Table of Contents
Advertisement
• Start complete signal............................... 3-15
• Synchronization flag signal ..................... 3-15
Simultaneous start....................................... 10-12
Simultaneous starting axis start data No. (Axis 1
Cd.30
start data No.) (
Simultaneous starting axis start data No. (Axis 2
Cd.31
start data No.)(
Simultaneous starting axis start data No. (Axis 3
Cd.32
start data No.)(
Simultaneous starting axis start data No. (Axis 4
Cd.33
start data No.)(
Cd.37
Skip command (
Skip function ................................................ 12-66
Skip operation program................................. 6-47
Slight vibration suppression control selection
(
) ........................................................ 5-76
Pr.142
Slot................................................................... 2-6
Software stroke limit function...................... 12-29
Software stroke limit lower limit value (
....................................................................... 5-30
Software stroke limit selection (
Software stroke limit upper limit value (
....................................................................... 5-30
Software stroke limit valid/invalid setting
Pr.15
(
)....................................................... 5-30
S-pattern acceleration/deceleration processing
method......................................................... 12-87
S-pattern proportion (
Special start instruction (
Special start data instruction code setting value
Md.36
(
)...................................................... 5-138
Special start data instruction parameter setting
Md.37
value (
)............................................ 5-138
Special start repetition counter (
Specifications of input/output interfaces....... 3-18
Specifications of input/output signals ........... 3-14
Speed change 0 flag ................................... 5-134
Speed change function ............................... 12-42
Speed change program ................................ 6-43
Speed change request (
Speed control 10 x multiplier setting for degree
axis (
) ................................................ 5-44
Pr.83
Speed control 10 x multiplier setting for degree
axis function .............................................. 12-101
) ............................. 5-166
) .............................. 5-166
) .............................. 5-166
) .............................. 5-166
) ............................ 5-168
Pr.13
Pr.14
) ..... 5-30
Pr.12
Pr.35
)...................... 5-40
Da.13
) .............. 5-109
Md.41
)... 5-140
Cd.15
) ............... 5-156
Speed designation during OP shift (
........................................................................5-58
Speed differential compensation (
Speed integral compensation (
Speed limit function .....................................12-23
Speed limit value (
Speed loop gain (
Stop command processing for deceleration
stop selection (
Speed-position function selection (
Speed switching mode (
Speed-position switching control (ABS mode)
........................................................................9-91
Speed-position switching control (INC mode)
........................................................................9-86
Speed-position switching control movement
amount change register (
Speed-position switching control positioning
Md.29
)
amount (
Speed-position switching enable flag (
......................................................................5-164
)
Speed-position switching latch flag .............5-134
Speed-position switching signal ....................3-18
Spiral interpolation .........................................9-61
SSCNET
SSCNET
Standard speed switching mode ...................9-12
Start Hour (
Start complete signal .....................................3-15
Start data No. (
Start data pointer being executed (
......................................................................5-140
Start details setting program..........................6-53
Start history ..................................................5-120
Start history pointer (
Start information (
Start Minute: second (
Start No. (
Start positioning data No. setting value
Md.38
(
) ......................................................5-138
Start program .................................................6-55
Start program for high-level positioning control
......................................................................10-23
Md.31
Status (
Index - 8
Pr.128
Pr.8
).............................5-28
).............................5-70
Pr.127
Cd.42
)................................5-148
Pr.19
)..................5-34
Cd.23
).........................................5-132
.................................................... A-15
cable length..................................3-3
Md.5
) ......................................5-120
Da.12
) ..............................5-109
Md.8
) .......................5-122
Md.3
) ............................5-120
Md.6
) .....................5-120
Md.4
) ........................................5-120
)...........................................5-134
Pr.56
)
)...5-72
Pr.129
)........5-72
) ..5-34
Pr.81
) ..............5-162
Cd.24
)
Md.43
)
Advertisement
Table of Contents
