Sharp MX-M550U Service Manual page 159

66-10
Purpose User data output/Check (Display/Print)
Function (Purpose) Used to clear all data of the image memory
(memory send/receive). The confidential
data are also cleared at the same time.
(Only when FAX is installed)
Section FAX
Operation/Procedure
1) Select YES/NO of image memory clear with 10-key.
1 YES Image memory clear is executed.
2 NO Not cleared.
2) Press the [START] key.
The SRAM image data management table and image data in the
Flash ROM area and HD (except for filing images) are cleared.
SIMULATION 66-10
IMAGE MEMORY CLEAR
ARE YOU SURE?
1. YES
2. NO
66-11
Purpose Operation test/Check
Function (Purpose) Used to check the output operation of FAX
G3 mode 300bps. (Used to check the oper-
ation of MODEM.) Send level: Max. (Only
when FAX is installed)
Section FAX
Operation/Procedure
1) Enter the number corresponding to the output mode with 10-
key.
2) Press the [START] key.
The output is delivered at the max. send level.
1 NO SIGNAL No signal
2 11111 11111
3 11110 11110
When the number is entered during execution, the kind of signal
can be changed.
When [SYSTEM SETTINGS] key is pressed during execution, the
operation is stopped.
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX)
START.
1. NO SIGNAL 2. 11111
5. 010101 6. 00001
66-12
Purpose Operation test/Check
Function (Purpose) Used to check the output operation of FAX
G3 mode 300bps. (Used to check the oper-
ation of MODEM.) An output is send at the
send level set by the soft switch. (Only
when FAX is installed)
Section FAX
Operation/Procedure
1) Enter the number corresponding to the output mode with 10-
key.
2) Press the [START] key.
The output is delivered at the send level set with the soft switch.
4 00000 00000
5 010101 010101
6 00001 00001
SELECT 1-6, AND PRESS
3. 11110 4. 00000
MX-M700N SIMULATION 7 – 65
1 NO SIGNAL
2 11111
3 11110
When the number is entered during execution, the kind of signal
can be changed.
When [SYSTEM SETTINGS] key is pressed during execution, the
operation is stopped.
SIMULATION 66-12
300bps SIGNAL OUTPUT.(SOFT SW.)
START.
1. NO SIGNAL
5. 010101
66-13
Purpose
Function (Purpose) Used to enter (set) the number of FAX dial
1
Section
Operation/Procedure
1) Enter the dial number with 10-key.
Use 10-key, [*] key, and [#] key to enter the number. The upper
limit is 20 digits.
When [CLEAR] key is pressed, the mode returns to the initial
state.
2) Press the [START] key.
SIMULATION 66-13
DIAL TEST NUMBER SETTING.
INPUT NUMBER AND PRESS START.
0123456789*#01234567
66-14
Purpose
Function (Purpose) Used to set the make time in the FAX pulse
1
Section
Operation/Procedure
1) Enter 0 with 10-key.
2) Press the [START] key.
The dial signal is outputted.
(Dial pulse make time setting)
1) Enter 1 with 10-key.
2) Press the [START] key.
3) Enter the set value with 10-key.
4) Press the [START] key.
0 EXECUTE
1 MAKE TIME
The dial signal is sent with the set value + 29ms.
When [SYSTEM SETTINGS] key is pressed during execution, the
operation is stopped.
No signal 4 00000
11111 5 010101
11110 6 00001
SELECT 1-6, AND PRESS
2. 11111 3. 11110 4. 00000
6. 00001
Setting
signal output test. (The dial number set by
this simulation is outputted when the dial
signal output test is made by SIM 66-14 -
16. ) (Only when FAX is installed)
FAX
0-9:[0-9], *:[*], #:[#]
Setting/Operation test/Check
dial mode (10pps) and to test the dial signal
output. (The dial number signal set by SIM
66-13 is outputted.) Used to check troubles
in dialing and to check the operation. (Only
when FAX is installed)
FAX
Execution
Dial pulse make time setting (0 - 15)
00000
010101
00001
1