Makita DLS110 Instruction Manual page 34

State of abnormality
7KH YDFXXP FOHDQHU GRHV QRW UXQ
along with the switch operation of
the tool.
7KH YDFXXP FOHDQHU UXQV ZKLOH WKH
tool's switch trigger is not pulled.
MAINTENANCE
WARNING:
Always be sure that the tool is
switched off and batteries are removed before
attempting to perform inspection or maintenance.
Failure to removing the batteries and switch off the
tool may result in accidental start up of the tool which
PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
WARNING:
Always be sure that the blade is
sharp and clean for the best and safest perfor-
mance. $WWHPSWLQJ D FXW ZLWK D GXOO DQG RU GLUW\ EODGH
may cause kickback and result in a serious personal
LQMXU\
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Adjusting the cutting angle
7KLV WRRO LV FDUHIXOO\ DGMXVWHG DQG DOLJQHG DW WKH IDFWRU\
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle
Lower the handle fully and lock it in the lowered position
by the stopper pin. Push the carriage toward the guide
fence. Loosen the grip and the screws which secure the
pointer and miter angle scale.
Fig.70: 1. Screw on pointer 2. Screws on miter
angle scale 3. Miter scale
Probable cause (malfunction)
7KH ZLUHOHVV XQLW LV QRW LQVWDOOHG LQWR
the tool.
7KH ZLUHOHVV XQLW LV LPSURSHUO\ LQVWDOOHG
into the tool.
7KH WHUPLQDO RI WKH ZLUHOHVV XQLW DQGRU
the slot is dirty.
7KH ZLUHOHVV DFWLYDWLRQ EXWWRQ RQ WKH
tool has not been pushed.
7KH VWDQGE\ VZLWFK RQ WKH YDFXXP
FOHDQHU LV QRW VHW WR $872 
More than 10 tools are registered to the
vacuum cleaner.
7KH YDFXXP FOHDQHU HUDVHG DOO WRRO
registrations.
No power supply
7KH WRRO DQG YDFXXP FOHDQHU LV DZD\
from each other (out of the transmission
range).
Radio disturbance by other appliances
which generate high-intensity radio
waves.
Other users are using the wireless
activation of the vacuum cleaner with
their tools.
34 ENGLISH
Remedy
Install the wireless unit correctly.
Gently wipe off dust and dirt on the terminal of the
wireless unit and clean the slot.
3XVK WKH ZLUHOHVV DFWLYDWLRQ EXWWRQ EULHÀ\ DQG PDNH
sure that the wireless activation lamp is blinking
in blue.
Set the stand-by switch on the vacuum cleaner to
$872 
Perform the tool registration again.
If more than 10 tools are registered to the vacuum
cleaner, the tool registered earliest will be cancelled
automatically.
Perform the tool registration again.
Supply the power to the tool and the vacuum
cleaner.
Get the tool and vacuum cleaner closer each other.
7KH PD[LPXP WUDQVPLVVLRQ GLVWDQFH LV DSSUR[L-
mately 10 m however it may vary according to the
circumstances.
Keep the tool and vacuum cleaner away from the
appliances such as Wi-Fi devices and microwave
ovens.
7XUQ RII WKH ZLUHOHVV DFWLYDWLRQ EXWWRQ RI WKH RWKHU
tools or cancel the tool registration of the other
tools.
Set the turn base to the 0° position using the positive
VWRS IXQFWLRQ 6TXDUH WKH VLGH RI WKH EODGH ZLWK WKH IDFH
RI WKH JXLGH IHQFH XVLQJ D WULDQJXODU UXOH RU WU\VTXDUH
:KLOH NHHSLQJ WKH VTXDUH WLJKWHQ WKH VFUHZV RQ WKH
PLWHU DQJOH VFDOH $IWHU WKDW DOLJQ WKH SRLQWHUV ERWK
right and left) with the 0° position in the miter angle
scale and then tighten the screw on the pointer.
Fig.71: 1. 7ULDQJXODU UXOH
Bevel angle
0° bevel angle
Push the carriage toward the guide fence and lock the
sliding movement by the stopper pin. Lower the handle
fully and lock it in the lowered position by the stopper
SLQ DQG WKHQ ORRVHQ WKH NQRE 7XUQ WKH ƒ DGMXVWLQJ
bolt two or three revolutions counterclockwise to tilt the
blade to the right.
Fig.72: 1. ƒ $GMXVWLQJ EROW 2. Screw
&DUHIXOO\ VTXDUH WKH VLGH RI WKH EODGH ZLWK WKH WRS
surface of the turn base using the triangular rule, try-
VTXDUH HWF E\ WXUQLQJ WKH ƒ DGMXVWLQJ EROW FORFNZLVH
7KHQ WLJKWHQ WKH NQRE ¿UPO\ WR VHFXUH WKH ƒ DQJOH \RX
have set.
Fig.73: 1. 7ULDQJXODU UXOH 2. Saw blade 3. 7RS VXU-
face of turn base
&KHFN LI WKH VLGH RI WKH EODGH VTXDUHV ZLWK WKH WXUQ EDVH
surface once again. Loosen the screw on the pointer.
$OLJQ WKH SRLQWHU ZLWK ƒ SRVLWLRQ LQ WKH EHYHO DQJOH
scale and then tighten the screw.