Sharp MX-M550U Service Manual page 86

SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START.
0.TRAY SELECT 1
2.EXP LEVEL 1
3.AUTO 50 4.1.0
6.3.0 50 7.4.0
9.AUTO(H) 50
12.3.0(H) 50
Select other than 0 - 2,
and press [START] key.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE),INPUT VALUE 0-99, AND PRESS
START.
4.1.0
Select 1, Press [START] key.
and press
[START] key.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). NOW PRINTING.
Select 0, and press [START] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(FINE). SELECT 1-6, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
Select 2, and press
[START] key.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). SELECT 3-14, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0
6.3.0 7.4.0
9.AUTO(H) 10.1.0(H)
12.3.0(H) 13.4.0(H)
Item
0 TRAY SELECT Paper feed tray selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3 AUTO Auto
4 1.0 Exposure level 1
5 2.0 Exposure level 2
6 3.0 Exposure level 3
7 4.0 Exposure level 4
8 5.0 Exposure level 5
9 AUTO (H) Auto (Half-tone)
10 1.0 (H) Exposure level 1 (Half-tone)
11 2.0 (H) Exposure level 2 (Half-tone)
12 3.0 (H) Exposure level 3 (Half-tone)
13 4.0 (H) Exposure level 4 (Half-tone)
14 5.0 (H) Exposure level 5 (Half-tone)
3) Using the numeric keypad, select the number that corresponds
to the adjustment item. Choose from numbers 3 to 8 (14).
* Auto mode
* Manual mode (print density adjustment level)
For manual mode, select the number that corresponds to the
print density level (1 to 5). (Choose from numbers (4 to 8) (10-
14)).
4) Press the Start key.
5) Press the Start key. (A copy is created.)
1.PRINT START
50 5.2.0 50
50 8.5.0 50
10.1.0(H) 50 11.2.0(H)
13.4.0(H) 50 14.5.0(H)
Press [SYSTEM SETTINGS]
key.
Press [SYSTEM SETTINGS]
key, or terminate copying.
Press [START] key, or press
[SYSTEM SETTINGS] key.
Press [START] key, or press
[SYSTEM SETTINGS] key.
5.2.0
8.5.0
11.2.0(H)
14.5.0(H)
Setting
range
0 – 99
MX-M700N ADJUSTMENTS 6 – 35
[Binary mode]
(Copied image reference density)
Original
1
50
1
50
Copy
50
1
If the copied test chart (UKOG-0162FCZZ) image includes a
background copy of patch 6 rather than patch 5, adjust all-
copy mode to the image density level specified above.
[Half-tone mode]
(Copied image reference density)
1
Original
1
1
Copy
Default
1
50
The copied test chart (UKOG-0162FCZZ) image includes a
background copy of patch 2 rather than patch 1.
If the print density is not at an acceptable level, do the follow-
ing steps.
6) Adjust the copy density by entering an appropriate value
through the numeric keypad.
A larger value provides higher density.
7) Press the P or Start key.
This applies the adjustment value.
Pressing the Start key starts copy operation as well as apply-
ing the adjustment value.
8) Check the printed image density.
Repeat steps 6 to 8 until an acceptable image density is
obtained.
GRAY CHART
R
2 3 4 5 6 7
GRAY CHART
R
2 3 4 5 6 7
GRAY CHART
R
2 3 4 5 6 7
GRAY CHART
R
2 3 4 5 6 7
8 9 10 W
Lot No. 01A
8 9 10 W
Lot No. 01A
8 9 10 W
Lot No. 01A
8 9 10 W
Lot No. 01A