ABB ACS550-02 User Manual page 82

80
Group 10: Start/Stop/Dir
This group:
• Defines external sources (
and direction changes.
• Locks direction or enables direction control.
To select between the two external locations use the next group (parameter 1102).
Code Description
1001 EXT1 COMMANDS
Defines external control location 1 (
0 = NOT SEL – No external start, stop and direction command source.
1 = 1 – Two-wire Start/Stop.
DI
• Start/Stop is through digital input
• Parameter 1003 defines the direction. Selecting 1003 = 3 (request) is the same as 1003 = 1 (fwd).
2 = 1, 2 – Two-wire Start/Stop, Direction.
DI
• Start/Stop is through digital input
• Direction control (requires parameter 1003 = 3 (request)) is through digital input
( 2 activated = Reverse; de-activated = Forward).
DI
3 = 1 , 2 – Three-wire Start/Stop.
DI P P
• Start/Stop commands are through momentary push-buttons (the
• Start is through a normally open push-button connected to digital input
input 2 must be activated prior to the pulse in
DI
• Connect multiple Start push-buttons in parallel.
• Stop is through a normally closed push-button connected to digital input
• Connect multiple Stop push-buttons in series.
• Parameter 1003 defines the direction. Selecting 1003 = 3 (
4 = 1 , 2 , 3 – Three-wire Start/Stop, Direction.
DI P P
• Start/Stop commands are through momentary push-buttons, as described for
• Direction control (requires parameter 1003 = 3 (
( 3 activated = Reverse; de-activated = Forward).
DI
5 = 1 , 2 , 3 – Start Forward, Start Reverse, and Stop.
DI P P P
• Start and Direction commands are given simultaneously with two separate momentary push-buttons (the
stands for "pulse").
• Start Forward command is through a normally open push-button connected to digital input
the drive, the digital input
• Start Reverse command is through a normally open push-button connected to digital input
the drive, the digital input
• Connect multiple Start push-buttons in parallel.
• Stop is through a normally closed push-button connected to digital input
• Connect multiple Stop push-buttons in series.
• Requires parameter 1003 = 3 (
6 = 6 – Two-wire Start/Stop.
DI
• Start/Stop is through digital input
• Parameter 1003 defines the direction. Selecting 1003 = 3 (
7 = 6, 5 – Two-wire Start/Stop/Direction.
DI
• Start/Stop is through digital input
• Direction control (requires parameter 1003 = 3 (
( 5 activated = Reverse; de-activated = Forward).
DI
8 = KEYPAD – Control Panel.
• Start/Stop and Direction commands are through the control panel when
• Direction control requires parameter 1003 = 3 (
9 = 1F, 2R – Start/Stop/Direction commands through
DI
• Start forward =
DI
• Start reverse =
DI
• Stop = both 1 and
DI
• Requires parameter 1003 = 3 (
10 = – Assigns the fieldbus Command Word as the source for the start/stop and direction commands.
COMM
• Bits 0,1, 2 of Command Word 1 (parameter 0301) activates the start/stop and direction commands.
• See Fieldbus user's manual for detailed instructions.
Start-Up
1) – the configuration of start, stop and direction commands.
EXT
1 ( 1 activated = Start;
DI DI
1 ( 1 activated = Start;
DI DI
3 must be activated prior to the pulse in
DI
3 must be activated during the pulse in
DI
).
REQUEST
6 ( 6 activated = Start;
DI DI
6 ( 6 activated = Start;
DI DI
1 activated and 2 de-activated.
DI
1 de-activated and 2 activated.
DI
2 activated, or both de-activated.
DI
).
REQUEST
1, and 2) for commands that enable start, stop
EXT EXT
1 de-activated = Stop).
DI
1 de-activated = Stop).
DI
stands for "pulse").
P
1. In order to start the drive, the digital
DI
1.
DI
DI
) is the same as 1003 = 1 (
REQUEST
)) is through digital input
REQUEST
1.
DI
2.
DI
DI
6 de-activated = Stop).
DI
) is the same as 1003 = 1 (
REQUEST
6 de-activated = Stop).
DI
)) is through digital input
REQUEST
EXT
).
REQUEST
1 and 2 combinations.
DI DI
2
DI
2.
).
FWD
1 , 2 .
DI P P
3
DI
1. In order to start
DI
2. In order to start
DI
3.
).
FWD
5.
DI
1 is active.
P