Actual Signals; Ch0 Datasets In - ABB ACS800 Series Firmware Manual

66
No. Name/Value
02.37 2. LATEST WARNING
02.38 3. LATEST WARNING
02.39 4. LATEST WARNING
02.40 5. LATEST WARNING
02.41 LIMIT WORD INV
02.42 MTR ACCELERATION

03 ACTUAL SIGNALS

03.01 DRAW SETPOINT
03.02 TOTAL DRAW TRIM
03.03 DANCER LOAD SETPT
03.04 DANCER LOAD REF
03.05 DANCER REG OUTPUT
03.06 DANCER POSITION
03.07 TENSION SETPOINT
03.08 TENSION REFERENCE
03.09 TENSION REG OUTPT
03.10 TENSION ACTUAL
03.11 TEN CALC TORQ REF
03.12 CALC TTL INERTIA
03.13 ROLL DIAMETER
03.14 % FULL ROLL
03.15 PACK STATUS BITS
03.16 PSEUDO SPD OUT
03.17 PSEUDO SPD IN
03.18 FRICTION COMP
03.19 PSEUDO OUT SCLD

06 CH0 DATASETS IN

06.01 DATASET 1 WORD 1
06.02 DATASET 1 WORD 2
06.03 DATASET 1 WORD 3
Actual signals and parameters
Description
Fieldbus code of the 2nd latest warning.
Fieldbus code of the 3rd latest warning.
Fieldbus code of the 4th latest warning.
Fieldbus code of the 5th latest warning.
A 16-bit data word. See Table 19
The dv/dt of 01.02 MOTOR SPEED FILT.
Control Program signals for monitoring of the process
Percentage of speed adjustment due to the draw reference (Core
speed match reference).
Total percentage of speed adjustment for progressive draw systems.
Dancer cylinder setpoint from an analog input. Used for setting
desired web tension.
Dancer cylinder reference. Comprised of
SETPT, tension taper settings and stall tension settings.
Percentage output of the dancer's PI regulator.
Position of travel for the dancer arm.
Tension setpoint from analog input.
Tension reference. Comprised of
taper settings and stall tension settings.
Percentage output of the tension's PI regulator.
Tension actual as measured by the loadcell.
Torque reference calculated from the
and 03.13 ROLL DIAMETER.
Total calculated section inertia.
Actual roll diameter.
When dancer / tension test control active.
Percentage of full roll (increases as roll builds
DIAMETER / 65.02 MAX ROLL DIAMETER
A 16-bit data word. See Table 8
02.02 SPEED REF 3 / 25.02
Lead macro.
Speed feedback from measuring wheel (see
Used for Winder – Lead macro.
The total frictional compensation added to
REF.
03.16 PSEUDO SPD OUT scaled for use by follower. 20000
corresponds to 11.05 EXT REF1 MAXIMUM.
Words for monitoring data received from fieldbus.
A 16-bit data word. See Table 3
A 16-bit data word. Speed reference (see
A 16-bit data word. See Table 4
on page 160.
03.03 DANCER LOAD
03.07 TENSION SETPOINT, tension
03.07 TENSION REFERENCE
up).03.13
on page 153.
SPEED MULTIPLIER. Used for Winder –
67.01 WEB SPD INPUT).
03.11 TEN CALC TORQ
on page 149.
11.03 EXT1 REF SELECT). 1 = 1
on page 150.
FbEq
1 = 1
1 = 1
1 = 1
1 = 1
1 = 1
1 = 1 rpm/s
100 = 1%
100 = 1%
10 = 1%
10 = 1%
10 = 1%
10 = 1 mm
10 = 1 inch
10 = 1 N
10 = 1 lb
10 = 1 N
10 = 1 lb
10 = 1%
10 = 1 N
10 = 1 lb
10 = 1 Nm
10 = 1 lbft
10 = 1 kgm
2
10 = 1 lbft
10 = 1 mm
10 = 1 inch
ROLL 10 = 1%
1 = 1 rpm
1 = 1 rpm
200 = 1%
1 = 1 Nm
1 = 1 lbft
1 = 1
1 = 1
1 = 1
2