Yamaha MO6 Owner's Manual page 206

Utility mode
[SF4] OTHER
AutoLoad
PowerOnMode
CtrlReset (Controller Reset)
[F2] OUTPUT
L&RGain
[F3] VOICE
These special voice-related settings are available only when entering the Utility mode from the Voice mode, letting you set parameters related to all the
Voices.
[SF1] MEQ (Master EQ)
[SF2] MEF (Master Effect)
[SF3] ARP CH
(Arpeggio Channel)
OutputSwitch
TransmitCh (Transmit channel)
[SF4] CTL ASN
(Controller Assign)
[F3] SEQ (Sequencer)
These special song- and pattern-related settings are available only when entering the Utility mode from the Song or Pattern mode.
[SF1] CLICK
Mode
Beat
Volume
Type
Owner's Manual
206
Determines whether the Auto Load function is on or off. When this is on, the instrument will automatically load
the specified files (from USB storage device) to User memory—whenever the power is turned on. For details
about the Auto Load function, see page 102.
Settings: on, off
This determines the default power-on mode (and memory bank)—letting you select which condition is
automatically called up when you turn the power on.
Settings: performance, voice (USR1), voice (PRE1), GM, last, master
performance ....Performance Play mode (User Performance 001)
voice (USR1)....Voice Play mode (User Voice "USR1: 001")
voice (PRE1) ....Voice Play mode (Preset Voice "PRE 1: 001")
GM ...................Voice Play mode (GM Voices "GM: 001")
last ...................The mode and program number registered the last time by the procedure on page 210.
master ..............Master Play mode (User Master 001)
Determines the status of the controllers (Modulation Wheel, Aftertouch, Foot Controller, Breath Controller,
Knobs, etc.) when switching between voices. When this is set to "hold," the controllers are kept at the current
setting. When this is set to "reset," the controllers are reset to the default states (below).
Settings: reset, hold
If you select "reset," the controllers will be reset to the following states/positions:
Pitch Bend .................... Center
Modulation Wheel ......... Minimum
Aftertouch .................... Minimum
Foot Controller ............. Maximum
Breath Controller .......... Maximum
Foot Switch .................. Off
Expression ................... Maximum
Foot Volume ................. Maximum
Sustain ......................... Off
Set the output gain of the L/MONO and R jacks.
Settings: 0dB, +6dB
[VOICE] [UTILITY] [F3]
From this display you can apply five-band equalization to all Voices, raising or lowering the level of each
frequency band (LOW, LOWMID, MID, HIGHMID, HIGH).
The parameters are the same as in the Performance Common Edit. See page 172.
Settings: For details about EQ, see page 141.
From this display you can set the Master Effect related parameters applied to all the Voices. The parameters
are the same as in the Performance Common Edit. See page 172.
From this display you can set parameters related to output of the Arpeggio MIDI data in the Voice mode.
This enables or disables MIDI data output for the Arpeggio function. When this is set to "on," Arpeggio data is
sent via MIDI—allowing you to send the Arpeggio data to an external sequencer or play back the Arpeggios on
connected MIDI tone generators.
Settings: on (enable), off (disable)
Determines the MIDI channel through which Arpeggio playback data will be sent (when Output Switch above is
on).
Settings: 1 – 16
Sets the parameters related to the controllers in the Voice mode. Details on each parameter are the same as in
Performance Common Edit. See page 173.
[SONG] or [PATTERN] [UTILITY]
From this display you can set the parameters related to the click sound (metronome) that is used during
recording or playback in the Song/Pattern mode.
Determines whether and when the metronome click will sound.
Settings: off, rec, rec/play, all
off .....................The click will not sound.
rec....................The click will sound during song/pattern recording only.
rec/play ............The click will sound during song/pattern recording and playback.
all .....................The click will always sound.
Determines on which beats the metronome click will sound.
Settings: 16 (16th notes), 08 (8th notes), 04 (quarter notes), 02 (half notes), 01 (whole notes)
Determines the click sound volume.
Settings: 0 – 127
Determines the click sound type.
Settings: 1 – 10
[F3]