Table of Contents
Advertisement
[H]
Handling........................................................... 4-5
Hardware stroke limit function .................... 12-35
High-level positioning control........................ 10-2
[I]
In speed change processing flag (
..................................................................... 5-138
In speed control flag.................................... 5-134
In speed control flag (
Md.1
In test mode flag (
Inching movement amount (
Inching operation setting program ................ 6-41
Inching operation start time chart ............... 11-23
Inching operation timing and processing times
..................................................................... 11-19
Inching operation......................................... 11-17
Incremental system ....................................... 9-15
Independent positioning control...................... 9-6
Initialization program ..................................... 6-53
In-position range (
Pr.110
Input signal logic selection (
Interface internal circuit ................................. 3-21
Intentional stop .............................................. 6-69
Internal circuit ................................................ 3-19
Internal current consumption .......................... 3-3
Interpolation axis ........................................... 9-21
Interpolation control....................................... 9-21
Interpolation speed designation method (
....................................................................... 5-34
Interruption request during continuous operation
Cd.18
(
)...................................................... 5-158
[J]
JOG operation ............................................... 11-4
JOG operation acceleration time selection
Pr.32
(
)........................................................ 5-38
JOG operation deceleration time selection
Pr.33
(
)........................................................ 5-38
JOG operation setting program .................... 6-41
JOG operation start time chart.................... 11-11
JOG operation timing and processing times
....................................................................... 11-6
Cd.17
JOG speed (
JOG speed limit value (
JOG start signal............................................. 3-14
Md.40
)
Md.39
) ................... 5-138
) ........................... 5-118
Cd.16
)......... 5-158
) ........................... 5-64
Pr.22
) ........... 5-34
Pr.20
).................................. 5-158
Pr.31
) .................. 5-38
JUMP instruction..........................................9-112
[K]
[L]
Last executed positioning data No. (
......................................................................5-140
LED display functions ..................................15-60
LEND............................................................9-115
List of block start data..................................5-106
List of condition data....................................5-112
List of configuration devices ............................2-4
List of control data........................................5-148
List of dedicated instructions .........................14-2
List of devices used .........................................6-5
List of errors ...................................................15-6
List of functions ................................................3-4
List of input signal details...............................3-20
List of input/output signals .............................3-14
List of monitor data ......................................5-118
List of parameters ..........................................5-24
List of positioning data ...................................5-90
List of warnings ............................................15-50
LOOP ...........................................................9-114
Lower limit ......................................................3-21
Low-pass filter (
Low-pass filter selection (
[M]
M code (Condition data No., No. of LOOP to
)
LEND repetitions) (
M code OFF request....................................12-70
M code OFF request (
M code ON signal ..........................................3-15
M code ON signal output timing ..................12-69
M code ON signal output timing (
M code output function ................................12-69
Machine feed value........................................9-16
Machine feed value (
Machine OPR...................................................8-5
Machine response suppression filter 2
(
).........................................................5-72
Pr.133
Main functions ..................................................3-4
Major positioning controls................................9-2
Manual control ...............................................11-2
Manual pulse generator...................................2-4
Manual pulse generator................................ A-15
Manual pulse generator cable ..........Appendix-36
Index - 4
Md.46
)................................5-74
Pr.136
) ................5-76
Pr.141
Da.10
)........................5-102
Cd.7
) .....................5-150
Pr.18
Md.21
) .....................5-128
)
) ...5-32
Advertisement
Table of Contents
