 5, 11, 13 WARNING (Continued) • Avoid “riding” the brakes. “Riding” the brakes could cause the brakes to overheat, resulting in reduced braking efficiency. engine braking as much as possible. • Because added trailer weight, your engine may overheat on hot days when going up long or steep hills.

  • Page 244: Towing Your Vehicle (Recreational Towing)

    Towing Your Vehicle (recreational towing): 13 VEHICLE LOADING AND TOWING Towing Your Vehicle (recreational towing) Your vehicle may be towed behind another vehicle (such as a motorhome), provided you use the proper towing method speci- fied for your vehicle. The towing method you must use depends on the specifica- tions of your vehicle: whether it is a 2- wheel drive (2WD), 4-wheel drive (4WD)
  • Page 245 Towing Your Vehicle (recreational towing): 13 WARNING When you tow your vehicle, follow the instructions below to avoid acci- dents and damage to your vehicle. In addition, be sure to observe govern- ment and local requirements regard- ing vehicle lighting and trailer hitches or tow bars.
  • Page 246 Towing Your Vehicle (recreational towing): 13 VEHICLE LOADING AND TOWING 7) Release the parking brake. Stop towing the vehicle every 300 km (200 miles). Start the engine. With the manual transmission lever in 2nd gear (or the auto- matic transmission lever in “D”) and the transfer switch in neutral, rev the engine for about one minute with the clutch engaged (if equipped), to circulate oil in the transfer...
  • Page 247 Towing Your Vehicle (recreational towing): 13 4WD Vehicle Without a Transfer Switch 54G586 54G585 VEHICLE LOADING AND TOWING 2WD Vehicle 1) Secure the rear wheels on a towing dolly according to the instructions pro- vided by the dolly manufacturer. 2) Turn the ignition key to the “ACC” posi- tion to unlock the steering wheel.
  • Page 248 Towing Your Vehicle (recreational towing): 13 VEHICLE LOADING AND TOWING TOWING METHOD B FRONT WHEELS ON THE GROUND AND REAR WHEELS ON A DOLLY. 6-11 52D082 79K21-03E...

  • Page 249: Inspection And Maintenance

    INSPECTION AND MAINTENANCE INSPECTION AND MAINTENANCE Maintenance Schedule ... 7-2 Periodic Maintenance Schedule ... 7-3 Maintenance Recommended under Severe Driving Conditions ... 7-7 Drive Belt ... 7-9 Engine Oil and Filter ... 7-10 Engine Coolant ... 7-13 Air Cleaner ... 7-16 Spark Plugs ...

  • Page 250: Inspection And Maintenance

    • Do not get under your vehicle if it is electrical service work on your supported only with the portable SUZUKI. Do not touch air bag sys- jack provided in your vehicle. tem components or wires. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow for easy identification.

  • Page 251: Maintenance Schedule

    SUZUKI recommends that mainte- nance on items marked with an aster- performed your authorized SUZUKI dealer or a quali- fied service technician. If you are qualified, you may perform mainte- nance on the unmarked items by referring to the instructions in this section.

  • Page 252: Periodic Maintenance Schedule

    #2: Be sure to perform the engine coolant level check under the daily inspection in “OPERATING YOUR VEHICLE” section. If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow the schedule of SUZUKI LLC: Standard (Green).
  • Page 253 #2: Be sure to perform the engine coolant level check under the daily inspection in “OPERATING YOUR VEHICLE” section. If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow the schedule of SUZUKI LLC: Standard (Green).
  • Page 254 Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10 INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by miles (x 1000) odometer reading or months, whichever comes km (x 1000) first.
  • Page 255 Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10 R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by miles (x 1000) odometer reading or months, whichever comes km (x 1000) first.

  • Page 256: Maintenance Recommended Under Severe Driving Conditions

    Maintenance Recommended under Severe Driving Condi- tions: 1, 2, 3, 4, 5, 6, 9, 10 INSPECTION AND MAINTENANCE Maintenance Recommended under Severe Driving Conditions If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is recommended that appli- cable maintenance operation be performed at the particular interval shown in the chart below.
  • Page 257 Maintenance Recommended under Severe Driving Condi- tions: 1, 2, 3, 4, 5, 6, 9, 10 Severe Maintenance Condition Code – B – – E H Automatic transmission (A/T) fluid – B – – E H Transfer, Differential and Extension oil –...

  • Page 258: Drive Belt

    You do not need check it for ten- sion as it has an automatic tensioner. If you need to replace or adjust the belt have it done by your SUZUKI dealer. L4 2.4 L V6 3.2 L →: 100 N (22 lbs, 10 kg) press...

  • Page 259: Engine Oil And Filter

    Engine Oil and Filter: 1, 2 Engine Oil and Filter Specified Oil “Starburst” 79K096 Use engine oil with the American Petro- leum Institute Certified For Gasoline Engines “Starburst” symbol. We highly recommend you use SAE 5W- 30 oil. CAUTION Failure to use the recommended oil can result in engine damage.
  • Page 260 Engine Oil and Filter: 1, 2 INSPECTION AND MAINTENANCE Refilling EXAMPLE Open Close 81A147 Remove the oil filler cap and pour oil slowly through the filler hole to bring the oil level to the upper limit on the dipstick. Be careful not to overfill.
  • Page 261 NOTE: • When it is difficult to remove the oil filter, we recommend you take your vehicle to your SUZUKI dealer for oil filter replace- ment. • For 3.2 L engine, since special proce- dures are required, we recommend you take your vehicle to your SUZUKI dealer for oil filter replacement.

  • Page 262: Engine Coolant

    Genuine Coolant or equivalent. 64J151 NOTE: If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow EXAMPLE the schedule of SUZUKI LLC: Standard (Green). To see the detail of the mainte- nance schedule, refer to “Periodic Mainte- nance Schedule”...
  • Page 263 70/30 coolant to distilled water will cause over- heating conditions. • Do not use straight coolant nor plain water (except SUZUKI LLC: Super (Blue)). • Do not add extra inhibitors or addi- tives. They may not be compatible with your cooling system.
  • Page 264 Automatic Transmission Fluid: 10 Engine Coolant: 1, 2 INSPECTION AND MAINTENANCE Engine Coolant Replacement Open Close 66J151 1) When the engine is cool, remove the radiator cap by turning it slowly to the left until a “stop” is felt. Do not press down while turning the cap.

  • Page 265: Air Cleaner

    Engine Coolant: 1, 2 Air Cleaner EXAMPLE 66J167 If the air cleaner is clogged with dust, there will be greater intake resistance, resulting in decreased power output and increased fuel consumption. Check and clean periodically according to the following procedure: 1) Take off the air cleaner case cover.

  • Page 266: Gear Oil

    For the speci- fied plugs, refer “SPECIFICATIONS” section at the end of this book. If you wish to use a brand of spark plug other than the specified plugs, consult your SUZUKI dealer. 54G095 65D594 79K21-03E...
  • Page 267 Windshield Washer Fluid: 3 Air Cleaner: 1, 2 API GRADE Transmission/ GL-4 Extension case Transfer case GL-5 Front (Hypoid gear oil) Differential Rear INSPECTION AND MAINTENANCE Manual transmission Extension case (2WD) 52D087 Transfer case (1) Oil filler and level plug (2) Oil drain plug 66J005 (1) Oil filler and level plug...
  • Page 268 When tightening these plugs, apply sealing compound “SUZUKI Bond No. 1217G” or equivalent to the plug threads to prevent oil leakage and tighten them to the specified torque shown below.

  • Page 269: Clutch Pedal

    1) To warm up the transmission fluid, drive depressed, have the clutch inspected by the vehicle or idle the engine until the your SUZUKI dealer. If the clutch fluid level temperature gauge indicates normal is near the “MIN” line, fill it up to the “MAX”...

  • Page 270: Brakes: 6

    The handle of the A/T fluid dipstick is col- you trust this job to your authorized ored red for easy identification. SUZUKI dealer. FULL HOT LOW HOT 65D109 6) Remove the dipstick, clean it and push it back in until the cap seats.

  • Page 271: Steering Wheel: 6

    Should the light come on, immedi- cal attention. Wash thoroughly after ately ask your SUZUKI dealer to handling. Solution can be poisonous inspect the brake system. to animals. Keep out of the reach of •...

  • Page 272: Tires: 6

    If the pedal to floor carpet distance as 7-23 measured above is less than the minimum distance required, have your vehicle inspected by your SUZUKI dealer. NOTE: When measuring the distance between the brake pedal and floor wall, push in the floor...

  • Page 273: Steering Wheel

    If the parking brake is not properly adjusted or the brakes drag after the lever has been fully released, have the parking brake inspected and/or adjusted by your SUZUKI dealer. INSPECTION AND MAINTENANCE Steering Wheel Power Steering (if equipped) EXAMPLE “c”...

  • Page 274: Tire Sidewall Labeling

    Tires: 6 INSPECTION AND MAINTENANCE Tires For safe operation of your vehicle, it is important that the tires be the correct type and size, in good condition, and properly inflated. Be sure to follow the requirements and recommendations in this section. Tire Sidewall Labeling Useful information about a tire is molded into its sidewall.
  • Page 275 The following illustration shows an example of a typical passenger car tire size. EXAMPLE E. Rim Diameter Your SUZUKI is equipped with tires which are all the same type and size. This is important to ensure proper steering and han- 67D028 dling of the vehicle.

  • Page 276: Tire Inflation Pressure

    Tires: 6 INSPECTION AND MAINTENANCE Tire Inflation Pressure Tire inflation pressure should be checked when the tire is cold. “Cold tire inflation pressure” is the pressure in a tire that has been driven less than 1 mile (1.6 km) or has been standing for three hours or more.
  • Page 277 Tires: 6 tire gauge until you reach the cor- rect pressure. 5) If the air pressure is too low, fill the tire with air at a service station until it reaches the recommended pres- sure. 6) Make sure all tires have the same air pressure (unless the owner’s manual indicates otherwise).
  • Page 278 5) Check that there are no nails, stones or other objects sticking into the tires. 7-29 WARNING Your SUZUKI is equipped with Replacing the wheels and tires tires which are all the same type equipped on your vehicle with and size. This is important to...

  • Page 279: Uniform Tire Quality Grading

    U.S. Consult your SUZUKI dealer or tire retailer for help in choosing the correct replacement tires for your vehicle. Quality grades can be found where...
  • Page 280 Tires: 6 INSPECTION AND MAINTENANCE Tire Rotation 4-tire rotation 65D459 To avoid uneven wear of your tires and to prolong their life, rotate the tires as illustrated. Tires should be rotated as recommended in the periodic mainte- nance schedule. After rotation, adjust front and rear tire pressures to the specification listed on your vehicle’s Tire and Loading Information Label.

  • Page 281: Battery: 9

    For improved traction in severe winter conditions, SUZUKI recommends mounting radial snow tires on all four wheels. Snow tires must be the same size as the standard tires. Also be sure...
  • Page 282 Fuses: 7 INSPECTION AND MAINTENANCE Recommended Inflation Pressure – the cold tire inflation pressure recom- mended by a manufacturer. Rim – metal support for a tire or tire and tube assembly upon which the tire beads are seated. Vehicle Capacity Weight – the rated cargo and luggage load plus 68 kilo- grams (150 lbs) times the vehicle’s designated seating capacity.
  • Page 283 Fuses: 7 exceed the total load capacity of the vehicle. Total Load Capacity – Maximum per- missible weight a vehicle can carry including the weight of all the occu- pants, accessories, cargo, plus trailer tongue weight (if towing a trailer). The weight of any accessories already installed on your vehicle at the time of purchase, or that you or the dealer...
  • Page 284 Fuses: 7 Headlight Aiming: Bulb Replacement: 7 INSPECTION AND MAINTENANCE gers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 – 750 (5 x 150) = 650 lbs). 5) Determine the combined weight of luggage and cargo being loaded on the vehicle.
  • Page 285 Bulb Replacement: 7 Battery EXAMPLE 60A269 WARNING Batteries produce flammable hydro- gen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when work- ing near the battery. WARNING When checking or servicing the bat- tery, disconnect the negative cable.
  • Page 286 SUZUKI engine compartment. If the main fuse dealer. Always use a genuine SUZUKI blows, no electrical component will func- replacement. Never use a substitute tion. If a primary fuse blows, no electrical...

  • Page 287: Fuse Under The Dash Board

    Bulb Replacement: 7 Fuse under the Dash Board Fuse box 64J192 79K057 INSPECTION AND MAINTENANCE DOME Dome lamp fuse STOP Stop lamp fuse – – Blank Accessory socket ACC 3 fuse CRUISE Cruise control fuse Cigar or Accessory ACC 2 socket fuse Wiper fuse Ignition signal &...

  • Page 288: Headlight Aiming

    SUZUKI dealer. NOTE: Make sure that the fuse box cover always carries spare fuses. 7-39 Headlight Aiming Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for headlight alignment. BLOWN 60A243 BLOWN 81A283 79K21-03E...

  • Page 289: Bulb Replacement

    Frequent replacement of a bulb indi- cates the need for an inspection of the electrical system. This should be carried out by your SUZUKI dealer. NOTE: If it is difficult to replace headlight bulbs or clearance light bulbs due to under-hood components trust this job to your dealer.
  • Page 290 Wiper Blades: 3 INSPECTION AND MAINTENANCE Spot Light (if equipped) Pull down the lens by using a flat blade screwdriver covered with a soft cloth as shown. Ceiling-mount type (if equipped) 79K061 Remove the bulb holder by turning it coun- terclockwise.
  • Page 291 Wiper Blades: 3 Front Fog Light 79K090 1) Insert a flat blade screwdriver into the hole (2) and remove the clips (1) by twist the driver as shown in the illustra- tion. 2) Remove the bolt (3) by a Phillips-head screwdriver.
  • Page 292 Air Conditioning System: 4 INSPECTION AND MAINTENANCE Other General Lights Bulb holder EXAMPLE 54G123 (1) Removal (2) Installation To remove a bulb holder from a light hous- ing, turn the holder counterclockwise and pull it out. To install the holder, push the holder in and turn it clockwise.
  • Page 293 Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for the bulbs of high-mount stop light replacement. 64J165 64J181 To remove a high-mounted stop light hous-...
  • Page 294 INSPECTION AND MAINTENANCE 64J182 2) Release the claws of the light housing 3) Close the tailgate. Remove a high- by the flat head etc. through the service mounted stop light housing (2) from the holes as shown in the illustration. tailgate.

  • Page 295: Wiper Blades

    NOTE: Some wiper blades may be different from the ones described here depending on vehicle specifications. If so, consult your SUZUKI dealer for proper replacement method. INSPECTION AND MAINTENANCE 52D102 70G119 2) Squeeze lock lever (1) towards wiper arm (2) and remove the wiper frame from the arm as shown.
  • Page 296 INSPECTION AND MAINTENANCE 60A260 3) Pull the locked end of the wiper blade (3) Retainer firmly to unlock the blade and slide the blade out as shown. 4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one.
  • Page 297 For rear wipers: NOTE: Do not flex the wiper blade frame end more than necessary. If you do, it can break off. 80G146 1) Hold the wiper arm away from the win- dow. 2) Remove the wiper frame from the arm as shown.

  • Page 298: Air Conditioning System

    INSPECTION AND MAINTENANCE Windshield Washer Fluid fluid tank. If the fluid level is near empty, refill it. Front and rear (if equipped) Use a good quality windshield washer EXAMPLE fluid, diluted with water as necessary. Do not use “anti-freeze” solution in the windshield washer reservoir.

  • Page 299: Emergency Service

    EMERGENCY SERVICE EMERGENCY SERVICE Tire Changing Tool ... 8-1 Spare Tire Nut Lock (if equipped) ... 8-1 Jacking Instructions ... 8-2 Changing Wheels ... 8-3 Jump Starting Instructions ... 8-7 Towing a Disabled Vehicle ... 8-8 If the Starter Does Not Operate ... 8-8 If the Engine is Flooded ...

  • Page 300: Tire Changing Tool

    Jacking Instructions: 5 EMERGENCY SERVICE Tire Changing Tool 64J124 The jack, wheel brace and jack handle are stowed in the rear left corner of the lug- gage compartment. Remove the cover to access the tools. To remove the jack, turn its shaft counter- clockwise and pull the jack out of the stor- age bracket.

  • Page 301: Jacking Instructions: 5

    Jacking Instructions: 5 Jacking Instructions 75F062 1) Place the vehicle on level, hard ground. 2) Set the parking brake firmly and shift into “P” (Park) if your vehicle has an automatic transmission, or shift into “R” (Reverse) if your vehicle has a manual transmission.

  • Page 302: Changing Wheels

    Jump Starting Instructions: 7 EMERGENCY SERVICE WARNING • Use the jack only to change wheels on level, hard ground. • Never jack up the vehicle on an inclined surface. • Never raise the vehicle with the jack in a location other than the designated jacking point near the wheel to be changed.

  • Page 303: Towing A Disabled Vehicle: 6

    Jump Starting Instructions: 7 Towing a Disabled Vehicle: 6 If the Starter Does Not Operate: 2, 9 NOTE: Remove the full wheel cover from the bot- tom part to the upper part. Otherwise, the claws may be broken. (Half cover type) 78K060 NOTE: If your vehicle is equipped with the half...

  • Page 304: If The Engine Is Flooded

    If you do not have a torque wrench, have the wheel nut torque checked by an authorized SUZUKI dealer. To install the wheel: 78K154 1) Install the wheel with both hands to the spare tire carrier (1) as shown in the illustration.
  • Page 305 For improved using this spare: traction • Be aware that your vehicle will han- SUZUKI recommends mounting radial dle differently with this temporary snow tires on all four wheels. Snow tires spare. must be the same size as the standard •...

  • Page 306: Jump Starting Instructions

    • If your battery discharges repeat- edly, for no apparent reason, have your vehicle inspected by an autho- rized SUZUKI dealer. • To avoid harm to yourself or dam- 1) Use only a 12-volt battery to jump start age to your vehicle or battery, fol- your vehicle.

  • Page 307: Towing A Disabled Vehicle

    2) If the headlights remain bright, check the fuses. If the reason for failure of the starter is not obvious, there may be a major electrical problem. Have the vehi- inspected SUZUKI dealer. CAUTION your authorized 79K21-03E...

  • Page 308: If The Engine Is Flooded

    EMERGENCY SERVICE If the Engine is Flooded If the Engine Overheats If the engine is flooded with gasoline, it The engine could overheat temporarily may be hard to start. If this happens, press under severe driving conditions. If the the accelerator pedal all the way to the engine coolant temperature gauge indi- floor and hold it there while cranking the cates overheating during driving:...
  • Page 309 66J191 WARNING • It is hazardous to remove the radia- tor cap when the water temperature is high, because scalding fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant temper- ature has lowered.
  • Page 310 EMERGENCY SERVICE MEMO 8-11 79K21-03E...

  • Page 311: Appearance Care

    APPEARANCE CARE APPEARANCE CARE Corrosion Prevention ... 9-1 Vehicle Cleaning ... 9-3 60G412 79K21-03E...

  • Page 312: Corrosion Prevention

    Corrosion Prevention: 5 APPEARANCE CARE Corrosion Prevention It is important to take good care of your vehicle to protect it from corrosion. Listed below are instructions for how to maintain your vehicle to prevent corrosion. Please read and follow these instructions carefully.
  • Page 313 UV rays in sunlight, and can reduce the amount of dust and air pollution reaching the surface. Your SUZUKI dealer can help you select the right cover for your vehicle. APPEARANCE CARE...

  • Page 314: Vehicle Cleaning

    Vehicle Cleaning: 5 APPEARANCE CARE Vehicle Cleaning 76G044S WARNING When cleaning the interior or exterior of the vehicle, NEVER USE flammable solvents such lacquer thinners, gas- oline, benzene or cleaning materials such as bleaches and strong house- hold detergents. The materials could cause personal injury or damage to the vehicle.
  • Page 315 Vehicle Cleaning: 5 Cleaning the Exterior CAUTION It is important that your vehicle be kept clean and free from dirt. Failure to keep your vehicle clean may result in fading of the paint or corrosion to various parts of the vehicle body. Washing WARNING •...
  • Page 316 APPEARANCE CARE Waxing 60B211S After washing the vehicle, waxing and pol- ishing are recommended to further protect and beautify the paint. • Only use waxes and polishes of good quality. • When using waxes polishes, observe the precautions specified by the manufacturers.

  • Page 317: General Information

    GENERAL INFORMATION GENERAL INFORMATION Identification Numbers ... 10-1 Safety Certification Label ... 10-2 Emission Compliance Label (for U.S.A.) ... 10-2 Warranties ... 10-2 On-Board Vehicle Computers and Event Data Recorders ... 10-3 Reporting Safety Defects ... 10-4 54G072 79K21-03E...

  • Page 318: Identification Numbers

    Identification Numbers: 2, 5 GENERAL INFORMATION Identification Numbers Vehicle Identification Number EXAMPLE (for some vehicles) 60G152 64J197 10-1 The Vehicle Identification Number (VIN) 3.2 L engine model may be found in the two locations shown in the above illustrations. This number is used to register the vehicle.

  • Page 319: Safety Certification Label: 6

    For U.S.A. The following warranties are provided with your vehicle: • New Vehicle Limited Warranty • Limited Warranty For SUZUKI Parts or Accessories • Emission Components Defect Warranty • Emission Performance Warranty 60A412 The EPA emission compliance label is located under the hood.

  • Page 320: On-Board Vehicle Computers And Event Data Recorders

    SUZUKI’s defense of litiga- tion through the discovery process, or as required by law. research...

  • Page 321: Reporting Safety Defects

    For vehicles registered for use and NHTSA cannot become involved in principally operated in Canada please individual problems between you, your contact Suzuki Canada Inc. at 1-905- dealer, or American Suzuki Motor 889-2677 extension 2254 or write to: Corp. Suzuki Canada Inc.
  • Page 322 GENERAL INFORMATION MEMO 10-5 79K21-03E...

  • Page 323: Fuses And Protected Circuits

    Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS COLOR (AMPS) BLUE (15) CPRSR YELLOW (20) O2 HTR BLUE (15) THR MOT YELLOW (20) MAIN CLEAR (25) RR DEF FUSE BOX BLUE (15) HORN YELLOW (20) FR FOG YELLOW (20) MRR HTR GREEN (40) FR BLW...
  • Page 324 Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS COLOR (AMPS) (11) RED (50) ABS 1 (12) YELLOW (20) (13) – – (14) RED (10) H/L L MAIN (15) RED (10) H/L R FUSE BOX (16) RED (10) (17) GREEN (40) ST MTR (18) GREEN (40)
  • Page 325 FUSES IN FUSE BOX RED (10) DOME Dome lamp fuse RED (10) STOP Stop lamp fuse – – Blank BLUE (15) ACC 3 Accessory socket fuse RED (10) CRUISE Cruise control fuse Cigar or Accessory socket BLUE (15) ACC 2 fuse YELLOW (20) Wiper fuse...
  • Page 326 FUSES AND PROTECTED CIRCUITS MEMO 11-4 79K21-03E...

  • Page 327: Specifications

    Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS NOTE: Specifications are subject to change with- out notice. ITEM: Dimensions Overall length Overall width Overall height Wheelbase Tread Minimum running ground clearance ITEM: Weight Gross axle weight rating Gross vehicle weight rating Vehicle capacity weight 4WD: 4-wheel drive M/T: Manual transmission...
  • Page 328 Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS ITEM: Engine Type Number of cylinders Bore Stroke Piston displacement Compression ratio ITEM: Electrical Ignition timing Standard spark plug Battery Fuses 12-2 J24B (16V DOHC) N32A (24V DOHC) 92.0 mm (3.62 in.) 89.0 mm (3.50 in.) 90.0 mm (3.54 in.) 85.6 mm (3.37 in.)
  • Page 329 Specifications: 1, 2, 5, 6, 7, 10, 11 ITEM: Lights Headlight Low beam High beam Front fog light Turn signal light Front Rear Position light Brake/tail light License plate light Reversing light High mount stop light Door illumination light Dome light Spot light Center light Rear light...
  • Page 330 SPECIFICATIONS ITEM: Steering Toe-in Camber angle Caster angle ITEM: Capacities (approx.) Coolant Fuel tank Engine oil (replaced with filter) Transmission oil Differential gear oil Front Rear Transfer gear box oil with a transfer switch without a transfer switch Extension case oil 12-4 Front 0 ±...

  • Page 331: Index

    INDEX Symbols “AIR BAG” Light ...2-61 “CRUISE” Indicator Light ...2-62 “ESP OFF” Indicator Light ... 2-59 “ESP” (Electronic Stability Program) Warning Light ...2-59 “ESP” Warning Light ...3-33 “SET” Indicator Light ...2-62 Numerics 4-Speed Automatic Transmission ...3-13 5-Speed Automatic Transmission ...3-11 A/T Selector Position ...2-68 Accelerator Pedal ...3-8 Accessory Socket ...5-66...
  • Page 332 INDEX Cup Holder and Storage Bin ...5-72 Daily Inspection Checklist ...3-2 Daytime Running Light (D.R.L.) Indicator Light ...2-63 Daytime Running Light (D.R.L.) System ...2-78 Door Locks ...2-1 Drive Belt ...7-9 Driver’s Seat Belt Reminder Light ...2-61 Driving Range ...2-68 Electronic Stability Program (ESP®) ...3-31 Emergency Locking Retractor (ELR) ...2-28 Emission Compliance Label (for U.S.A.) ...10-2 Engine Block Heater ...3-10...
  • Page 333 If the Engine Overheats ...8-9 If the Starter Does Not Operate ...8-8 If You Cannot Shift Automatic Transmission Gearshift Lever Out of “P” (PARK) ...3-15 If Your Vehicle Gets Stuck ...4-6 Ignition Key Reminder ...2-1 Ignition Switch ...3-3 Illumination Indicator Light ...2-64 Important Vehicle Design Features To Know ...4-1 Improving Fuel Economy ...4-3 Information Display ...2-67...
  • Page 334 INDEX On-Pavement Driving ...4-4 Open Door Warning Light ...2-62 Outside Rearview Mirrors ...2-17 Overhead Console Box ...5-71 Parking Brake Lever ... 3-7 Pedals ...3-8 Periodic Maintenance Schedule ...7-3 Power Assisted Brakes ...3-29 Power Door Locking System ...2-2 Power Mirror Control ...2-18 Power Steering ...7-24 Power Steering Fluid ...7-24 Power Window Controls ...2-15...
  • Page 335 Tire Chains ...4-7 Tire Changing Tool ...8-1 Tire Inflation Pressure ...7-27 Tire Inspection ...7-28 Tire Pressure Monitoring System (TPMS) ...3-38 Tire Rotation ...7-31 Tire Sidewall Labeling ...7-25 Tire Size ...7-26 Tires ...7-25 Towing a Disabled Vehicle ...8-8 Towing Your Vehicle (recreational towing) ...6-7 Traction Control System ...3-31 Trailer Towing ...6-2 Transfer Position Indicator Light ...2-64...
  • Page 336 INDEX MEMO 13-6 79K21-03E...
  • Page 337 Prepared by June, 2009 Part No. 99011-79K21-03E Printed in Japan TP334 79K21-03E...

This manual is also suitable for:

2011 grand vitara

Table of Contents

Save PDF