Sony Betacam SX DNW-A100 Maintenance Manual page 104

3-1. Overview of Error Message
Error messages are described on Section 3-2 in the order of list.
Error List
Code Message
on time data display area
_ NO COMMUNICATION
_ WARM UP FAIL
01 REEL TROUBLE
02 REEL TROUBLE
03 REEL TROUBLE
04 REEL TROUBLE
05 REEL TROUBLE
06 TAPE TENSION
07 CAPSTAN TROUBLE
08 DRUM TROUBLE
09 TH/UNTH MOTOR
0A THREADING
10 HUMID
11 TAPE T/E SENSOR
12 TAPE TOP SENSOR
13 TAPE END SENSOR
14 FAN MOTOR
20 CASS COMP MOTOR
21 REEL SFT MOTOR
22 REEL POS SENSOR
23 THRED RING SENS
92 INTERNAL I/F 1
96 SY NV-RAM ERROR
97 SV NV-RAM
98 RF NV-RAM ERROR
99 INTERNAL I/F 2
D1 SSX CPU ERROR
D2 HDD INIT ERROR
D3 SSX DIAGNOSTIC
D4 SSX IC ERROR
D5 FILE SYSTEM
D6 SSX OP ERROR
D7 SCSI DRIVER
D8 SCSI TARGET
3-2
Page Description
3-4 Abnormality in the interface between the lower control panel (KY-364 board) and SYS1 CPU
(SS-63 board) is detected in the lower control panel side.
3-4 It is detected that the warm up of the hard disk drives failed. [This error message is displayed
when selecting the disk (DISK PROGRAM or DISK MASTER) as a device.]
3-5 Tape slacking is detected in the threading or unthreading operation.
3-6 Tape slacking or tape breaking is detected in the SEARCH, FF, or REW mode.
3-7 Tape slacking, tape breaking, or supply or take-up reel locking is detected in the REC or PLAY
mode.
3-8 An malfunctional tape transport speed is detected in the FF or REW mode.
3-8 The malfunctional operation of the supply or take-up reel is detected during cassette insertion.
3-9 Excessive tape tension is detected in the REC or PLAY mode.
3-9 Malfunction of capstan motor is detected.
3-10 Malfunction of drum motor is detected.
3-10 Malfunction of threading or unthreading operation is detected.
3-11 It is detected that the tape top processing is not completed in the threading mode.
3-11 Dew condensation is detected.
3-12 The tape top and tape end are detected simultaneously.
3-12 Malfunction of tape top sensor is detected.
3-13 Malfunction of tape end sensor is detected.
3-14 Malfunction of cooling fan motor is detected.
3-15 Malfunction of cassette compartment-up or down operation is detected.
3-15 Malfunction of movement of the reel table corresponding to the cassette size is detected.
3-16 The L-cassette and S-cassette positions of the reel table are detected simultaneously.
3-16 The thread end and unthread end states of the threading ring are detected simultaneously.
3-17 Abnormality in the interface between SYS1 CPU (on SS-63 board) and other CPU/MPU is
detected.
3-18 The abnormal operation of an NV-RAM (on SS-63 board) for the system control system is
detected.
3-19 The abnormal operation of an NV-RAM (on MS-50 board) for the servo system is detected.
3-19 The abnormal operation of an NV-RAM (on EQ-56, DM-89, or TBC-23 board) for the RF
system is detected.
3-20 Abnormality in the interface between SYS2 CPU (on SS-63 board) and SERVO CPU (on SS-
63 board) or MPU (on EQ-56, DM-89, TBC-23, or DIF-42 board) is detected.
3-21 Abnormality in CPU peripheral devices on SSX board is detected.
3-22 Abnormality is detected during the hard disk drive(s) initialization.
3-24 Abnormality is detected in the diagnostic process of the SSX board at turn on the power.
3-26 Abnormality is detected during the initialization or data transfer for SD-RAM on SSX board.
3-27 The occurrence of abnormal state related to the file system is detected during recording/
playing back the hard disk(s) or when to performing the recording/playing back the hard
disk(s).
3-28 Abnormality is detected during a record or a playback of the hard disk(s).
3-29 Abnormality in the SCSI bus is detected.
3-30 The occurrence of medium/hardware error in hard disk drive is detected.
DNW-A100/A50/A45
DNW-A100P/A50P/A45P