Honeywell Voyager 1200g User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Barcode Reader
  5. VOYAGER 1200G
  6. User manual

Honeywell Voyager 1200g User Manual

Single-line laser bar code scanner
Hide thumbs Also See for Voyager 1200g:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Voyager™ 1200g/1202g
Single-Line Laser Bar Code Scanner
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for Honeywell Voyager 1200g

Summary of Contents for Honeywell Voyager 1200g

  • Page 1 Voyager™ 1200g/1202g Single-Line Laser Bar Code Scanner User’s Guide...
  • Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
  • Page 3 Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters. Cables greater than 3 meters may not meet class B performance. Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment.
  • Page 4 5627 BT Eindhoven The Netherlands Honeywell International Inc. shall not be liable for use of our product with equipment (i.e., power supplies, personal comput- ers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.

  • Page 5: Solids And Water Protection

    Caution - use of controls or adjustments or performance of procedures other than those specified herein may result in haz- ardous radiation exposure. Patents For patent information, please refer to www.honeywellaidc.com/patents. Solids and Water Protection The Voyager 1200g has a rating of IP42, immunity of foreign particles and dripping water.
  • Page 6 Hand Held Products Europe B.V. Nijverheidsweg 9-13 5627 BT Eindhoven The Netherlands Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
  • Page 7 Honeywell Scanning & Mobility Product Environmental Information Refer to www.honeywellaidc.com/environmental for the RoHS / REACH / WEEE information. Australia/NZ C-Tick Statement Conforms to AS/NZS 3548 EMC requirements. China SRRC Radio Certificate. CCC safety (CCB00-010BT base only) Japan Complies with Technical Regulations Conformity Certification of Specified Radio equipment.
  • Page 8 International LED Safety Statement LEDs have been tested and classified as “EXEMPT RISK GROUP” to the standard: IEC 62471:2006. Radio Technology Class II CB Scheme Certified to CB Scheme IEC 60950-1, Second Edition. Laser Safety Statement LASER LIGHT: DO NOT STARE INTO BEAM.
  • Page 9 Voyager 1200g Safety Label Locations Laser Output Internal Laser Cautions Compliance Markings information, Part Number, and Serial Number information Compliance Markings information...
  • Page 10 Voyager 1202g Safety Label Locations Laser Output Internal Laser Cautions Laser Safety Information Compliance Markings information, Part Number, and Serial Number information Compliance Markings information...
  • Page 11 CCB00-010BT Safety Label Locations Item Number, Compliance Serial Markings Number, and information Compliance Markings information...

  • Page 13: Table Of Contents

    ® Verifone Ruby Terminal Default Settings................2-7 ® Gilbarco Terminal Default Settings ..................2-7 Honeywell Bioptic Aux Port Configuration ................2-7 © Datalogic™ Magellan Bioptic Aux Port Configuration............2-8 NCR Bioptic Aux Port Configuration ..................2-8 Wincor Nixdorf Terminal Default Settings ................2-8 Wincor Nixdorf Beetle™ Terminal Default Settings .............2-9 Wincor Nixdorf RS232 Mode A ....................2-9...
  • Page 14 Keyboard Wedge Modifiers ....................2-18 ALT Mode ........................2-18 Keyboard Style ......................2-18 Keyboard Conversion ....................2-19 Keyboard Modifiers...................... 2-19 Inter-Scan Code Delay ....................2-20 <F0> Break Character ....................2-21 Keyboard Wedge Defaults................... 2-21 RS232 Modifiers ........................ 2-22 RS232 Baud Rate......................2-22 RS232 Word Length: Data Bits, Stop Bits, and Parity ..........
  • Page 15 Flash Updates ........................3-4 Beeper and LED Sequences and Meaning ................. 3-4 Scanner LED Sequences and Meaning................. 3-5 Base LED Sequences and Meaning................3-5 Base Power Communication Indicator................3-5 Reset Scanner........................3-6 Scanning While in Base Cradle ................... 3-6 Paging ..........................3-6 Paging Mode........................
  • Page 16 Good Read and Error Indicators..................4-1 Beeper – Good Read..................... 4-1 Beeper Volume – Good Read..................4-2 Beeper Pitch – Good Read.................... 4-2 Beeper - Transmit Order....................4-2 Beeper Pitch – Error ...................... 4-3 Beeper Duration – Good Read ..................4-3 Number of Beeps –...
  • Page 17 Prefix Selections........................5-2 Suffix Selections ........................5-3 Transmit Alternate Extended ASCII Characters ..............5-3 Function Code Transmit ...................... 5-4 Communication Check Character..................5-4 Intercharacter, Interfunction, and Intermessage Delays ............5-5 Intercharacter Delay ...................... 5-5 User Specified Intercharacter Delay ................5-5 Interfunction Delay......................
  • Page 18 Serial Trigger Commands....................10-3 Read Time-Out ......................10-3 Resetting the Standard Product Defaults ................10-3 Menu Commands ......................10-4 Chapter 11 - Product Specifications Voyager 1200g Product Specifications................11-1 Voyager 1202g Product Specifications................11-2 CCB00-010BT Product Specifications................11-3 CCB00-010BT Mounting ....................11-4...
  • Page 19 Standard Cable Pinouts..................... 11-5 Keyboard Wedge ......................11-5 Serial Output ....................... 11-5 RS485 Output ......................11-6 USB ..........................11-6 Chapter 12 - Maintenance Repairs ..........................12-1 Maintenance ........................12-1 Cleaning the Device..................... 12-1 Inspecting Cords and Connectors ................12-1 Replacing Cables in Corded Scanners................12-1 Replacing an Interface Cable in a Corded Scanner ............
  • Page 20 viii...

  • Page 21: Chapter 1 - Getting Started

    Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.

  • Page 22: Connecting With Keyboard Wedge

    2. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface. 3. The scanner beeps. 4. Verify the scanner or base operation by scanning a bar code from the Sample Symbols in the back of this manual.

  • Page 23: Connecting With Rs232 Serial Port

    5. Verify the scanner or base operation by scanning a bar code from the Sample Symbols in the back of this manual. The scanner beeps once. The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard. A carriage return (CR) suffix is added to bar code data.

  • Page 24: Connecting With Rs485

    Connecting with RS485 A scanner or base can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. Charge and Communications Base RS485 Connection: 2. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface.

  • Page 25: Reading Techniques

    Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Please contact the nearest techni-...

  • Page 26: Resetting The Custom Defaults

    Resetting the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings.

  • Page 27: Chapter 2 - Programming The Interface

    Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below.

  • Page 28: Opos Mode

    IBM Port 9B HHBCR-1 Interface IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each bar code above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 *...

  • Page 29: Usb Ibm Surepos

    OPOS Mode USB IBM SurePos Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface. Note: After scanning one of these codes, you must power cycle the cash register. USB IBM SurePos (USB Handheld Scanner) Interface...

  • Page 30: Usb Pc Or Macintosh Keyboard

    Scan one of the following codes to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically uses a class driver.

  • Page 31: Cts/Rts Emulation

    Scanning either of these codes also adds a CR and LF. USB Serial Emulation for Windows XP, Windows Server 2003, and later USB Serial Emulation for Windows 2000 Note: No extra configuration (e.g., baud rate) is necessary. CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On...

  • Page 32: Nak Retries

    Timeout Retries This setting limits the number of Communication Timeout retries. If the Timeout Retries is set to 0, the transmission is terminated after the initial Communication Timeout. Scan the bar code below, then set the number of retries (from 0- 255) by scanning digits from the Programming Chart, then scanning Save.

  • Page 33: Verifone ® Ruby Terminal Default Settings

    Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Character RTS/CTS with tim- eout and 232 ACK/NAK are also enabled.

  • Page 34: Datalogic™ Magellan © Bioptic Aux Port Configuration

    © Datalogic™ Magellan Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Datalogic Magellan bioptic scanner auxiliary port configura- tion. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Datalogic Magellan Bioptic Settings Note: If you are having unexpected results with this programming code, scan the Resetting the Custom Defaults...

  • Page 35: Wincor Nixdorf Beetle™ Terminal Default Settings

    Wincor Nixdorf Beetle™ Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. The following prefixes are programmed for each symbology: Symbology Prefix Symbology Prefix Code 128 EAN-13 Code 93 GS1-128 Codabar Interleaved 2 of 5...
  • Page 36 Keyboard Countries (Continued) Albania Arabic Azeri (Cyrillic) Azeri (Latin) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) 2 - 10...
  • Page 37 Keyboard Countries (Continued) Canada (French legacy) Canada (French) Canada (Multilingual) China Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) 2 - 11...
  • Page 38 Keyboard Countries (Continued) Estonia Faroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) 2 - 12...
  • Page 39 Keyboard Countries (Continued) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan ASCII 2 - 13...
  • Page 40 Keyboard Countries (Continued) Korea Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) 2 - 14...
  • Page 41 Keyboard Countries (Continued) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) 2 - 15...
  • Page 42 Keyboard Countries (Continued) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar 2 - 16...
  • Page 43 Keyboard Countries (Continued) Thailand Turkey F Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United Stated (Dvorak right) United States (International) Uzbek (Cyrillic) Vietnam 2 - 17...

  • Page 44: Keyboard Wedge Modifiers

    Keyboard Wedge Modifiers ALT Mode If your bar code contains special characters from the extended ASCII chart for example, an e with an accent grave (è), you will use ALT Mode. (See "Extended ASCII Characters" on page A-4.) Note: Scan the ALT mode bar code after scanning the appropriate Keyboard Country code. If your keystrokes require using the ALT key and 3 characters, scan the 3 Characters bar code.

  • Page 45: Keyboard Conversion

    Autocaps via NumLock bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key can- not be used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve the current state of the Caps Lock.

  • Page 46: Inter-Scan Code Delay

    Default = Control + ASCII Mode Off. Windows Mode Control + ASCII Mode On * Control + ASCII Mode Off DOS Mode Control + ASCII Mode Windows Mode Prefix/Suffix Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off. Numeric Keypad Mode On * Numeric Keypad Mode Off Inter-Scan Code Delay...

  • Page 47: F0> Break Character

    <F0> Break Character When your keyboard detects that any key is being pressed, released, or held down, the keyboard sends a packet of infor- mation known as a “scan code” to your computer. There are two different types of scan codes: “make codes” and “break codes.”...

  • Page 48: Rs232 Modifiers

    RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600. 1200 2400 4800 * 9600 19200 38400...

  • Page 49: Rs232 Word Length: Data Bits, Stop Bits, And Parity

    RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character.

  • Page 50: Rs232 Handshaking

    7 Data, 2 Stop, Parity Space 8 Data, 1 Stop, Parity Space 7 Data, 1 Stop, Parity Mark 7 Data, 2 Stop, Parity Mark 8 Data, 1 Stop Parity Mark RS232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. RTS/CTS Off: RTS/CTS is turned off so no data flow control is used, but RTS is still active.

  • Page 51: Rs232 Timeout

    Flow Control, No Timeout Character-Based Flow Control, No Timeout Two-Direction Flow Control Flow Control with Timeout Character-Based Flow Control with Timeout RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-5100 millisec- onds) by scanning digits from the Programming...

  • Page 52: Ack/Nak

    ACK/NAK After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again.

  • Page 53: Nak Retries

    NAK Retries This selection limits the number of NAK retries that can occur in ACK/NAK mode. Scan the bar code below, then set the number of retries (from 0-255) by scanning digits from the Programming Chart, then scanning Save. (5 is the recom- mended setting.) Default = 0, or disabled.

  • Page 54: Block Check Character

    Block Check Character When this selection is set to Transmit, the NCR Block Check Character (BCC) is expected with incoming messages and transmitted with outgoing messages. Default = Transmit. * Transmit Don’t Transmit NCR Prefix This selection allows you to program an NCR-specific prefix. Refer to the ASCII Conversion Chart (Code Page 1252), page A-2 to find the hex equivalent for the characters you want for the NCR prefix (typically, 02 for STX).

  • Page 55: Ncr Nof (Not-On-File) Error

    Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 Timeout must be set to 3000 in order to communicate with a bioptic scanner.

  • Page 56: Communication Timeout

    Communication Timeout This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response. Scan the bar code below, then set the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 2000 ms.

  • Page 57: Chapter 3 - Cordless System Operation

    Cordless System Operation Note: This chapter applies only to cordless scanning systems. It does not apply to corded scanners. How the Charge and Communications Base Works A cordless charge and communications base provides the link between the cordless scanner and the host system. The base contains an interface assembly and an RF communication module.

  • Page 58: Rf (Radio Frequency) Module Operation

    When data is scanned, the data is sent to the host system via the base. The cordless scanner recognizes data acknowledge- ment (ACK) from the base. If it cannot be determined that the data has been properly sent to the base, the scanner issues an error indication.

  • Page 59: Page Button

    (page 3-7) if you need to charge a scanner without linking it to the base. The model Voyager 1202g is designed for use with Honeywell battery pack model 100000495 (Li-ion 3.7Vdc, 7.4 watt hour), or model BAT-SCN01 (Li-ion 3.75Vdc, 9.0 watt hour).

  • Page 60: Battery Recommendations

    • Although your battery can be recharged many times, it will eventually be depleted. Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page 13-1 for additional information.

  • Page 61: Scanner Led Sequences And Meaning

    Scanner LED Sequences and Meaning Note: Pressing the button on the scanner causes the LED to glow red until it communicates successfully with the base. LED Indication Beeper Indication Cause Normal Operation Red Flash None Battery low Green Flash 1 beep Successful communication or linking Red, blinking Razz or error tone...

  • Page 62: Reset Scanner

    Reset Scanner Scanning this bar code reboots the scanner and causes it to relink with the base. Reset Scanner Scanning While in Base Cradle If you want to be able to scan bar codes while the scanner is in the base, scan the following Scanning in Cradle On bar code. If you want to only allow scanning when the scanner is out of the base, scan Scanning in Cradle Off.

  • Page 63: Paging Pitch

    Pitch Paging When you press the Page button on the base, the scanner associated with that base will begin beeping (see Page Button on page 3-3). You can set the pitch of the paging beep for the scanner by scanning one of the following bar codes. Default = Low.

  • Page 64: Linked Modes

    In order to program the base for Charge Only Mode, you must link a scanner to it. Once the scanner is linked to the base, scan the Charge Only Mode bar code. Any subsequent scanners placed in that base will charge without linking to it. The scanner used to program the base remains linked to the base.

  • Page 65: Unlinking The Scanner

    Unlinking the Scanner If a base has a scanner linked to it, that scanner must be unlinked before a new scanner can be linked. Once the previous scan- ner is unlinked, it will no longer communicate with the base. To unlink the scanner from a base, scan the following Unlink Scan- ner bar code.

  • Page 66: Rangegate

    When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner power time-out bar code to change the time-out duration (in seconds). If the scanner is not activated during the timer interval, the scanner goes into power down mode. Whenever the scanner is acti- vated, the timer is reset.

  • Page 67: Batch Mode Beep

    Default = Batch Mode Off. * Batch Mode Off Automatic Batch Mode Inventory Batch Mode Batch Mode Beep When scanning in Batch Mode, the scanner beeps every time a bar code is scanned. When Batch Mode Beep is On, you will also hear a click when each bar code is sent to the host.
  • Page 68 Example: Add a quantity of 5 for the last item scanned. 1. Scan the item's bar code. 2. Scan the quantity 5 bar code. Example: Add a quantity of 1,500 for the last item scanned. 1. Scan the item's bar code. 2.

  • Page 69: Delete Last Code

    Delete Last Code If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code. Delete Last Code Record Counter If you wish to add a record counter to each bar code scanned in Batch Mode, scan Record Counter On. Your batch output would add a sequential number before each bar code, for example: 00001,bar code 1 00002,bar code 2...

  • Page 70: Clear All Codes After Transmission

    Batch Mode LIFO Clear All Codes After Transmission If you want to clear the scanner’s buffer of all data accumulated in Batch Mode after the data has been transmitted to the host system, scan Clear All Codes After Transmission. If you do not want the buffer cleared after transmission, scan Don’t Clear All Codes After Transmission.

  • Page 71: Transmit Records To Host

    Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-11), and your scanner is set to Don’t Transmit Records Automatically, you must scan the following bar code to transmit all stored records to the host system. Transmit Inventory Records Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the appli-...

  • Page 72: Using The Scanner With Bluetooth Devices

    0002 0003 0004 0005 0006 0007 Reset You may also scan the following Scanner Name bar code and scan up to 30 numbers and/or letters for the scanner name. For example, if you wanted to name the linked scanner “312,” you would scan the following bar code, scan the 3, 1, and 2 bar codes on the Programming Chart inside the back cover of this manual, then scan Save.

  • Page 73: Changing The Scanner's Bluetooth Pin Code

    To relink to the charge base, scan the Base BT Connection bar code. Non-Base BT Connection Base BT Connection Changing the Scanner’s Bluetooth PIN Code Some devices require a PIN code as part of the Bluetooth security features. Your scanner’s default PIN is 0000, which you may need to enter the first time you connect to your non-base Bluetooth device.

  • Page 74: Maximum Link Attempts

    Event Auto Reconnect On Auto Reconnect Off Base reset (firmware upgrade or Scanner behaves as if out of range. No attempt to relink made while base power cycle) is powered off. Button must be pressed to initiate relinking. Scanner reset due to firmware Relink occurs automatically.

  • Page 75: Reset Scanner And Base

    When the scanner goes out of range, 15 attempts are made to link to the base unit. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base, but retains any bar codes that may have been saved in batch mode.
  • Page 76 3 - 20...

  • Page 77: Chapter 4 - Input/Output Settings

    Input/Output Settings Power Up Beeper The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Power Up Beeper Off - Scanner * Power Up Beeper On - Scanner...

  • Page 78: Beeper Volume - Good Read

    Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High. Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (2350 Hz) High (4200 Hz)

  • Page 79: Beeper Pitch - Error

    Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz. * Razz (100 Hz) Medium (2000 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read.

  • Page 80: Led Indicators

    To change the number of error beeps, scan the following bar code and then scan a digit (1-9) bar code and the Save code on the Programming Chart inside the back cover of this manual. Default = 1. Number of Error Beeps/LED Flashes LED Indicators The green and red LEDs can be programmed to be On or Off and at different brightness levels to indicate various scanner states.

  • Page 81: Led Brightness

    Green LED On when CodeGate Disabled Red LED On when In-Stand Green LED On when In-Stand Red LED On with CTS Green LED On with CTS Red LED On when Battery is Low Green LED On when Battery is Low LED Brightness Default = Red High, Green High.

  • Page 82: In-Stand And Out-Of-Stand Settings

    Red Medium Green Medium * Red High * Green High In-Stand and Out-Of-Stand Settings The following settings program the scanner’s behavior when it is either in the stand, or out of the stand (hand-held). Caution: When working with In-Stand and Out-of-Stand settings, enable the settings you want before disabling those you do not want to use.

  • Page 83: Manual Activation Mode

    Presentation Mode with CodeGate Out-of-Stand: When the scanner is not in the stand, it automatically detects bar codes and decodes them. However, the data is not transmitted until you press the button. The laser remains on briefly after the transmission. (If you are accustomed to a Voyager 9540, this setting is the same as the 9540’s default.) Presentation Mode Out-of-Stand Presentation Mode with...

  • Page 84: Manual Activation Laser Timeout - Button Settings

    * End Manual Activation After Good Read In-Stand Do Not End Manual Activation After Good Read Out-of-Stand * End Manual Activation After Good Read Out-of-Stand Manual Activation Laser Timeout - Button Settings You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when the button is held down, and after it is released.

  • Page 85: Codegate

    CodeGate When CodeGate is On, the button is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the button is pressed. When CodeGate is Off, bar code data is transmitted when it is decoded.

  • Page 86: End Object Detection After Good Read

    * Object Detection Mode On In-Stand * Object Detection Mode Off Out-of-Stand Object Detection Mode On Out-of-Stand End Object Detection After Good Read After a bar code is successfully detected and read from the scanner, the laser can be programmed either to remain on and scanning, or to turn off.

  • Page 87: Object Detection Laser Timeout

    Object Detection Laser Timeout You can set a timeout for the length of time the laser remains on and attempting to decode bar codes after an object is detected. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1- 65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.

  • Page 88: Activation Character

    Activation Character This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-2, find the hex value that represents the character you want to use to trigger scanning. Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that ASCII...

  • Page 89: Deactivation Character

    Deactivation Character This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-2, find the hex value that represents the character you want to use to terminate scanning. Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that...

  • Page 90: Output Sequence Overview

    Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default Sequence symbol programs the scanner to the following Universal values.
  • Page 91 SEQBLKsequence editor start command code identifier for Code 39 9999 code length that must match for Code 39, 9999 = all lengths start character match for Code 39, 41h = “A” termination string for first code code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths start character match for Code 128, 42h = “B”...

  • Page 92: Output Sequence Editor

    Output Sequence Editor Enter Sequence Default Sequence Sequence Timeout You may wish to set the maximum time between bar code scans in an output sequence. If that maximum time is not met, the output sequence operation is terminated. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning...

  • Page 93: Require Output Sequence

    * Discard Partial Sequence Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. When it’s On/Not Required, the scanner will attempt to get the output data to conform to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is.
  • Page 94 4 - 18...

  • Page 95: Chapter 5 - Data Editing

    Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.

  • Page 96: To Clear One Or All Prefixes Or Suffixes

    Example: Add a Suffix to a specific symbology To send a CR (carriage return)Suffix for U.P.C. only: Step 1. Scan Add Suffix. Step 2. Determine the 2 digit hex value from the Symbology Chart (included in the Symbology Charts, beginning on page A-1) for U.P.C.

  • Page 97: Suffix Selections

    Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Transmit Alternate Extended ASCII Characters You may need to emulate special keyboard functions, such as up or down arrows, Alt/Make or Alt/Break commands, that are not supported in the Extended ASCII Character table. Refer to Alternate Extended ASCII Characters (page 5-3) for a range of key- board function keys and corresponding decimal and hex characters.

  • Page 98: Function Code Transmit

    Alternate Extended ASCII Characters (Continued) DEC HEX Keyboard Function DEC HEX Keyboard Function 135 87 159 9F Caps Lock 136 88 Page Up 160 A0 Num Lock 137 89 Page Down 161 A1 Left Alt 138 8A Right ALT 162 A2 Left Ctrl 139 8B Right CTRL...

  • Page 99: Intercharacter, Interfunction, And Intermessage Delays

    LRC Starts on 2nd Character Intercharacter, Interfunction, and Intermessage Delays Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage delays slow the transmission of data, increasing data integrity. Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data.

  • Page 100: Interfunction Delay

    Interfunction Delay An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the following Interfunction Delay bar code, then scan the number of 5ms delays, and the Save bar code using the...

  • Page 101: Chapter 6 - Data Formatting

    Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.

  • Page 102: Other Programming Selections

    universal number, indicating all lengths.) Step 6. Editor Commands Refer to (page 6-3). Scan the symbols that represent the command you want to enter. 94 alphanumeric characters may be entered for each symbology data format. Step 7. Scan Save to save your data format, or Discard to exit without saving your changes. Enter Data Format Save Discard...

  • Page 103: Terminal Id Table

    Terminal ID Table Terminal Model(s) Terminal ID PC/AT and compatibles PS2 Keyboard USB SurePOS Handheld Scanner USB SurePOS Tabletop Scanner RS232 True RS485 Serial PC Keyboard Mac Keyboard Japanese Keyboard (PC) HID POS Data Format Editor Commands Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character.
  • Page 104 The data is output as: 1234567890AB <tab><tab> Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page A-1).

  • Page 105: Move Commands

    Insert bar code length B4 Insert the bar code’s length in the output message, without moving the cursor. The length is expressed as a numeric string and does not include leading zeros. B3 and B4 Example: Insert the symbology name and length Send the symbology name and length before the bar code data from the bar code above.

  • Page 106: Search Commands

    Move the cursor to the beginning F7 Move the cursor to the first character in the input message. Syntax = F7. FE and F7 Example: Manipulate bar codes that begin with a 1 Search for bar codes that begin with a 1. If a bar code matches, move the cursor back to the beginning of the data and send 6 characters followed by a carriage return.
  • Page 107 Search forward for a string B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B0nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B0000454657374 will search forward for the first occurrence of the 4 character string “Test.”...

  • Page 108: Miscellaneous Commands

    Search backward for a non-matching character E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII code.
  • Page 109 0D is the hex value for a CR The data is output as: 1234 5678 <CR> Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position.

  • Page 110: Data Formatter

    If this bar code is read, the next data format, if there is one, will be used on this data. If there is no other format, the format fails and the raw data is output as 1234AB. If this bar code is read: the data is output as: AB1234 <CR>...

  • Page 111: Data Format Non-Match Error Tone

    Data Format Required, Keep Prefix/Suffix Data Format Required, Drop Prefix/Suffix Data Format Non-Match Error Tone When a bar code is encountered that doesn’t match your required data format, the scanner normally generates an error tone. However, you may want to continue scanning bar codes without hearing the error tone. If you scan the Data Format Non-Match Error Tone Off bar code, data that doesn’t conform to your data format is not transmitted, and no error tone will sound.

  • Page 112: Single Scan Data Format Change

    Single Scan Data Format Change You can also switch between data formats for a single scan. The next bar code is scanned using an alternate data format, then reverts to the format you have selected above (either Primary, 1, 2, or 3). For example, you may have set your device to the data format you saved as Data Format 3.

  • Page 113: All Symbologies

    Symbologies This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. • All Symbologies • GS1-128 • Airline Code 5 - see Straight 2 of 5 IATA (two-bar start/stop) • Interleaved 2 of 5 •...

  • Page 114: Codabar

    Codabar <Default All Codabar Settings> Codabar On/Off * On Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.”...

  • Page 115: Codabar Concatenation

    Validate Modulo 16 and Transmit Validate Modulo 7 CD, but Don’t Transmit Validate Modulo 7 CD and Transmit Validate CLSI, but Don’t Transmit Validate CLSI and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D”...

  • Page 116: Codabar Message Length

    Concatenation Timeout When searching for bar codes during concatenation, you may wish to set a delay used to find the next bar code. Set the length (in milliseconds) for this delay by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.

  • Page 117: Code 39

    Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character...

  • Page 118: Code 32 Pharmaceutical (Paraf)

    Code 39 Redundancy If you are encountering errors when reading Code 39 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 119: Full Ascii

    Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.

  • Page 120: Interleaved 2 Of 5

    Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On NULL Characters Interleaved 2 of 5 requires an even number of characters. When an odd number of characters is present, it is due to NULL characters embedded in the bar code.

  • Page 121: Nec 2 Of 5

    Validate and Transmit Interleaved 2 of 5 Redundancy If you are encountering errors when reading Interleaved 2 of 5 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.
  • Page 122 When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data.

  • Page 123: Code 93

    Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Code 93 Redundancy If you are encountering errors when reading Code 93 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 124: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)

    Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Redundancy If you are encountering errors when reading Straight 2 of 5 Industrial bar codes, you may want to adjust the redundancy count.

  • Page 125: Straight 2 Of 5 Iata (Two-Bar Start/Stop)

    Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.

  • Page 126: Matrix 2 Of 5

    Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Matrix 2 of 5 bar codes printed with a check character, but will not transmit the check character with the scanned data.

  • Page 127: Code 11

    Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 11...
  • Page 128 Check Digit Validation When Check Character is set to Validate and Transmit, the scanner will only read Code 11 bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data. Validate and Transmit One Check Digit Validate and Transmit Two...

  • Page 129: Code 128

    Code 128 <Default All Code 128 Settings> Code 128 On/Off * On 128 Group Separator Output If you wish to transmit embedded FNC1 characters as group separators (1B hex) with your Code 128 bar code output, scan the On bar code. When Off is scanned, nothing is transmitted for FNC1 characters. Default =Off. * Off Code 128 Redundancy If you are encountering errors when reading Code 128 bar codes, you may want to adjust the redundancy count.

  • Page 130: Code 128 Message Length

    Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood informa-...
  • Page 131 ISBT 128 Predefined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to select the pre-defined ISBT 128 Concatenation Sequence you wish to use. Once you have selected the concatenation sequence, use ISBT 128 Predefined Concatenation Sequences On/Off to enable this fea- ture.
  • Page 132 Default = Off. * Off Allow Predefined Sequence Require Predefined Sequence ISBT 128 User-Defined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to create a custom ISBT 128 Concatenation Sequence. Select the identifiers you want to transmit in the 1st and 2nd positions, both left and right.
  • Page 133 2nd Left Identifier 1st Right Identifier 2nd Right Identifier ISBT 128 User-Defined Concatenation Sequences On/Off The following selections allow you to enable or require the User-Defined ISBT 128 Concatenation Sequences. If you scan Off, the User-Defined concatenation sequences are disabled. If you scan the Allow User-Defined Sequence code, then the scanner will output only the data combination specified in the User-Defined concatenation sequence you created.
  • Page 134 Transmit Identifiers You may disable the transmission of the ISBT Code 128 data identifiers by scanning Off. When this selection is Off, the first 2 data (ID) characters are removed from the data stream unless the ISBT code contains the Donation Identification Number identifiers.

  • Page 135: Gs1-128

    GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Application Identifier Parsing This allows a single GS1-128 bar code to be broken into multiple transmissions based on the presence of application iden- tifiers (AI) embedded in the bar code. To use this feature, first enable 128 Group Separator Output (page 7-17).

  • Page 136: Telepen

    GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Telepen <Default All Telepen Settings>...

  • Page 137: Upc-A

    inside the back cover of this manual. Then scan the Save bar code. Default = 0. Telepen Redundancy Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional information.
  • Page 138 UPC-A Number System and Check Digit UPC-A sample showing the number system and check digit: Number Check Digit UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
  • Page 139 * 5 Digit Addenda Off UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 7-26. Default = Not Required. Required * Not Required Addenda Timeout...

  • Page 140: Upc-A/Ean-13 With Extended Coupon Code

    cover of this manual. Then scan the Save bar code. Default = 0. UPC-A Redundancy UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.

  • Page 141: Upc-A Number System 5 Addenda Required

    UPC-A Number System 5 Addenda Required This setting programs the scanner to require any combination of a coupon code, a 2 digit addenda, or a 5 digit addenda on UPC-A bar codes that begin with a “5.” The following settings can be programmed: Require Coupon Code/Addenda: All UPC-A bar codes that begin with a “5”...

  • Page 142: Upc-E0

    Addenda Timeout You can set a time during which the scanner looks for a coupon code. If a coupon code is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code UPC-A Number System 4 Addenda...
  • Page 143 UPC-E0 Number System The numeric system digit of a UPC-A symbol is normally transmitted at the beginning of scanned data. When using UPC- E Expand, the unit can be programmed so it will not transmit it. Default = On. * On UPC-E0 Number System and Check Digit UPC-E0 sample showing the number system and check digit: Number...
  • Page 144 UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda.

  • Page 145: Ean/Jan-13

    UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = Off. * Off UPC-E0 Redundancy If you are encountering errors when reading UPC-E0 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.
  • Page 146 * Do not Convert UPC-A EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
  • Page 147 * Not Required EAN-13 Beginning with 2 Addenda Required This setting programs the scanner to require a 2 digit addenda only on EAN-13 bar codes that begin with a “2.” The follow- ing settings can be programmed: Require 2 Digit Addenda: All EAN-13 bar codes that begin with a “2” must have a 2 digit addendum. The EAN-13 bar code with the 2 digit addendum is then transmitted as a single, concatenated bar code.
  • Page 148 EAN-13 Beginning with 378/379 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “378” or “379.” The following settings can be programmed: Require Addenda: All EAN-13 bar codes that begin with a “378”...
  • Page 149 Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “434” or “439.” The following settings can be programmed: Require Addenda: All EAN-13 bar codes that begin with a “434”...
  • Page 150 Default = Don’t Require 2 Digit Addenda. * Don’t Require 2 Digit Addenda Require 2 Digit Addenda EAN-13 Beginning with 978 Addenda Required These settings program the scanner to require a 5 digit addenda only on EAN-13 bar codes that begin with “978.” The fol- lowing settings can be programmed: Require 5 Digit Addenda: All EAN-13 bar codes that begin with “978”...

  • Page 151: Isbn Translate

    Require 5 Digit Addenda Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-13 Addenda Required.

  • Page 152: Issn Translate

    * Off Convert ISBN to 13-Digit When translating EAN-13 codes to the ISBN format, you can convert the bar code to a 13 digit format by scanning the Convert to 13-Digit On bar code below. Default = Convert to 13-Digit Off. Convert to 13-Digit On *Convert to 13-Digit Off ISBN Reformat...

  • Page 153: Ean/Jan-8

    ISSN Reformat When Reformat On is scanned, EAN-13 977 Bookland symbols are translated into their equivalent 8-digit ISSN num- ber format, with hyphens added to the output. For example, 9770123456787 will be transmitted as 0123-456-0. (You must first scan ISSN (page 7-40) before scanning Reformat On.) Default = Reformat Off.
  • Page 154 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda.

  • Page 155: Msi

    EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = Off. * Off EAN/JAN-8 Redundancy If you are encountering errors when reading EAN/JAN-8 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.
  • Page 156 When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data. * Validate Type 10, but Don’t Transmit Validate Type 10 and Transmit Validate 2 Type 10 Characters,...

  • Page 157: Msi Message Length

    MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Plessey Code <...

  • Page 158: Plessey Message Length

    Plessey Redundancy If you are encountering errors when reading Plessey bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 159: Gs1 Databar Limited

    = 0. GS1 DataBar Omnidirectional Redundancy GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On GS1 DataBar Limited Redundancy If you are encountering errors when reading GS1 DataBar Limited bar codes, you may want to adjust the redundancy count.

  • Page 160: Gs1 Databar Expanded

    GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Redundancy If you are encountering errors when reading GS1 DataBar Expanded bar codes, you may want to adjust the redundancy count.

  • Page 161: Gs1 Emulation

    * Off GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1 Composites.

  • Page 162: China Post (Hong Kong 2 Of 5)

    China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings> China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Redundancy If you are encountering errors when reading China Post (Hong Kong 2 of 5) bar codes, you may want to adjust the redundancy count.

  • Page 163: Keyboard Function Relationships

    Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-19 enable Control + ASCII mode. Function Code HEX/ASCII Value Full ASCII “CTRL”...

  • Page 164: Supported Interface Keys

    Country Codes United Kingdom ¢ Denmark Norway Spain Supported Interface Keys IBM AT/XT and PS/2 Apple Mac/iMac ASCII Compatibles, Supported Keys WYSE PC/AT Supported Keys Reserved Reserved Enter (KP) Enter/Numpad Enter Cap Lock CAPS ALT make ALT make ALT break ALT break CTRL make CNTRL make...

  • Page 165: Chapter 9 - Utilities

    Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.

  • Page 166: Installing Ezconfig-Scanning From The Web

    7. Using Explorer, go to the c:\windows\temp file. 8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program. 9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfig- Scanning.

  • Page 167: Resetting The Factory Defaults

    Resetting the Factory Defaults This selection erases all your settings and resets the scanner to the original factory defaults. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scan- ner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults.
  • Page 168 9 - 4...

  • Page 169: Chapter 10 - Serial Programming Commands

    Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming com- mand, refer to the corresponding programming bar code in this manual.

  • Page 170: Responses

    SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and SubTag fields.

  • Page 171: Serial Trigger Commands

    This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled; the Minimum Message Length (MIN) is set to 2 characters;...

  • Page 172: Menu Commands

    Menu Commands Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Product Default Settings Setting Custom Defaults Set Custom Defaults MNUCDF Save Custom Defaults DEFALT Resetting the Custom Defaults Activate Custom Defaults DEFALT Programming the Interface Plug and Play Codes Keyboard Wedge: PAP_AT...
  • Page 173 Page * Indicates default # Indicates a numeric entry Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Bioptic Aux Port PAPMAG NCR Bioptic Aux Port PAPNCR Wincor Nixdorf Terminal PAPWNX...
  • Page 174 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Greek (Latin) KBDCTY63 2-13 Greek (MS) KBDCTY66 2-13 Greek (Polytonic) KBDCTY60 2-13 Hebrew KBDCTY12 2-13 Hungarian (101 key) KBDCTY50 2-13 Hungary KBDCTY19 2-13 Iceland KBDCTY75 2-13 Ireland KBDCTY73 2-13 Italian (142)
  • Page 175 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Tatar KBDCTY85 2-16 Thailand KBDCTY94 2-17 Turkey F KBDCTY27 2-17 Turkey Q KBDCTY24 2-17 Ukrainian KBDCTY76 2-17 United Kingdom KBDCTY7 2-17 United Stated (Dvorak right) KBDCTY89 2-17 United States (Dvorak left) KBDCTY88 2-17...
  • Page 176 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry RS-232 Modifiers RS232 Baud Rate 300 BPS 232BAD0 2-22 600 BPS 232BAD1 2-22 1200 BPS 232BAD2 2-22 2400 BPS 232BAD3 2-22 4800 BPS 232BAD4 2-22 *9600 BPS 232BAD5 2-22 19200 BPS...
  • Page 177 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry RS232 Handshaking *RTS/CTS Off 232CTS0 2-24 Flow Control, No Timeout 232CTS1 2-25 Character-Based Flow Control, No 232CTS7 2-25 Timeout Two-Direction Flow Control 232CTS2 2-25 Flow Control with Timeout 232CTS3 2-25 Character-Based Flow Control with...
  • Page 178 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Scanning While in Base Cradle Scanning in Cradle Off BT_SIC0 *Scanning in Cradle On BT_SIC1 Paging Mode BEPPGE1 BEPPGE0 Paging Pitch Low (*1000) (min 100Hz) BEPPFQ1000 Medium (3250) BEPPFQ3250 High (4200) (min 5000Hz) BEPPFQ4200...
  • Page 179 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Record Counter *Record Counter Off BATENT0 3-13 Record Counter On BATENT1 3-13 Total Records Total Records BATNRC 3-13 Batch Mode Output Order *FIFO BATLIF0 3-13 LIFO BATLIF1 3-14 Clear All Codes After Transmission *Don’t Clear All Codes After Transmission...
  • Page 180 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Beeper - Transmit Order *Before Transmission BEPWHN1 After Transmission BEPWHN2 Beeper Pitch - Error (Frequency) *Razz (100 Hz) BEPFQ2100 Medium (2000 Hz) BEPFQ22000 High (4200 Hz) BEPFQ24200 Beeper Duration - Good Read *Normal Beep BEPBIP0...
  • Page 181 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry In-Stand and Out-of-Stand Settings In-Stand Defaults AISDFT Out-of-Stand Defaults AOSDFT Presentation Mode Out-of-Stand PAPPM1 Presentation Mode with CodeGate Out-of- PAPPM2 Stand Manual Activation Mode Off In-Stand AISMEN0 *Manual Activation Mode On In-Stand AISMEN1 Manual Activation Mode Off Out-of-Stand...
  • Page 182 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Object Detection Laser Timeout Out-of- AOSODT##### 4-11 Stand (Range 1 - 65525) *5000 ms *Object Detection Distance - Short In- AISRNG2 4-11 Stand Object Detection Distance - Long In-Stand AISRNG1 4-11 Object Detection Distance - Short Out-of-...
  • Page 183 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2 Transmit Alternate Extended ASCII *Transmit Alternate Extended ASCIi KBDEXT0 Characters Transmit Normal Extended ASCIi KBDEXT1 Function Code Transmit *Enable RMVFNC0...
  • Page 184 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Symbologies All Symbologies All Symbologies Off ALLENA0 All Symbologies On ALLENA1 Codabar Default All Codabar CBRDFT Settings CBRENA0 CBRENA1 Codabar Start/Stop Char. *Don’t Transmit CBRSSX0 Transmit CBRSSX1 Codabar Check Char.
  • Page 185 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Interleaved 2 of 5 Default All Interleaved I25DFT 2 of 5 Settings I25ENA0 I25ENA1 NULL Characters *Off I25NUL0 I25NUL1 Interleaved 2 of 5 Check Digit *No Check Char. I25CK20 Validate, But Don’t I25CK21...
  • Page 186 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Straight 2 of 5 IATA Message Length Minimum (1 - 80) *13 A25MIN## 7-13 Maximum (1 - 80) *15 A25MAX## 7-13 Matrix 2 of 5 Default All Matrix 2 of 5 X25DFT 7-14 Settings...
  • Page 187 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry ISBT128 Predefined Concatenation * Donation ID Number (001) ISBPCS0 7-19 Sequences and ABO/RhD Blood Groups (002) Donation ID Number (001) and ISBPCS1 7-19 Donor ID Number (019) Donation ID Number (001) and ISBPCS2 7-19...
  • Page 188 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Telepen Redundancy Range (0 - 10) *0 TELVOT## 7-25 Telepen Message Length Minimum (1 - 80) *3 TELMIN## 7-25 Maximum (1 - 80) *80 TELMAX## 7-25 UPC-A Default All UPADFT 7-25...
  • Page 189 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry UPC-E0 Number System UPEEXN1 7-31 UPEEXN0 7-31 UPC-E0 Check Digit *Off UPECKX0 7-31 UPECKX1 7-31 UPC-E0 Leading Zero *Off UPENSX0 7-31 UPENSX1 7-31 UPC-E0 Addenda 2 Digit Addenda On UPEAD21 7-32 *2 Digit Addenda Off...
  • Page 190 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry EAN-13 Beginning with 434/439 * Don’t Require Addenda ARQ4340 7-37 Addenda Required Require 2 Digit Addenda ARQ4341 7-37 Require 5 Digit Addenda ARQ4342 7-37 Require 2 or 5 Digit Addenda ARQ4343 7-37 EAN-13 Beginning with 977 Addenda...
  • Page 191 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry MSI Check Character *Validate Type 10, but Don’t Transmit MSICHK0 7-44 Validate Type 10 and MSICHK1 7-44 Transmit Validate 2 Type 10 Chars, but Don’t MSICHK2 7-44 Transmit Validate 2 Type 10 Chars and Transmit MSICHK3...
  • Page 192 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry GS1 Emulation GS1-128 Emulation EANEMU1 7-49 GS1 DataBar Emulation EANEMU2 7-49 GS1 Code Expansion Off EANEMU3 7-49 EAN8 to EAN13 Conversion EANEMU4 7-49 *GS1 Emulation Off EANEMU0 7-49 Postal Codes China Post (Hong Kong 2 of 5)

  • Page 193: Chapter 11 - Product Specifications

    Product Specifications Voyager 1200g Product Specifications Parameter Specification Mechanical Height 3.8 in. (97mm) Length 7.1 in. (180mm) Width 2.6 in. (66mm) Weight 4.41 oz. (125g) Electrical Input Voltage 5V + 5% Operating Power 700mW; 140 mA (typical) @ 5V Standby Power 350mW;...

  • Page 194: Voyager 1202G Product Specifications

    Parameter Specification Maximum Power Output < 1 mw Embedded Laser Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Maximum Power Output 10 mw Voyager 1202g Product Specifications Parameter Specification Mechanical Height 3.6 in. (92mm) Length 7.1 in.

  • Page 195: Ccb00-010Bt Product Specifications

    Parameter Specification Scan Pattern Single scan line Scan Angle Horizontal: 30° Scan Speed 100 scan lines per second Print Contrast 10% minimum reflectance difference Decode Capabilities Reads standard 1D and GS1 DataBar symbologies DOF with 3.5 mil resolution at standard range Typical Performance 5 mil Code 39 27 - 151mm (1.1 - 5.9 in.)

  • Page 196: Ccb00-010Bt Mounting

    Temperature Ranges: Operating - Charging 41° F to +104° F (5° C to 40° C) Operating - Non-Charging 32° F to +122° F (0° C to 50° C) Storage* 23°F to +95°F (-5°C to 35°C) Humidity 0 to 95% relative humidity, non-condensing Environmental Operational after 30 drops from 3.28 feet Mechanical Drop...

  • Page 197: Standard Cable Pinouts

    Supply power input +5V power Keyboard data Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.

  • Page 198: Rs485 Output

    Data + Data - Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.

  • Page 199: Chapter 12 - Maintenance

    The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.

  • Page 200: Replacing An Interface Cable In A Corded Scanner

    Replacing an Interface Cable in a Corded Scanner 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the underside of the scanner’s handle. This is the cable release. 4.

  • Page 201: Troubleshooting A Voyager Scanner

    6. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Troubleshooting a Voyager Scanner The scanner automatically performs self-tests whenever you turn it on. If your scanner is not functioning properly, review the following Troubleshooting Guide to try to isolate the problem.

  • Page 202: Troubleshooting A Cordless System

    The scanner won’t read your bar code at all. 1. Scan the sample bar codes in the back of this manual. If the scanner reads the sample bar codes, check that your bar code is readable. Verify that your bar code symbology is enabled (see Chapter 2.
  • Page 203 Reprogram the base/Access Point with the correct Plug and Play bar code. See Programming the Interface beginning on page 2-1. • The bas or Access Pointe may not be programmed to output your bar code data properly. For example, you scan “12345” and the host displays “A12345B.”...
  • Page 204 12 - 6...

  • Page 205: Chapter 13 - Customer Support

    Limited Warranty Honeywell International Inc. (“HII”) warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
  • Page 206 HII extends these warranties only to the first end-users of the products. These warranties are non-transferable. The duration of the limited warranty for the Voyager 1200g scanner is five (5) years. The duration of the limited warranty for the Voyager 1202g scanner and CCB00-010BT Charge Base is three (3) years.

  • Page 207: Symbology Charts

    Refer to Data Editing beginning on page 5-1 and Data Formatting beginning on page 6-1 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...

  • Page 208: Postal Symbologies

    Honeywell Possible modifiers Symbology UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity Postal Symbologies Honeywell Possible modifiers Symbology...

  • Page 209: Lower Ascii Reference Table

    Non-printable ASCII control Keyboard Control + ASCII (CTRL+X) Mode characters Windows Mode Control + X Mode On (KBDCAS2) Char Control + X Mode Off (KBDCAS0) CTRL + X CTRL + X function NP Enter CTRL+ A Select all Caps Lock CTRL+ B Bold ALT Make...
  • Page 210 Printable Characters (Continued) Character Character Character < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ Ç 0x48 up arrow ↓ ü 0x50 down arrow → ‚ é 0x4B right arrow ← ƒ â 0x4D left arrow „...
  • Page 211 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code – û 0x41 — ù 0x42 ˜ ÿ 0x43 ™ Ö 0x44 š Ü 0x57 › ¢ 0x58 œ £ Numeric Keypad + 0x4E ¥ Numeric Keypad - 0x4A ₧...
  • Page 212 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code ╩ Ê ╦ Ë ╠ Ì ═ Í ╬ Î ╧ Ï ╨ Ð ╤ Ñ ╥ Ò ╙ Ó ╘ Ô ╒ Õ ╓ Ö ╫ × ╪...

  • Page 213: Iso 2022/Iso 646 Character Replacements

    (standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
  • Page 214 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ⎯ ¥ ⎯ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...

  • Page 215: Unicode Key Maps

    Unicode Key Maps 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
  • Page 216 A - 10...

  • Page 218: Sample Symbols

    Sample Symbols UPC-A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN-13 9 780330 290951 Code 39 BC321 Codabar A13579B Code 93 123456-9$ Straight 2 of 5 Industrial 123456...
  • Page 219 Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012...

  • Page 220: Programming Chart

    Programming Chart...

  • Page 221: Programming Chart

    Programming Chart Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
  • Page 222 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 VG1200-UG Rev E 9/13...

This manual is also suitable for:

Voyager 1202g

Table of Contents