Advertisement
Front Panel/Remote Commander J
a
[2]
POWER switch
Turns the power on and off.
Cassette compartment
Insert a cassette with the window side up and the safety
tab facing you.
COUNTER buttons
MODE: Selects the counter indication in the display
window among the linear counter (tape running time),
absolute time, elapsed time of the selection, and total
remaining time of the tape. Each time you press the
button, the indication changes sequentially.
RESET: Resets the linear counter to "Om 00s".
FADER button
Press to fade in or fade out during recording or playback.
REPEAT button
Press to play a desired portion repeatedly. Each time you
press the button, the indication changes as follows:
REPEAT 1 > REPEAT ALL > Nothing
Music select buttons
Numeric buttons (0 - 9): Designate the desired program
number to be played back before starting playback.
CLEAR: Use to cancel the program number which has
been mistakenly entered.
MUSIC SCAN: Use this feature to listen to the beginning
of each selection successively.
SKIP PLAY button
Press to activate the skip ID code function. The portion
of the tape previously marked will be skipped.
REC LEVEL (recording level) controls
Adjust the recording level for the analog input signals. The
outer knob controls the L (left) channel leve} and the inner
knob the R (right) channel level. The knobs can be
adjusted together.
When recording digital signals, it is not necessary to
adjust the recording level.
INPUT selector
Set according to the signai to be recorded.
ANALOG: For recording from the equipment connected to
the LINE IN jacks.
OPTICAL: For recording from the equipment connected to
the DIGITAL IN (OPTICAL) jack.
COAXIAL: For recording from the equipment connected to
the DIGITAL IN (COAXIAL) jack.
PHONES (Headphones) jack and LEVEL controls
The LEVEL controls adjust the headphones volume level.
[#f] MARGIN RESET button
Press to reset the margin of peak level.
END ID buttons
WRITE: Press to write the ID signifying the end of playback
or recording.
ERASE: Press to erase the end ID.
SKIP ID buttons
WRITE: Press at the beginning of the portion you may wish
to skip later. A skip ID will be written from the point where
you pressed this button.
ERASE: Press to erase the nearest skip ID which is before
the current position.
START ID buttons
AUTO: Press to turn on and off the AUTO indicator. When
the AUTO indicator is lit, the start ID will automatically be
written during recording. When the AUTO indicator is not
lit, press START ID WRITE at the point where you want
to write a start ID.
WRITE: Press to write the start ID at the desired point
during recording or playback.
ERASE: Press to erase a start ID. When a start ID anda
program number are written on the tape, both codes are
simultaneously erased by pressing this button.
RENUMBER: Press to renumber all programs on the tape.
When only the start IDs are written, pressing this button
will insert the proper program numbers beginning with
"4 The tape will rewind and start from the beginning to
accomplish this function.
[| Tape operating buttons
(stop): Press to stop recording or playback.
> (play): Press to play back the tape.
ine (recording): Press to start recording. After pressing this
button, press Hor(>.
palise (Pause): Press to stop fora moment during recording
or playback. To restart recording or playback, press this
button again or press [>.
If the unit is left in the pause mode for about 10 minutes,
it will be automatically released and the deck will enter
the stop mode. To restart recording or playback from the
stop mode, press REC or[> respectively.
rec mure(record muting): Inserts a sound-muted portion
(space).
KKK, >> (AMS): Press to locate the beginning of the
selection during the playback.
<4, PP (rewind/review, fast-forward/cue): in the stop
mode, press to rewind/fast-forward the tape. During
playback, press to rewind or fast-forward the tape while
listening to the sound.
Advertisement
