Connection Procedure, Frames R6 - ABB ACS560 Quick Installation And Start-Up Manual

Connection procedure, frames R6...R8
18 EN - Quick installation and start-up guide
See page 71. If the drive will be connected on a corner-grounded TN syste
￭ Connection procedure, frames R5...R8
sure you have disconnected the EMC filter. See page 71.
WARNING!
If the drive will be connected on an IT (ungrounded) system, make sure you have
disconnected the EMC Filter and Varistor (VAR). See
1. Attach the residual voltage warning sticker next to the control board.
1. Attach the residual voltage warning sticker next to the control board.
2. Remove the side plates of the cable box as follows:
86 Electrical installation
86 Electrical installation 86 Electrical installation
2. Remove the side plates of the cable box as follows:
•
• Remove the retaining screws.
Connection procedure, frames R6...R8 Connection procedure, frames R6...R8
• Slide the walls out.
•
WARNING! If the drive will be connected on an IT (ungrounded) system,
EN
make sure you have disconnected the EMC filter and ground-to-phase varistor.
1
See page 71. If the drive will be connected on a corner-grounded TN system, make See page 71. If the drive will be connected on a corner-grounded TN system, make
See page 71. If the drive will be connected on a corner-grounded TN system, make
HI
sure you have disconnected the EMC filter. See page 71. sure you have disconnected the EMC filter. See page 71.
sure you have disconnected the EMC filter. See page 71.
1. Attach the residual voltage warning sticker next to the control board. 1. Attach the residual voltage warning sticker next to the control board. 1. Attach the residual voltage warning sticker next to the control board.
2. Remove the side plates of the cable box as follows: 2. Remove the side plates of the cable box as follows:
2. Remove the side plates of the cable box as follows:
• Remove the retaining screws. •
• Slide the walls out. •
1
1 1
3. Remove the shroud on the power cable terminals by releasing the clips
screwdriver and pulling the shroud out.
3. Remove the shroud on the power cable terminals by releasing the clips with a screwdriver
and pulling the shroud out.
4. Knock out holes in the shroud for the cables to be installed.
3. Remove the shroud on the power cable terminals by releasing the clips with a
3. Remove the shroud on the power cable terminals by releasing the clips with a 3. Remove the shroud on the power cable terminals by releasing the clips with a
4. Knock out holes in the shroud for the cables to be installed.
screwdriver and pulling the shroud out. screwdriver and pulling the shroud out.
5. Frame R8 only: If you install parallel cables, also knock out holes in the lower shroud
5. Frames R8: If you install parallel cables, also knock out holes in the low
4. Knock out holes in the shroud for the cables to be installed. 4. Knock out holes in the shroud for the cables to be installed.
4. Knock out holes in the shroud for the cables to be installed.
for the cables to be installed.
for the cables to be installed.
5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud
5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud 5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud
for the cables to be installed. for the cables to be installed.
3
3 3
3
3
Motor cable
6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
WARNING! If the drive will be connected on an IT (ungrounded) sys
make sure you have disconnected the EMC filter and ground-to-phas
Remove the retaining screws.
Connection procedure, frames R6...R8
Slide the walls out.
WARNING! If the drive will be connected on an IT (ungrounded) system, WARNING! If the drive will be connected on an IT (ungrounded) system,
make sure you have disconnected the EMC filter and ground-to-phase varistor.
make sure you have disconnected the EMC filter and ground-to-phase varistor.
Remove the retaining screws. • Remove the retaining screws.
• Slide the walls out.
Slide the walls out.
2 2
screwdriver and pulling the shroud out.
for the cables to be installed.
3
3
3
2
2
2
Frame R8
R8...R8
R8...R8
4 4
4 5 5
EMC filter (page 28).
R8...R8
5
4
R8...R8
5