Cisco ATA186-I2 Administrator's Manual page 186

Using System Diagnostics
Example—Cisco ATA Event Messages
<142>00:00:40 192.168.3.169 [09]:[0]OFFHOOK
<142>00:00:43 192.168.3.169 [09]:[0]ONHOOK
<142>00:01:35 192.168.3.169 [09]:[0]OFFHOOK
<142>00:01:50 192.168.3.169 [09]:[0]DTMF 2 , insum:830200
<142>00:01:50 192.168.3.169 [09]:[0]DTMF 2 , insum:854313
<142>00:01:50 192.168.3.169 [09]:[0]DTMF 1 , insum:868411
<142>00:01:50 192.168.3.169 [09]:[0]DTMF 2 , insum:861215
<142>00:01:50 192.168.3.169 [09]:[0]DTMF 0 , insum:858638
<142>00:01:51 192.168.3.169 [09]:[0]DTMF # , insum:845590
<142>00:01:51 192.168.3.169 [09]:[0]CLIP 22120
These messages include the following information:
Priority=142, which means that the facility value is 17 (local use 1) and the severity value is 6
•
(informational messages). You can derive this information from RFC-3164.
The time offset of the first message is 40 seconds.
•
The tag value is 09, which corresponds to Cisco ATA event messages. This is derived from
•
on page
The ch (active line of the Cisco ATA) is line 0, which is the Phone 1 port of the Cisco ATA.
•
The messages include DTMF debugging (showing the key and the insum number), on/off hook,
•
Caller ID (CLIP/CLIR) and the callee number.
Example—Fax Event Messages
<150>00:00:11 192.168.3.169 [10]:[1]MPT mode 0
<150>01:07:27 192.168.3.169 [10]:[1:0]Rx FAX
<150>01:07:27 192.168.3.169 [10]:[1]Tx MPT PT=100 NSE pkt c0000000
<150>01:07:27 192.168.3.169 [10]:[1]MPT mode 2
<150>01:07:27 192.168.3.169 [10]:[1]codec: 0 => 0
<150>01:07:27 192.168.3.169 [10]:[1]MPT mode 3
<150>01:07:27 192.168.3.169 [10]:[1]Rx MPT PT=100 NSE pkt c0000000
These messages include the following information:
• Priority=150, which means that the facility value is 18 (local use 2) and the severity value is 6
(informational messages). You can derive this information from RFC-3164.
• The time offset of the first message is 11 seconds.
• The tag value is 10, which corresponds to Cisco ATA event messages. This is derived from
on page
The ch (active line of the Cisco ATA) is line 1, which is the Phone 2 port of the Cisco ATA..
•
• The messages include fax detection, transmit/receive NSE packet status and Fax codec switch
information.
Example—RTP Statistic Messages
<182>00:01:58 192.168.3.169 [16]:[0]RTP Tx dur:5, pkt:275, byte:44000
<182>00:01:58 192.168.3.169 [16]:[0]RTP Rx dur:7, pkt:226, byte:35921, latePkt:0 lostPkt:0
avgJitter:0
These messages include the following information:
Priority=182, which means that the facility value is 22 (local use 6) and the severity value is 6
•
(informational messages). You can derive this information from RFC-3164.
• The time offset of the first message is one minute and 58 seconds.
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for H.323 (version 3.0)
9-8
5-62.
5-62.
Chapter 9 Troubleshooting
Table 5-9
Table 5-9
OL-4804-01