1MRS 750109-MUM Router Option Card for Lon® Star Coupler SROUT RER 111 Issued: 09.12.1997 Version: B2/24.2.2000 Checked: M.K. Technical Reference Manual Approved: T.S. We reserve the right to change data without prior notice. Contents: 1. Introduction ................4 2. Functions ...................7 2.1.
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Introduction ® The router option card is designed to be used within the LON Star Coupler RER 111. This device is not a "stand-alone" device. The router option card connects two different communication channels and forwards LonTalk™...
Page 5
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 MicroSCADA Fibre-optic connection Router Option Card Fibre-optic connection Fibre-optic connections SUBNET 1 to bay level devices Fibre-optic connections to bay level devices SUBNET 2 srout_2 )LJ 6\VWHP VWUXFWXUH ZKHQ WKH ILEUHRSWLF LQWHUIDFH LV XVHG WR GLYLGH D ODUJH...
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Functions The router option card has one 9-pin D-type connector for the twisted pair interface and one fibre-optic transceiver pair. There are two transceiver modules available for the twisted pair interface, either of which may be connected to the router core module RTR-10 via jumpers.
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 A message received from the twisted pair interface is passed on to the open-collector bus on the mother board, through the RTR-10 core module. A message received from the open collector bus is sent to the twisted pair interface through the RTR-10 core module.
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Mechanical and electrical design 3.1. Block diagram Net B Service Net A Twisted-pair Fibre-optic interface interface Configuration jumpers Continuous light control TP/XF 1250 Module Control TP/XF 78 Logic...
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Interfaces 4.1. General The router option card has five separate interfaces: - a 64-pin E1 card connector for the connection to the mother board of the RER 111 unit...
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 4.3. Fibre-optic interface For more information regarding fibre-optic cables and the fibre-optic connection of option cards, refer to the RER 111 manual 1MRS750104-MUM, chapter 6.2. 4.4. Service switch The service switch is used to produce a service-pin message.
FOC3 FOC3 FOC3 1MRS060023 1MRS060023 srout_8 SROUT Option Card )LJ ,QVWDOODWLRQ RI URXWHU RSWLRQ FDUG LQ WKH 5(5 XQLW 5.2. Configuration of router option card 5.2.1. Configuration instructions The router option card has 4 individual sets of jumpers. These are used to specify the transceiver type for router side A, the use of termination in the twisted pair network and the use of the fibre-optic transceiver pair.
Page 13
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 The figure below shows the required jumper settings of jumper groups S1, S2, S3 and S4 for each transceiver mode and the corresponding transceiver ID. Router side A can be set to be a TP/XF-78 interface, i.e. 78 kb/s speed, a TP/XF- 1250 interface, i.e.
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Once the router option card has been programmed, the fibre-optic mode can be configured for router side A, if required. To enable this, the communication parameters must be set from router side B. In the fibre-optic mode, the following...
Page 16
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 the same subnet, the message will not be passed on to subnet 2. But if node X in subnet 1 sends a message to node Z in subnet 2, the message will naturally be passed on to subnet 2).
Page 17
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 6LQJOHHQGHG comm_type: comm_pin_dir:'LUHFWPRGH ± VLQJOHHQGHG channel type: FXVWRP (behind the 6HOHFW &KDQQHO 7\SH button) comm_clock: (behind the %LW 5DWH button) (behind the %LW 5DWH button) input_clock: 3UHVV WKH 5RXWHU 2WKHU 6LGH EXWWRQ Remember, in this case the parameters mentioned above must be same on the both router sides.
Communication speed 1.25 Mb/s Connection to mother board 64-pin E1 connector Power source From the mother board +8 VDC Power consumption SROUT-C-MM option card <1.4 W SROUT-C-BB option card <1.4 W Size E1 card 100 mm x 160 mm Front plate 116.4 mm x 19.8 mm...
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Maintenance and service Self-diagnostics 7.1. 7.1.1. Fibre-optic receiver LED The receiver LED flashes when a message is being received from the fibre-optic channel. If the LED is continuously lit, the channel is heavily loaded or there is a malfunctioning device sending continuous light.
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Ordering information When ordering please state the following: 1. Quantity 2. Type of fibre-optic transceivers Type designation Router option card Type Designation Router option card with ST-type glass fibre-optic transceivers...
Router Option Card for Lon® Star Coupler SROUT 1MRS 750109-MUM RER 111 Appendix A Default values of communication parameters and routing tables for the router option card, sides A and B. These default values are set during manufacturing and they are stored in EEPROM memory of the Neuron chip.
Page 22
SROUT Router Option Card for Lon® Star Coupler 1MRS 750109-MUM RER 111 Table 3: Configuration structure fields and values programmed for router option card side B (open collector bus) during manufacturing Field of a structure Value Offset / # of bits Remarks...