Huawei EchoLife HG8110 Service Manual page 219

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
If an ONT supports only four queues, the values of 4–7 of the priority-queue parameter in the gem add
command are invalid. After configuration recovers, Config state will be failed.
l If the ONT does not match, that is, Match state is mismatch, the port types and number of
ports undermatch the actual port types and number of ports supported by the ONT. In this
case, run the display ont capability command to query the actual capability of the ONT,
and then select one of the following modes to modify the ONT configuration:
– Create a proper ONT profile according to the actual capability of the ONT, and then run
– Modify the ONT profile according to the actual capability of the ONT and save the
Step 6 Specify the native VLAN for the ONT port.
ETH port 1 on the ONT is connected to the PC and the native VLAN is VLAN 10.
NOTE
The ont port native-vlan command is used for configuring the native VLAN of an ETH port. When a packet
is transmitted to the ONT, a VLAN tag is added to the packet; when a packet is transmitted out of the ONT, the
VLAN tag is removed from the packet. This command is applicable for only the L2 service (L2 Internet access
service) when the ONT functions as a bridge device. When the ONT functions as a gateway device, the
configuration of the port VLAN is implemented on the ONT Web page, NMS, or U2560 server.
huawei(config-if-gpon-0/1)#ont port native-vlan 1 1 eth 1 vlan 10
huawei(config-if-gpon-0/1)#ont port native-vlan 1 2 eth 1 vlan 10
Step 7 Configure traffic profiles.
You can run the display traffic table ip command to query the traffic profiles existing in the
system. If the traffic profiles existing in the system do not meet the requirements, you need to
run the traffic table ip command to add a traffic profile.
l HSI service: The profile ID is 8, the CIR is 4 Mbit/s, the priority is 1, and packets are
scheduled according to the priority carried.
l VoIP service: The profile ID is 9, no rate limitation in the upstream and downstream
directions, the priority is 6, and packets are scheduled according to the priority carried.
l Wi-Fi service: The profile ID is 10, the CIR is 6 Mbit/s, the priority is 1, and packets are
scheduled according to the priority carried.
l U2560 management channel: The profile ID is 11, no rate limitation in the upstream and
downstream directions, the priority is 7, and packets are scheduled according to the priority
carried.
huawei(config-if-gpon-0/1)#quit
huawei(config)#traffic table ip index 8 cir 4096 priority 1 priority-policy tag-In-
Package
huawei(config)#traffic table ip index 9 cir off priority 6 priority-policy tag-In-
Package
huawei(config)#traffic table ip index 10 cir 6144 priority 1 priority-policy tag-In-
Package
huawei(config)#traffic table ip index 11 cir off priority 7 priority-policy tag-In-
Package
Step 8 Create service ports.
l HSI service: Set the service port indexes to 1 and 2, SVLAN ID to 100, GEM port ID to 1,
and CVLAN ID to 10. Use traffic profile 8.
l VoIP service: Set the service port indexes to 3 and 4, SVLAN ID to 200, GEM port ID to 2,
and CVLAN ID to 20. Use traffic profile 9.
Issue 02 (2011-12-08)
NOTE
the ont modify command to modify the configuration data of the ONT.
modification. Then, the ONT automatically recovers the configuration successfully.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 Configuration
211