Huawei EchoLife HG8110 Service Manual page 218

EchoLife HG8010/HG8110/HG8240/HG8245/HG8247/
HG8447 GPON Terminal
Service Manual
3.
Step 5 Confirm that the ONT goes online normally.
After an ONT is added, run the display ont info command to query the current status of the
ONT. Ensure that Control flag of the ONT is active, Run State is online, Config state is
normal, and Match state is match.
huawei(config-if-gpon-0/1)#display ont info 1 1
---------------------------------------------------------------------
F/S/P
ONT-ID
Control flag
activated.
Run state
normally.
Config state
the
Match state
to
capability
...//The rest of the response information is omitted.
If the ONT state fails, the ONT fails to be in the up state, or the ONT does not match, check the
ONT state by referring to the above-mentioned descriptions.
l If Control flag is deactive, run the ont activate command in the GPON port mode to activate
the ONT.
l If the ONT fails to be in the up state, that is, Run state is offline, the physical line may be
broken or the optical transceiver may be damaged. You need to check both the material and
the line.
l If the ONT state fails, that is, Config state is failed, the ONT capability set outmatches the
actual ONT capabilities (For details about the ONT actual capabilities, see Reference of
GPON ONT Capability Sets). In this case, run the display ont failed-configuration
command in the diagnosis mode to check the failed configuration item and the failure cause.
Then, rectify the fault according to actual conditions.
Issue 02 (2011-12-08)
Number
F/S/P
Ont SN
Password
VenderID
Ont Version
Ont SoftwareVersion : V1R002C06
Ont EquipmentID
Ont autofind time
------------------------------------------------------------------------
huawei(config-if-gpon-0/1)#ont confirm 1 ontid 1 sn-auth 6877687714852900 omci
ont-lineprofile-id 10 ont-srvprofile-id 10
huawei(config-if-gpon-0/1)#ont confirm 1 ontid 2 sn-auth 6877687714852901 omci
ont-lineprofile-id 10 ont-srvprofile-id 10
NOTE
If multiple ONTs of the same type are connected to a port and the same line profile or service profile is
bound to the ONTs, you can add ONTs in batches by confirming the auto discovered ONTs in batches to
simplify the operation and increase the configuration efficiency. For example, the preceding command
can be modified as follows:
huawei(config-if-gpon-0/1)#ont confirm 1 all sn-auth omci ont-lineprofile-id
10 ont-srvprofile-id 10
(Optional) Bind an alarm profile to the ONT.
In this example, bind the default alarm profile, namely alarm profile 1 to the ONT.
huawei(config-if-gpon-0/1)#ont alarm-profile 1 1 profile-id 1
huawei(config-if-gpon-0/1)#ont alarm-profile 1 2 profile-id 1
: 0/1/1
: 1
: active
: online
: normal
: match
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
: 2
: 0/1/1
: 6877687714852901
:
: HWTC
: 120D0010
: 247
: 2010-12-10 14:59:12
//Indicates that the ONT is
//Indicates that the ONT goes online
//Indicates that the configuration status of
ONT is normal.
//Indicates that the capability profile bound
the ONT is consistent with the actual
of the ONT.
3 Configuration
210