Sharp MX-M550U Service Manual page 154

63-2
Purpose Adjustment
Function (Purpose) Used to execute shading.
Section Optical (Image scanning)
Operation/Procedure
1) Enter the number corresponding to the shading mode to be
executed.
1 OC SHADING OC analog level correction and shading
correction (Document table mode)
2 DSPF DSPF analog level correction and shading
SHADING correction (SPF mode)
2) Press the [START] key.
During execution, "EXECUTING" is displayed. When execution is
completed normally, "COMPLETED" is displayed.
SIMULATION 63-2
SHADING EXECUTION. SELECT1-2, AND PRESS START.
1. OC SHADING
2. DSPF SHADING
63-7
Purpose Adjustment
Function (Purpose) Used to adjust the white plate scan start
position for shading. (Document table
mode)
Section Scanner (Exposure)
Operation/Procedure
1) Enter 1 with 10-key.
2) Press the [START] key.
3) Enter the adjustment value with 10-key. (1count = 0.5mm)
4) Press the [START] key.
When a shading error occurs, this adjustment value is
changed.
Item
1 CCD CCD scan
SIMULATION 63-7
SHADING POSITION ADJUSTMENT. PRESS START.
1. CCD 0
64
64-1
Purpose Operation test/Check
Function (Purpose) Used to check the operation of the printer
section (self-print operation), (The print pat-
tern, the paper feed mode, the print mode,
the print quantity, and the density can be
optionally set.)
Section —
Operation/Procedure
(Various print patterns output) (Table 1)
1) Select PRINT PATTERN with 10-key.
2) Enter the number corresponding to the print pattern to be
printed with 10-key.
3) Press the [START] key.
4) Select PRINT START with 10-key.
1
Setting
Default
range
1 - 16 6
1
MX-M700N SIMULATION 7 – 60
5) Press the [START] key.
(Print condition setting in this simulation)
* To select paper (paper feed tray), perform the following proce-
dures.
1) Select TRAY SELECT with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
* To adjust the print density, perform the following procedures.
1) Select DENSITY with 10-key.
2) Enter the adjustment value with 10-key.
3) Press the [START] key.
* To set the print quantity, perform the following procedures.
1) Select MULTI with 10-key.
2) Enter the print quantity with 10-key.
3) Press the [START] key.
* To set the print quality mode, perform the following procedures.
1) Select MODE with 10-key.
2) Enter the number corresponding to the print quality mode with
10-key.
3) Press the [START] key.
* To set the print level, perform the following procedures.
1) Select LEVEL with 10-key.
2) Enter the adjustment value with 10-key.
3) Press the [START] key.
NOTE: In some print patterns, changing the level may not change
the picture quality.
* To set duplex/simplex print, perform the following procedures.
1) Select DUPLEX with 10-key.
2) Enter the number corresponding to the operation mode with
10-key.
3) Press [START] key.
(Table 1)
0 TRAY SELECT
1. TRAY1
2. TRAY2
3. TRAY3
4. TRAY4
5. BPT
6. LCC
1 PRINT START
2 PRINT PATTERN
3 DENSITY
4 MULTI
5 MODE
1. STANDARD
2. SMOOTHING
3. TONER SAVE
4. HALF TONE
5. SMOOTHING + TONER
SAVE
6. SMOOTHING + HALF TONE
7. TONER SAVE + HALF
TONE
8. SMOOTHING + TONER
SAVE+ HALF TONE
6 LEVEL
7 DUPLEX
1. NO
2. YES
Paper feed tray
1: Tray 1
2: Tray 2
3: Tray 3
4: Tray 4
5: Manual feed
6: LCC
Print execution (Printing of the
set data is executed.)
Print pattern (Note 1)
Graphic density (Valid only when
No. 79, 80 or 84 is selected.)
Number of print
Print mode
1. Standard
2. Smoothing ON
3. Toner save ON
4. Half tone ON
5. Smoothing + toner save
6. Smoothing + half tone
7. Toner save + half tone
8. Smoothing + toner save + half
tone
Parameter of print image
process: (1 -5)
Duplex
1 : Simplex
2 : Duplex