Toro Groundsmaster 3200 Series Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Enclosure
  5. 3200
  6. Operator's manual
Toro Groundsmaster 3200 Series Operator's Manual

Toro Groundsmaster 3200 Series Operator's Manual

Winter enclosure
Hide thumbs Also See for Groundsmaster 3200 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Winter Enclosure
Groundsmaster
Model No. 31990—Serial No. 400000000 and Up
Safety
This product complies with all relevant European
directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.
Rollover Protection System
(ROPS) for a Cab
•
The ROPS is an integral part of the cab, which is
an effective safety device.
•
The ROPS consists of the roll bar, the seat, the
seat belt, the seat latch, and cab.
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
1. Cutting/dismemberment hazard; fan—stay away from
moving parts.
125-9688
1. Windshield wipers—off
2. Windshield wipers
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3200 or 3300 Series Traction Unit
93-7272
3. Windshield wipers—on
4. Spray windshield washer
fluid
Register at www.Toro.com.
•
Always wear the seat belt when you operate the
machine with a cab.
•
Ensure that the seat belt can be released quickly
in the event of an emergency.
•
Drive slowly and carefully.
•
Check carefully for overhead clearances (i.e.,
branches, doorways, electrical wires) before
driving under any objects and do not contact them.
•
Keep the cab in safe operating condition by
periodically thoroughly inspecting for damage and
keeping all mounting fasteners tight.
•
Replace a damaged cab. Do not repair or revise.
•
Do not remove or modify the ROPS.
decal93-7272
decal125-9688
Form No. 3458-441 Rev B
Operator's Manual
*3458-441*
Original Instructions (EN)
Printed in the USA
All Rights Reserved

Advertisement

Table of Contents
loading

Related Manuals for Toro Groundsmaster 3200 Series

Summary of Contents for Toro Groundsmaster 3200 Series

  • Page 1 125-9688 1. Windshield wipers—off 3. Windshield wipers—on 2. Windshield wipers 4. Spray windshield washer fluid *3458-441* © 2022—The Toro® Company Original Instructions (EN) Register at www.Toro.com. 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420 All Rights Reserved...
  • Page 2 decal140-6632 140-6632 1. Read the Operator’s 4. Fan and interior light (40 Manual for fuse information. 2. A/C clutch and condenser 5. Front of machine fan (25 A) 3. Windshield washer (20 A) decal130-5361 130-5361 1. Warning—read the Operator's Manual; operate the machine only from the driver's seat;...

  • Page 3: Table Of Contents

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Bolt (3/4 x 4 inches) Prepare the machine and cab. Nut (3/4 inch) Cab firewall Install the cab firewall. Left ROPS stop Right ROPS stop ROPS mount ROPS brace...

  • Page 4: Procedure Description Qty

    Procedure Description Qty. Hose Female coupler Female dust plug Straight fitting (3/8 NPT x 5/8 barb) Hose clamp Male coupler Male dust plug Install the hoses for the 37 hp engine. R-clamp Carriage bolt (1/4 x 3/4 inch) Flange nut (1/4 inch) Engine fitting Cable ties Straight adaptor (3/8 inch)

  • Page 5: Bolt (3/4 X 4 Inches)

    Preparing the Machine and Parts needed for this procedure: Bolt (3/4 x 4 inches) Nut (3/4 inch) Procedure g302033 Figure 2 Note: Save the shipping pallet for long term storage 1. Cotter pin 2. Pin after the cab is removed. Save all hardware for the machine when installing or removing the cab.
  • Page 6 g302034 Figure 4 1. Nut 3. Bolt 2. Mower-deck latch Remove the nuts and bolts from the right armrest g301597 and fold it to the center (Figure Figure 6 1. Bolt 3. R-clamp 2. Fuel-vent tube g301595 Figure 5 1. Bolt 2.

  • Page 7: Cab Firewall

    Installing the Cab Firewall Parts needed for this procedure: Cab firewall Procedure Caulk the existing firewall openings on both sides at the locations shown in Figure 7 with black RTV sealant. g301598 Figure 7 g336508 1. Caulk these areas on both sides. Figure 8 1.

  • Page 8: Cab

    Installing the Cab Parts needed for this procedure: Left ROPS stop Right ROPS stop ROPS mount ROPS brace Retainer cover Seal Screw (1/4 x 3/4) Bolt (3/8 x 1 inch) Locknut (3/8 inch) Foam seal g301513 Figure 9 Procedure 1. Cab firewall 3.
  • Page 9 1. Bolt 3. Cab roof 2. Washer Use a hoist to support the cab and connect the cab hoist to the 4 lift points on the cab (Figure 12). Note: A cab hoist is available through your authorized Toro distributor.
  • Page 10 Install the left cover and 1 retainer cover into the left seal and secure the covers with 4 screws (1/4 x 3/4 inches); refer to Figure Install the right cover and 1 retainer cover into the right seal and secure the covers with 4 screws (1/4 x 3/4 inches);...

  • Page 11: Nut (5/16 Inch)

    Installing the Vent Tubes Parts needed for this procedure: Bolt (5/16 x 1-1/2 inch) Nut (5/16 inch) Plate clamp Tube clamp Procedure Install the vent tubes to each side of the cab. Refer to Figure Secure each vent tube with a bolt (5/16 x 1-1/2 inch), a plate clamp, a tube clamp, and a nut (5/16 inch) (Figure...

  • Page 12: Step Mount

    Install the deck step to the step mount with a carriage bolt (5/16 x 1-1/4 inch) and a nut (5/16 inch). Refer to Figure Install the step to the side of the machine with Installing the Step 2 carriage bolts (3/8 x 7/8 inches), 2 nuts (3/8 inch), a carriage bolt (3/8 x 7/8 inch),and nut (3/8 inch).

  • Page 13: Hose

    Installing the Hoses for the 24 hp Engine Parts needed for this procedure: Hose Female coupler g302840 Figure 19 Female dust plug Straight fitting (3/8 NPT x 5/8 barb) 1. Floor mat Hose clamp Male coupler Male dust plug R-clamp Carriage bolt (1/4 x 3/4 inch) Flange nut (1/4 inch) Engine fitting...
  • Page 14 g301831 Figure 20 1. Male coupler 6. Nut (1/4 inch) 11. Carriage bolt (1/4 x 3/4 inch) 2. Straight fitting (3/8 NPT x 5/8 barb) 7. Hose 12. Female coupler 3. Hose clamp 8. Engine fitting 13. Female dust plug 4.
  • Page 15 g315428 Figure 21 1. Nut 4. Existing bracket 2. Bolt 5. Radiator valve 3. Right side g301828 Figure 22 Drain half of the engine coolant from the radiator 1. Direction of fluid flow 5. Nut (1/4 inch) by using the valve on the right side of the 2.
  • Page 16 Installing the Hoses for the 37 hp Engine Parts needed for this procedure: Hose Female coupler Female dust plug Straight fitting (3/8 NPT x 5/8 barb) Hose clamp g315428 Male coupler Figure 23 Male dust plug 1. Nut 4. Existing bracket R-clamp 2.
  • Page 17 g301830 Figure 24 1. Male coupler 6. Nut (1/4 inch) 11. Female coupler 2. Straight fitting (3/8 NPT x 5/8 barb) 7. Hose 12. Female dust plug 3. Hose clamp 8. Engine fitting 13. Hose 4. Dust cap 9. Direction of fluid flow 14.

  • Page 18: Washer-Fluid Bracket

    Installing the Washer-Fluid Tank Parts needed for this procedure: Washer-fluid bracket Washer-fluid tank Carriage bolt (5/16 x 3/4 inch) Locknut (5/16 inch) Procedure Install the tank to the bracket with 4 carriage bolts (5/16 x 3/4 inch) and 4 nuts (5/16 inch); refer to Figure g301829...

  • Page 19: Female-Hose Fitting

    Installing the Washer Fluid Hoses Parts needed for this procedure: Female-hose fitting Male-hose fitting Procedure Note: The hoses are extra long and need to be cut to install the connections. Route the hoses along the frame and back to the washer-fluid tank (Figure 28).

  • Page 20: Weight (6 Kg Or 15 Lb)

    Installing the Weights Parts needed for this procedure: Weight (6 kg or 15 lb) Bolt (3/8 x 3-1/2 inches) Washer (3/8 inch) Locknut (3/8 inch) Procedure Install 2 weights (6 kg or 15 lb) between the frame and the rear bumper with 2 bolts (3/8 x 3-1/2 inches), 2 washers (3/8 inch), and 2 locknuts (3/8 inch).

  • Page 21: No Parts Required

    Product Overview Controls Completing the Installation Cab Controls No Parts Required Procedure Check for leaks. Check for parts that interfere with moving parts and make corrections before operating the machine. Connect the negative (-) battery cable to the battery. Check the operation of all controls before operating the machine.
  • Page 22 Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Clean the cab air filters (replace them if they are torn or excessively dirty). After the first 250 hours Cleaning CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders.
  • Page 23 Disconnecting the Wire Storage Harness Remove the cab from the machine for storage. Disconnect the wire harness secured to the machine from the wire harness secured to the Preparing to Remove the cab at the relay location (Figure 29). Cab from the Machine Disconnect the connect attached to the main machine harness (Figure...
  • Page 24 Removing the Cab Remove the cab roof (Figure 11). Remove the ROPS stops and ROPS mounts (Figure 15). Note: Do not remove the firewall. Remove the covers and roll bar seals from the base of ROPS inside the cab (Figure 14).
  • Page 25 Notes:...
  • Page 26 Notes:...
  • Page 27 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
  • Page 28 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.

This manual is also suitable for:

Groundsmaster 3300 series31990

Table of Contents