Sharp MX-M550U Service Manual page 133

3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1 TRAY1
2 TRAY2 TRAY2
3 TRAY3 TRAY3
4 TRAY4 TRAY4
5 BPT Manual paper feed
6 LCC Side LCC
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0
6.3.0 50 7.4.0
9.AUTO(H) 50 10.1.0(H)
12.3.0(H) 50 13.4.0(H)
46-15
Purpose Adjustment
Function (Purpose) Used to adjust the print density in the FAX
mode (each super fine mode). (Only when
FAX is installed.)
Section —
Operation/Procedure
1) Select the number corresponding to one of the following
adjustment items with 10-key. (Select one of 3 - 14.)
* Normal mode (Print density adjustment level)
* Normal mode (Print density adjustment level) (Half-tone
mode)
* Auto mode
* Auto mode (Half-tone mode)
2) Press the [START] key.
3) Enter the print density level with 10-key.
Item
0 TRAY SELECT Paper feed tray
selection
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level
selection
3 AUTO Auto
4 1.0 Exposure level 1
5 2.0 Exposure level 2
6 3.0 Exposure level 3
7 4.0 Exposure level 4
8 5.0 Exposure level 5
9 AUTO (H) Auto (Half-tone)
10 1.0 (H) Exposure level 1
(Half-tone)
11 2.0 (H) Exposure level 2
(Half-tone)
12 3.0 (H) Exposure level 3
(Half-tone)
13 4.0 (H) Exposure level 4
(Half-tone)
14 5.0 (H) Exposure level 5
(Half-tone)
4) Press the [P] or [START] key.
The adjustment value is set.
50 5.2.0 50
50 8.5.0 50
50 11.2.0(H) 50
50 14.5.0(H) 50
Setting
range
0 - 99
MX-M700N SIMULATION 7 – 39
When [START] key is pressed, printing is performed and the
adjustment value is set simultaneously.
Check the density of print image.
Normal display
ERROR display
To select paper (paper feed tray), perform the following procedures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
1 TRAY1
2 TRAY2
1 3 TRAY3
4 TRAY4
5 BPT
6 LCC
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and
copying is performed.
SIMULATION 46-15
EXP.LEVEL SETUP FAX(SUPER FINE).SELECT 0-14,AND PRESS
START.
0.TRAY SELECT
2.EXP LEVEL
3.AUTO
6.3.0
9.AUTO(H)
12.3.0(H)
Default
50
Door open
Jam
Paper empty
TRAY1
TRAY2
TRAY3
TRAY4
Manual paper feed
Side LCC
1 1.PRINT START
1
50 4.1.0 50 5.2.0
50 7.4.0 50 8.5.0
50 10.1.0(H) 50
50 13.4.0(H) 50
NOW PRINTING.
DOOR OPEN.
JAM
PAPER EMPTY.
1
50
50
11.2.0(H) 50
14.5.0(H) 50