GE DS-SD4-1 Reference Manual page 71

A
Active messaging (defined) 56
Alarms
alarm code definitions 41
major vs. minor 41
using STAT command to display 38
AMASK command 25
Antenna
installation 18
system gain, defined 56
Yagi, illustrated 11
Antennas 11
Applications 6
Multiple Address Systems (MAS) 6
point-to-multipoint system 6
point-to-point system 7
ASENSE command 25
B
BAUD command 26
Baud rate
setting for RJ-11 DIAG port (DLINK command) 28, 46
Bit, defined 56
Bits-per-second. See BPS 56
BPS (bits-per-second), defined 56
BUFF command 26
Byte, defined 56
C
Cable
maximum length, recommended 16, 17
Cable, loss due to length of coaxial at 960 MHz 12, 15
Cautions
use attenuation between all units in test setup 45
CKEY command 27
Command summary, table 21
Commands
AK (authorization key) 25
AMASK (set/display alarm triggers) 25
ASENSE (set alarm output state) 25
BAUD (set/display rate, encoding) 26
BUFF (set/display data handling mode) 26
CKEY (enable/disable continuous keying) 27
CTS (set/display CTS line response timer) 27
DATAKEY (enable/disable transmitter keying by radio) 28
descriptions 21–39
DEVICE (set/display radio behavior) 28
DKEY (deactivate transmitter after KEY command) 28
DLINK (enable/disable network-wide diagnostics) 28
DTYPE (set radio to root or node for diagnostics) 29
DUMP (display all programmed settings) 29
entering on Hand-Held Terminal (HHT) 21
INIT (reinitialize radio to factory defaults) 30
INIT xx10 (restore standard transceiver defaults) 30
INIT xx20 (configure radio for use with P-20 chassis) 30
KEY (activate transmitter) 31
MODEL (display radio model number code) 31
MODEM (set modem speed) 31
OWM (set/display owner's message) 33
OWN (set/display owner's name) 33
PTT (set/display key-up delay) 34
PWR (set/display RF forward output power) 34
RSSI (display RSSI) 34
RTU (enable/disable internal RTU) 35
RX (set/display receive frequency) 35
MDS 05-4670A01, Rev. E
RXTOT (set/display receive time-out timer value) 36, 39
SCD (set/display soft-carrier dekey delay) 36
SER (display radio serial number 36
SHOW (display DC voltage, data port, RF power) 36
SNR (display signal-to-noise ratio) 36
SREV (display software revision level) 37
STAT (display current alarm status) 38
SWC (switched carrier) 38
TEMP (display internal temperature) 38
TOT (set/display time-out value and timer status) 39
TX (set/display transmit frequency) 39
Conversions, dBm-Watts-Volts 55
CTS command 27
D
Data Circuit-terminating Equipment—See DCE 56
Data Communications Equipment—See DCE. 56
Data interface
display active connector port 36
Data Terminal Equipment—See DTE 56
DATAKEY command 28
dB. See Decibel 56
dBi, defined 56
dBm, defined 56
DCE (Data Circuit-terminating Equipment), defined 56
Decibel (dB), defined 56
Description, product 3, 4
DEVICE command 28
Diagnostics
interface specifications 44
network-wide, performing 44, 46
PC software used for 48
using InSite software for network-wide 45
Digital Signal Processing—See DSP. 56
DIN Rail Mounting Bracket 6
Display
alarm status (STAT command) 38
alarm triggers (AMASK command) 25
all programmed settings (DUMP command) 29
baud rate and encoding (BAUD command) 26
connector port, active (SHOW command) 36
CTS line response timer (CTS command) 27
data handling mode (BUFF command) 26
DC voltage (SHOW command) 36
key-up delay (PTT command) 34
model number code (MODEL command) 31
owner's message (OWM command) 33
owner's name (OWN command) 33
radio behavior (DEVICE command) 28
radio serial number (SER command) 36
receive frequency (RX command) 35
receive time-out timer value (RXTOT command) 36, 39
RF forward output power (PWR command) 34
RF output (SHOW command) 36
RSSI (RSSI command) 34
signal-to-noise ratio (SNR command) 36
soft-carrier dekey delay (SCD command) 36
software revision level (SREV command) 37
temperature, internal (TEMP command) 38
time-out value and timer status (TOT command) 39
transmit frequency (TX command) 39
DKEY command 28
DLINK command 28
use of 46
Downloading new software 48
DSP (Digital Signal Processing), defined 57
SD Series Reference Manual (x710 Mode) I-1