Sharp MX-M550U Service Manual page 164

66-36
Purpose Operation test/Check
Function (Purpose) Used to check interface between MFPC
controller and MDMC. (Check of the data
line or the command line)
Section FAX
Operation/Procedure
1) Enter the number corresponding to the check mode with 10-
key.
MFPC ← MDMC
1
MFPC → MDMC
2
MFPC ← MDMC
3
MFPC → MDMC
4
MFPC ← MDMC
5
MFPC → MDMC
6
MFPC ← MDMC
7
MFPC → MDMC
8
2) Press [START] key.
When check is completed normally, "OK" is displayed. Incase of an
error, "NG" is displayed.
When check is "repeat," the operation is continued until the result is
NG or [SYSTEM SETTINGS] key is pressed.
SIMULATION 66-36
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
1. MFPC<-MDMC(DATA once)
2. MFPC->MDMC(DATA once)
3. MFPC<-MDMC(DATA repeat)
4. MFPC->MDMC(DATA repeat)
5. MFPC<-MDMC(CMD once)
6. MFPC->MDMC(CMD once)
7. MDPC<-MDMC(CMD repeat)
8. MFPC->MDMC(CMD repeat)
66-39
Purpose Setting
Function (Purpose) Used to set the destination specifications.
Section FAX
Operation/Procedure
1) Enter the number corresponding to the destination.
2) Press [START] key.
SIMULATION 66-39
FAX DESTINATION SETUP.
SELECT 1-6, AND PRESS START
0. NO DESTINATION
1. JAPAN
2. U.S.A./CANADA
3. EUROPE
4. AUSTRALIA
5. CHINA
6. ASIA&OTHERS
Date line once only
Date line once only
Data line repeat
Data line repeat
Command line once only
Command line once only
Command line repeat
Command line repeat
1
MX-M700N SIMULATION 7 – 70
66-42
Purpose
Function (Purpose) Reloads the PIC program installed to FAX
Section
Operation/Procedure
NOTE: Before processing, permit writing to the FAX PROGRAMA.
(Cancel the write protection)
1) Press [1] key to carry out the writing. Press [2] key to cancel.
2) If the operation is normally completed, "OK" is displayed.
When the error occurs, "NG" is displayed.
(Cause of the ERROR)
* State is write-protection.
* PIC is not mounted.
* Access trouble to PIC
SIMULATION 66-42
PIC PROGRAM RELOAD
ARE YOU SURE?
1.YES
2.NO
66-43
Purpose
1
Function (Purpose) Setting of the PIC adjustment value
Section
Operation/Procedure
NOTE: Before processing, permit writing to the FAX PROGRAMA.
(Cancel the write protection)
1) Present setting is highlight-displayed on the side of item.
2) Use the numeric keys to enter the adjustment value. Press the
[P] key to memorizes the input value.
3) Press [1] to writing the adjustment value collectively to PIC that
installed to the FAX BOX.
* If the operation is normally completed, "WRITING OK" is dis-
played. When the error occurs, "NG" is displayed.
SIMULATION 66-43
PIC ADJUSTMENT VALUE WRITING.
ENABLE WRITE PIN (for FAX PROGRAM ROM)
SELECT 0-12 AND PRESS START.
0. WRITING for PIC
2.
ci_cycle_min
5.
ci_count
8.
fnet_range
11.
poff_time
Setting
BOX.
FAX
Adjustment/Setup
FAX
1.
ci_level_judge
10 3. 107 4. ci_range
ci_cycle_max
3 6. 8 7.
cidetect fnet_level_judge
3 9. 100 10.
fnet_time_out
3 12. 3
mswon_level_judge
1
1
22
5
1
3
fnet_count