Sharp MX-M550U Service Manual page 136

4) Press the [START] key.
1 AE MODE
2 AE STOP MODE
(COPIER)
3 AE STOP MODE
(SCANNER)
4 AE STOP MODE (FAX)
Mode Set value
AE mode 1 Image quality priority mode
(Normal mode) * Gamma is
sharp to provide high contrast
images.
2 Toner consumption priority
mode * Gamma is mild to
provide low contrast images.
AE fixed 0 AE fixed OFF
mode
1 AE fixed ON
AE fixed OFF: The automatic density (exposure) control is performed
in real time. (The density level is changed in real time
according to the document pattern.)
AE fixed ON: The density at the lead edge of the document is
scanned, and the overall density (exposure) level is
determined according to the scanned density level.
(Overall density level fixed)
SIMULATION 46-19
EXP.MODE SETUP. SELECT 1-2, AND PRESS START.
1.AE MODE 1
2.AE STOP MODE(COPIER)
3.AE STOP MODE(SCANNER)0
4.AE STOP MODE(FAX)
46-20
Purpose Adjustment
Function (Purpose) Used to adjust the copy density correction
in the SPF copy mode for the document
table copy mode. The adjustment is made
so that the copy density becomes the same
as that of the document table copy mode.
Section SPF
Operation/Procedure
(Adjustment mode selection)
1) Select the number that corresponds to the mode for which to
make adjustments with 10-key.
SPF front frame side (Front surface copy), SPF rear frame
side (Front surface copy), SPF (Back surface copy) (Select
one of 3 - 5.)
2) Press the [START] key.
(Copy density level adjustment)
1) Enter the density correction value with 10-key.
2) Press the [P] or [START] key.
(Copy condition setting in this simulation)
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
AE mode
AE fixed mode (Copier)
AE fixed mode (Scanner)
AE fixed mode (FAX)
Item
(COPIER)
(SCANNER
1
0
MX-M700N SIMULATION 7 – 42
0 TRAY SELECT
Default
2
1 PRINT START
2 EXP LEVEL
1
0
/FAX)
3 SPF (FRONT)
4 SPF (REAR)
5 DSPF
• Set value - 128 is added to the shading adjustment value (SIM
46-17).
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START.
0. TRAY SELECT
2. EXP LEVEL
3. SPF(FRONT)
4. SPF(REAR)
5. DSPF
46-21
Purpose
Function (Purpose) Used to set the auto mode operation speci-
Section
Operation/Procedure
1) Select the adjustment item SCANNER EXP. LEVEL with 10-
key.
2) Press the [START] key.
3) Enter the image density adjustment value.
4) Press the [P] or [START] key.
NOTE: When this simulation is performed to adjust the scan image
densities, all the image densities in all the scan modes are
changed to the image density level set with this simulation.
That is, the image densities set with SIM 46-22, 23, 24, 25,
and 45 are changed to the image density level set with this
simulation.
0 SCANNER EXP.
LEVEL
Item Content
Paper feed tray
selection
1: TRAY1
2: TRAY2
3: TRAY3
4: TRAY4
5: Manual feed
6: Side LCC
Print start (Default)
Exposure level
selection
3: Exposure level 1.0
4: Exposure level 1.5
5: Exposure level 2.0
6: Exposure level 2.5
7: Exposure level 3.0
8: Exposure level 3.5
9: Exposure level 4.0
10: Exposure level 4.5
11: Exposure level 5.0
SPF (front)
(front frame side)
SPF (front)
(rear frame side)
DSPF
(Back surface)
1 1. PRINT START
1
128
128
128
Adjustment
fications in each mode (copy, scan, FAX).
—
Item
Image density level
Setting
Default
range
— —
— —
— —
0 - 255 128
1
Setting
Default
range
0 - 99 50