Table of Contents
Advertisement
Axis operation status (
Axis stop signal ............................................. 3-17
Axis to be interpolated (
Axis warning detection flag ......................... 5-134
Md.15
Axis warning No. (
Axis warning occurrence (Hour) (
Axis warning occurrence (Minute: second)
Md.17
(
)...................................................... 5-126
[B]
Backlash compensation amount (
Backlash compensation function ................ 12-11
Basic parameters 1 ....................................... 5-24
Basic parameters 2 ....................................... 5-28
Block .............................................................. 10-2
Block No. being executed (
Block start (Normal start) .............................. 10-2
Block start data.............................................. 10-7
Block start data area (Nos. 7000 to 7004)...... 7-3
Buffer memory................................................. 7-2
Buffer memory area configuration .................. 7-5
BUSY signal .................................................. 3-14
[C]
Cable clamp................................................... 4-12
Combination of functions .............................. 3-12
Combination of main functions and sub
functions ........................................................ 3-12
Command in-position flag ........................... 5-134
Command in-position function .................... 12-83
Command in-position width (
Command speed (
Common functions ............................... 3-10, 13-4
Communicating signals between QD75MH and
each module .................................................. 1-19
Composite speed .......................................... 5-34
Condition data ............................................. 10-16
Condition operator....................................... 10-17
Condition operator (
Condition start ............................................. 10-10
Da.15
Condition target (
Conditional JUMP ....................................... 9-112
Configuration and roles of QD75MH memory
......................................................................... 7-2
Confirming the current value......................... 9-16
Confirming the installation and wiring........... 4-14
Md.26
) .................. 5-130
Da.5
).................... 5-92
Md.24
,
)........... 5-130
Md.16
). 5-126
Pr.11
Md.45
) .......... 5-140
Pr.16
).......... 5-32
Da.8
) .......................... 5-102
Da.16
) ...................... 5-115
) .......................... 5-115
Connection confirmation................................4-14
Connector.........................................................4-3
Continuous operation interrupt program .......6-48
Continuous path control...................................9-8
Continuous positioning control ........................9-7
Control data area .............................................7-3
Control functions ..............................................3-4
Control system (
Control system repetition counter (
......................................................................5-140
Count method 1) ..............................................8-9
). 5-30
Count method 2) ............................................8-11
Creep speed (
Current feed value .........................................9-16
Current feed value (
Current feed value during speed control (
........................................................................5-36
Current speed (
[D]
Data set method.............................................8-13
Data transmission process ..............................7-8
Deceleration stop ...........................................6-71
Deceleration curve.......................................12-98
Deceleration curve re-processing ...............12-98
Deceleration curve configuration.................12-99
Deceleration start flag (
Deceleration start flag function....................12-94
Deceleration start flag valid (
Deceleration time 0 (
Deceleration time 1 (
Deceleration time 2 (
Deceleration time 3 (
Deceleration time No. (
Detailed parameters 1 ...................................5-30
Detailed parameters 2 ...................................5-38
Details of input signals (QD75MH
........................................................................3-15
Details of output signals (PLC CPU
........................................................................3-17
Deviation counter clear ..................................3-19
Deviation counter value (
Disposal instructions......................................4-17
DOS/V personal computer ........................... A-15
Drive unit (Servo amplifier) ........................... A-15
Index - 2
Da.2
) ................................5-92
Md.42
Pr.47
)..................................5-54
Md.20
).......................5-128
Md.27
)..............................5-130
) ..................5-142
Md.48
)..........5-148
Cd.41
Pr.10
) .......................5-28
Pr.28
) .......................5-38
Pr.29
) .......................5-38
Pr.30
) .......................5-38
Da.4
) .....................5-92
PLC CPU)
)..............5-142
Md.102
)
Pr.21
)
QD75MH)
Advertisement
Table of Contents
