microHAM STATION MASTER Manual page 59

microHAM © 2016 All rights reserved
80 Meter CW:
The frequency range is defined as 3.500-3.680 MHz (based on the bandwidth of the dipole) and five antennas
are added: the vertical, CW dipole, transmit 4SQ with virtual rotator, receive 4SQ with virtual rotator, and a
special 80m group. The PA BCD code has been set to 2, remote PA and KEYOUT are enabled, the 80m BPF
output (B2) is selected and the sequencer output (preamplifier power) enabled.
80 Meter SSB:
The frequency range is defined as 3.680-4.000 MHz (to match the dipole with 75m matching network) and four
antennas have been added: Vertical, transmit 4SQ with virtual rotator, and receive 4SQ with virtual rotator. The
PA BCD code is again set to 2, remote PA and KEYOUT are enabled, the 80m BPF (B2) is selected, and the
sequencer output (preamplifier power) enabled.
60 Meters:
The frequency range is defined as 5.330-5.404 MHz and two antennas are selected: the vertical and receive
4SQ with virtual rotator. PA BCD code has been set for 0, remote PA and KEYOUT are DISABLED, the BPF
outputs are cleared to bypass the BPF, and NOT allowed on 60m, BPF outputs cleared to bypass BPF, and the
sequencer output (preamplifier power) enabled.
40 Meters (EU band):
The frequency range is defined as 7.000-7.100 MHz because of SWR on the inverted V and four antennas are
added: 3el Yagi, Vertical, receiving 4SQ with virtual rotator and Inverted V. The PA BCD code is set to 3,
Remote PA and KEYOUT are enabled, the 40m BPF (B3) is selected, and the sequencer output (preamplifier
power) enabled.
40 Meters (US band):
The frequency range is defined as 7.100-7.300 MHz and three antennas are added: 3el Yagi, Vertical, and
receiving 4SQ with virtual rotator. The PA BCD code is set to 3, Remote PA and KEYOUT are enabled, the 40m
BPF (B3) is selected, and the sequencer output (preamplifier power) enabled.
30 Meters:
The frequency range is defined as 10.100-10.150 MHz and one antenna is added: the vertical. The PA BCD
code is set to 4, Remote PA and KEYOUT are DISABLED, the BPF outputs are cleared to bypass BPF, and the
sequencer output is disabled (RX 4SQ preamplifier OFF all the time).
20 Meters:
The frequency range is defined as 14.000-14.350 MHz and two antennas are added: Vertical and SteppIR. The
PA BCD code is set to 5, Remote PA and KEYOUT are enabled, the 20m BPF (B4) is selected, and the
sequencer output is disabled (RX 4SQ preamplifier OFF all the time).
17 Meters:
The frequency range is defined as 18.060-18.170 MHz and two antennas are added: Vertical and SteppIR. The
PA BCD code is set to 6, Remote PA and KEYOUT are enabled, the BPF outputs are cleared to bypass the
BPF, and the sequencer output is disabled (RX 4SQ preamplifier OFF all the time).
15 Meters:
The frequency range is defined as 21.000-21.450 MHz and two antennas are added: Vertical and SteppIR. The
PA BCD code is set to 7, Remote PA and KEYOUT are enabled, the 15m BPF (B5) is selected, and the
sequencer output is disabled (RX 4SQ preamplifier OFF all the time).
59