ABB ACS560 Quick Installation And Start-Up Manual page 132

Connection procedure, frames R6...R8
132 HI -त् व रित इं स ् ट ाले श न और स् ट ार् ट -अप गाइड
See page 71. If the drive will be connected on a corner-grounded TN syste
￭ कने क ् श न प् र क् र िया, फ् र े म R5...R8
sure you have disconnected the EMC filter. See page 71.
चे त ावनी!
यदि ड् र ाइव को एक IT (अनग् र ाउं ड ड) सिस् ट म से कने क ् ट किया जाएगा, तो सु न िश् च ित करे ं कि आपने
EMC फिल् ट र और वे र िस् ट र (VAR) को डिस् क ने क ् ट कर दिया है । दे ख े ं
1. Attach the residual voltage warning sticker next to the control board.
1. नियं त ् र ण बोर् ड के बगल मे ं अवशे ष वोल् ट े ज चे त ावनी स् ट ीकर को सं ल ग् न करे ं ।
2. Remove the side plates of the cable box as follows:
86 Electrical installation
86 Electrical installation 86 Electrical installation
2. के ब ल बॉक् स के साइड प् ल े ट ् स को निम् न ानु स ार निकाले ं :
•
• रिटे न िं ग पे ं च ों को निकाले ं ।
Connection procedure, frames R6...R8 Connection procedure, frames R6...R8
• दीवारों को बाहर की तरफ खिसकाएं ।
•
WARNING! If the drive will be connected on an IT (ungrounded) system,
EN
make sure you have disconnected the EMC filter and ground-to-phase varistor.
1
See page 71. If the drive will be connected on a corner-grounded TN system, make See page 71. If the drive will be connected on a corner-grounded TN system, make
See page 71. If the drive will be connected on a corner-grounded TN system, make
HI
sure you have disconnected the EMC filter. See page 71. sure you have disconnected the EMC filter. See page 71.
sure you have disconnected the EMC filter. See page 71.
1. Attach the residual voltage warning sticker next to the control board. 1. Attach the residual voltage warning sticker next to the control board. 1. Attach the residual voltage warning sticker next to the control board.
2. Remove the side plates of the cable box as follows: 2. Remove the side plates of the cable box as follows:
2. Remove the side plates of the cable box as follows:
• Remove the retaining screws. •
• Slide the walls out. •
1
1 1
3. Remove the shroud on the power cable terminals by releasing the clips
screwdriver and pulling the shroud out.
3. एक पे ं च कस के साथ क् ल िप निकाल कर और ढक् क न को बाहर खीं च कर पावर के ब ल टर् म िनलों पर ढक् क न
को निकाले ं ।
4. Knock out holes in the shroud for the cables to be installed.
3. Remove the shroud on the power cable terminals by releasing the clips with a
3. Remove the shroud on the power cable terminals by releasing the clips with a 3. Remove the shroud on the power cable terminals by releasing the clips with a
4. स् थ ापित की जाने वाली के ब लों के लिए ढक् क न मे ं छे द करे ं ।
screwdriver and pulling the shroud out. screwdriver and pulling the shroud out.
5. के व ल फ़् र े म R8: यदि आप समानां त र के ब लों को स् थ ापित करते है ं , तो स् थ ापित की जाने वाली के ब लों के लिए
5. Frames R8: If you install parallel cables, also knock out holes in the low
4. Knock out holes in the shroud for the cables to be installed. 4. Knock out holes in the shroud for the cables to be installed.
4. Knock out holes in the shroud for the cables to be installed.
निचले ढक् क न मे ं भी छे द करे ं ।
for the cables to be installed.
5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud
5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud 5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud
for the cables to be installed. for the cables to be installed.
3
3 3
3
3
मोटर के ब ल
6. रबर ग् र ोमे ट मे ं एक पर् य ाप् त छे ट काटे ं । ग् र ोमे ट को के ब ल पर खिसका दे ं ।
WARNING! If the drive will be connected on an IT (ungrounded) sys
make sure you have disconnected the EMC filter and ground-to-phas
Remove the retaining screws.
Connection procedure, frames R6...R8
Slide the walls out.
WARNING! If the drive will be connected on an IT (ungrounded) system, WARNING! If the drive will be connected on an IT (ungrounded) system,
make sure you have disconnected the EMC filter and ground-to-phase varistor.
make sure you have disconnected the EMC filter and ground-to-phase varistor.
Remove the retaining screws. • Remove the retaining screws.
• Slide the walls out.
Slide the walls out.
2 2
screwdriver and pulling the shroud out.
for the cables to be installed.
3
3
3
2
2
2
फ़् र े म R8
R8...R8
R8...R8
4 4
4 5 5
EMC फ़ ि ल् ट र ( पृ ष ् ठ 142).
R8...R8
5
4
R8...R8
5