Function List - Mitsubishi Electric AE-200A Instruction Book

2-4. Function list

Electricity meter
measurement method
Apportionment method
Charge calculation method
*3*4
Standby electric energy
invoicing method
Printing/CSV output setting
*1 The AE-200 apportioned electricity billing function does not support the PLC (electric energy counting software) system.
*2 In systems where electric energy is entered manually (no-metering-device method), only charge rates will be calculated. Electric energy
charges cannot be calculated.
The "AE-200ChargeCalc.xlsm" tool, which supports easy calculation of air conditioning charges based on the calculated charge ratio, is
installed together with the Charge Calculation Tool. To use this tool, refer to "Appendix 1. Using the AE-200 Charge Calculation Support
Tool".
*3 Display and printing is possible for charge calculations up to 62 days previously.
*4 Charges for periods more than 62 days ago can be recalculated by periodically saving CSV files onto USB memory.
*5 Electricity meters are required for each AE-200 system (combination of AE-200 and AE-50/EW-50). (Electric energy will be apportioned
for each AE-200 system.)
*6 29th, 30th or 31st cannot be set as the closing date.
*7 The information displayed for printing and CSV output is different.
Refer to sections 3-5 "Printing the charge calculation results" and 3-6 "Examples of charge calculation results CSV output" for details.
WT07442X02
Systems where electric energy is metered (with-metering-device method):
*1*2 A system where the amount of electric energy and the charges are calculated by
connecting a PI controller and capturing electric energy pulses
Systems where electric energy is entered manually (no-metering-device method):
A system where the charge rates are calculated without connecting electricity meters
Outdoor unit electric energy apportionment
Operating electric energy (capacity save amount, thermo-ON time, fan operation time)
Standby electric energy (apportioned/not apportioned)
Indoor unit electric energy apportionment
Operating electric energy (apportioned/not apportioned)
Standby electric energy (apportioned/not apportioned)
Specified date calculation
The charge calculation results for a specified date can be output either as a CSV file or as
hard-copy printout.
Electric energy data from an AE-200 can be acquired either via a LAN connection or using
USB memory.
Closing date (automatic output) calculation
Daily or monthly charge calculation results can be automatically output either as a CSV
file or as hard-copy printout.
Electric energy data from an AE-200 can only be acquired via a LAN connection.
When outputting charge calculation results monthly, either the end of the month or any
date between the 1st and the 28th can be selected as the closing date.
When using closing date calculation, a PC with the Charge Calculation Tool installed must
be running at 5.00 AM on the day after the closing date for monthly calculation, or at 5.00
AM every day for daily calculation.
Either to invoice for standby electric energy (invoices to tenants) or to not invoice (left to the
*2 building owner's discretion) can be selected.
(Refer to section 6-7-1 "Billing function settings" for details.)
*7 Systems where electric energy is metered (with-metering-device method)
You can print and/or output CSV files for each energy management block (tenant).
• Apportioned electric energy (total)
• Apportioned electric energy and electricity charges for the respective unit prices (1-5)
• Air conditioning charges
You can print and/or output CSV files for each metering device.
• Measurement value (total)
• Unit (kWh, m3, MJ, (blank))
• Measurement values for the respective unit prices (1-5)
• Charges
Systems where electric energy is entered manually (no-metering-device method)
You can print and/or output CSV files for each energy management block (tenant).
• Indoor unit charge rate
• Outdoor unit charge rate
13
*5
*6