Metering Values (35 Registers Defined); Table 5-19. Tpu2000/Tpu2000R Metering Values - ABB TPU2000 Technical Manual

40176 Control Mask If Write Error
40177 Control Mask If Write Error
40178 Control Mask If Write Error
40179 Control Mask If Write Error

Metering Values (35 Registers Defined)

Metering Values are defined Table 5-19. Various data types are associated with each element. All metering
values are reported in primary units and should reflect the status as shown on the TPU2000/2000R Front Panel
Interface, ECP or WinECP metering screens. Many or the quantities are scaled, such as operating current to
denote a decimal point when read. Operate Current 40257 should be divided by 800 to obtain the decimal point
which is visible when viewing the value from the front panel.
Table 5-19. TPU2000/TPU2000R Metering Values Table
Register
Address
40257 Operate Current A
40258 Operate Current B
40259 Operate Current C
40260 Restraint Current A Winding 1
40261 Restraint Current B Winding 1
40262 Restraint Current C Winding 1
40263 Restraint Current A Winding 2
40264 Restraint Current-B Winding 2
40265 Restraint Current C Winding 2
40266 Restraint Current A Winding 3
40267 Restraint Current B Winding 3
40268 Restraint Current C Winding 3
40269 Restraint Angle-A Winding 1
40270 Restraint Angle-B Winding 1
40271 Restraint Angle-C Winding 1
40272 Restraint Angle-A Winding 2
40273 Restraint Angle-B Winding 2
40274 Restraint Angle-C Winding 2
40275 Restraint Angle-A Winding 3
40276 Restraint Angle-B Winding 3
40277 Restraint Angle-C Winding 3
40278 % Second Harmonic-A Winding 1
40278 % Second Harmonic-B Winding 1
40279 % Second Harmonic-C Winding 1
40279 % Fifth Harmonic-A Winding 1
TPU2000/2000R Modbus/Modbus Plus Automation Guide
6 = Invalid Data
7 = Settings being edited elsewhere in unit or remote edit disabled
8 = A write to one setting group attempted while actively editing
another.
9 = Breaker State Invalid
10 = Data entered is below minimum value
11 = Data entered is above maximum allowed
12 = Data entered is out of step
13 = Internal Software Error
32 = Reference Type or File Number Invalid
33 = Too many registers for Modbus Protocol
Unsigned Integer
Control Mask 1 Write Mask (MSW)
Unsigned Integer
Control Mask 1 Write Mask (LSW)
Unsigned Integer
Control Mask 2 Write Mask (MSW)
Unsigned Integer
Control Mask 2 Write Mask (LSW)
Item Scale Description
Factor
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
800 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
1 Unsigned 16 Bit
2 Unsigned High Order Byte LSB
2 Unsigned Low Order Byte MSB
2 Unsigned High Order Byte LSB
2 Unsigned Low Order Byte MSB
91