Docking The Hx3; Undocking The Hx3; Docked Hx3 Mode States; Ring Scanner Storage - Honeywell HX3 User Manual

Docking the HX3

1. Prepare the HX3 for docking by removing it from the armband, hip flip or voice case if used. Place the wearable acces-
sories in a clean, safe location.
2. Slide the HX3 armband brackets straight down into the side rails on either side of the docking bay, making sure the
cradle connector on the HX3 and the cradle connector in the docking bay line up.
3. Press the HX3 down firmly until both connectors "click" together.
4. When the HX3 is properly seated in the docking bay, tap the Power button on the HX3. The PWR LED on the cradle
illuminates if the HX3 is properly seated in the cradle. If the cradle PWR LED does not illuminate, remove the HX3 from
the bay and reinsert.
5. Place the tethered battery, if any, in a battery charging bay. Battery charging commences. The battery does not need
to be disconnected from the HX3, if desired.
6. Place the tethered Ring Scanner, if any, in the Ring Scanner bay. The Ring Scanner does not need to be disconnected
from the HX3.
7. The docked HX3 is ready to use AC power for communication and backup battery recharging.

Undocking the HX3

Important: Do not put pressure on the HX3 display when removing the HX3 from the cradle.
1. Hold the HX3 firmly, and brace your thumb on or under the logo (just above the HX3 display). Hint: Pushing down with
your fingertips in the fingertip depression (behind the HX3) at the same time may be helpful.
2. Pull the HX3 straight up to disconnect the cradle connector on the HX3 from the cradle connector in the docking bay.
3. If the ring scanner and battery were tethered to the HX3 while it was docked, they remain tethered when the HX3 is
removed from the cradle.
4. Reconnect the HX3 wearable device to the armband, voice case or hip flip, sliding the HX3 battery into the battery
sleeve.
Note: The <1mm hole in the Tethered Ring Scanner storage bay is used to guide the fastener (screw) when attaching the
desktop cradle to a flat, stable surface (fasteners, screwdrivers, etc., not supplied by Honeywell).

Docked HX3 Mode States

When the HX3 is not docked in a powered cradle it can be set to enter Suspend Mode using Start > Settings > Control Panel
> Power > Schemes tab.
When the HX3 is docked in a powered cradle it can be placed in Suspend Mode by tapping the Power key.
Switch State to Suspend Mode established in Start > Settings > Control Panel > Power > Schemes tab is not available until
the HX3 is disconnected from the cradle.
Pre-existing User Idle and System Idle function as scheduled when the HX3 is docked in a powered cradle.
IMPORTANT
• Do not put the HX3 into Suspend Mode (by tapping the Power key) while the HX3 is connected to peripheral devices (or
ActiveSync) through the connectors on the desktop cradle. The HX3 is unable to maintain the connection during Suspend
Mode.
• If the USB connections are interrupted due to a Suspend operation – when the HX3 resumes, disconnect the cables and then
reconnect the cables again to initiate USB and/or ActiveSync connection again.

Ring Scanner Storage

If Ring Scanning is required while the HX3 is receiving power through the desktop cradle, the AC Adapter should be assembled
and attached to the desktop cradle first.
The Ring Scanner can be placed in the depression between the battery charging bays while tethered to an HX3 in the Docking
bay.
The Ring Scanner depression can also be used to store an untethered ring scanner. The depression does not have a connec-
tor.
11 - 8