Philips LPC213 Series User Manual page 190

Philips Semiconductors
Volume 1
Table 158: Match Control Register (MCR, TIMER0: T0MCR - address 0xE000 4014 and TIMER1: T1MCR - address
0xE000 8014) bit description
Bit Symbol Value
11 PWMMR3S 1
0
12 PWMMR4I 1
0
13 PWMMR4R 1
0
14 PWMMR4S 1
0
15 PWMMR5I 1
0
16 PWMMR5R 1
0
17 PWMMR5S 1
0
18 PWMMR6I 1
0
19 PWMMR6R 1
0
20 PWMMR6S 1
0
31:21 -
15.4.8 PWM Control Register (PWMPCR - 0xE001 404C)
The PWM Control Register is used to enable and select the type of each PWM channel.
The function of each of the bits are shown in
Table 159: PWM Control Register (PWMPCR - address 0xE001 404C) bit description
Bit Symbol Value
1:0 -
2 PWMSEL2 1
0
3 PWMSEL3 1
0
User manual
Description
Stop on PWMMR3: The PWMTC and PWMPC will be stopped and PWMTCR[0] will
be set to 0 if PWMMR3 matches the PWMTC.
This feature is disabled
Interrupt on PWMMR4: An interrupt is generated when PWMMR4 matches the value
in the PWMTC.
This interrupt is disabled.
Reset on PWMMR4: the PWMTC will be reset if PWMMR4 matches it.
This feature is disabled.
Stop on PWMMR4: the PWMTC and PWMPC will be stopped and PWMTCR[0] will
be set to 0 if PWMMR4 matches the PWMTC.
This feature is disabled
Interrupt on PWMMR5: An interrupt is generated when PWMMR5 matches the value
in the PWMTC.
This interrupt is disabled.
Reset on PWMMR5: the PWMTC will be reset if PWMMR5 matches it.
This feature is disabled.
Stop on PWMMR5: the PWMTC and PWMPC will be stopped and PWMTCR[0] will
be set to 0 if PWMMR5 matches the PWMTC.
This feature is disabled
Interrupt on PWMMR6: an interrupt is generated when PWMMR6 matches the value
in the PWMTC.
This interrupt is disabled.
Reset on PWMMR6: the PWMTC will be reset if PWMMR6 matches it.
This feature is disabled.
Stop on PWMMR6: the PWMTC and PWMPC will be stopped and PWMTCR[0] will
be set to 0 if PWMMR6 matches the PWMTC.
This feature is disabled
Reserved, user software should not write ones to reserved bits. The value read from
a reserved bit is not defined.
Description
Reserved, user software should not write ones to reserved bits. The value read from
a reserved bit is not defined.
Selects double edge controlled mode for the PWM2 output.
Selects single edge controlled mode for PWM2.
Selects double edge controlled mode for the PWM3 output.
Selects single edge controlled mode for PWM3.
Rev. 01 — 24 June 2005
Table 159.
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
UM10120
Chapter 15: PWM
Reset
value
0
0
0
0
0
0
0
0
0
0
NA
Reset
value
NA
0
0
190