Canon Staple Finisher-D1 Service Manual page 7

0
Rear Alignment Motor (M109) -------------------------------------------------4-60
Removing the Front Alignment Motor (M108) -----------------------------4-61
Removing the Tray 1 Shift Motor (M105) -----------------------------------4-63
Removing the Tray 2 Shift Motor (M106) -----------------------------------4-64
Removing the Staple Shift Motor (M107) -----------------------------------4-65
Removing the Inlet Feed Motor (M200) -------------------------------------4-66
Removing the Processing Tray Paper Retainer Motor (M118) --------4-66
Removing the Buffer Feed Motor (M102) -----------------------------------4-67
Removing the Paper Trailing Edge Pushing Guide Motor (M113) ----4-67
Removing the Feed Motor (M101) --------------------------------------------4-68
Removing the Stack Delivery Upper Motor (M104) ----------------------4-69
Removing the Stack Delivery Lower/Shutter Motor (M122) ------------4-69
Removing the Swing Guide Motor (M110) ----------------------------------4-70
Other Parts ------------------------------------------------------------------- 4-71
Removing the Alignment Roller -----------------------------------------------4-71
Removing the Thrust Plate -----------------------------------------------------4-74
Removing the Folding Rollers (Upper)/(Lower) ---------------------------4-75
Switches ----------------------------------------------------------------------- 4-79
Removing the Staple Safety Switch (Front/Rear) (SW102/SW104) -4-79
PCBs --------------------------------------------------------------------------- 4-80
Removing the Finisher Controller PCB --------------------------------------4-80
Removing the Tray 1 Motor Driver PCB -------------------------------------4-81
Removing the Tray 2 Motor Driver PCB -------------------------------------4-82
Removing the AC Noise Filter PCB ------------------------------------------4-83
Removing the Power Supply Unit ---------------------------------------------4-83
Adjustment
Overview ------------------------------------------------------------------------5-2
Overview ----------------------------------------------------------------------------- 5-2
Detail Description ------------------------------------------------------------------ 5-2
Major Adjustments ----------------------------------------------------------------- 5-2
Basic Adjustment --------------------------------------------------------------5-3
Paper Bump Amount Adjustment at the high-accuracy punch mode - 5-3
Paper Return Roller Descension Timing Adjustment --------------------- 5-4
Stack Delivery Upper Roller Ascension Timing Adjustment ------------- 5-5
Paper Switchback Position Adjustment -------------------------------------- 5-6
0
Paper Return Roller Ascension (Angle) Amount Adjustment ----------- 5-7
Buffer Operation Enable/Disable Mode Setting ---------------------------- 5-8
Action on parts replacement -----------------------------------------------5-9
Checking the position attached the Swing Guide Unit-------------------- 5-9
Adjusting the position attached the Saddle Inlet Flapper Solenoid
(SL206) ------------------------------------------------------------------------------5-10
Note on replacing the finisher controller PCB -----------------------------5-10
Installation
How to Utilize This Installation Procedure ------------------------------6-2
Illustrations Used in This Procedure ------------------------------------------ 6-2
Descriptions Used in This Procedure ----------------------------------------- 6-2
When Using the Contained Parts (Bundled Components in the Shipping
Carton) -------------------------------------------------------------------------------- 6-2
Symbols in the Illustration ------------------------------------------------------- 6-2
Checking Before Installation -----------------------------------------------6-3
Checking the Power Supply ----------------------------------------------------- 6-3
Selecting the Site of Installation ------------------------------------------------ 6-4
Checking the Unpacking Space ------------------------------------------------ 6-5
Points to Note on Installation --------------------------------------------------- 6-6
Order of Installation of Options ---------------------------------------------------------- 6-6
Turning Off the Main Power of the Host Machine ---------------------------------- 6-7
Unpacking and Checking the Contents ----------------------------------6-8
Checking the Contents ----------------------------------------------------------- 6-8
Unpacking Procedure ------------------------------------------------------------- 6-9
Unpacking Procedure of the Saddle Unit [Booklet Finisher-D1 Only] -----
6-14
Installation Procedure ------------------------------------------------------ 6-16
Installing Options ------------------------------------------------------------------6-16
Preparation for Installation on Upstream Connection Machine Side
[Staple Finisher-D1 only] --------------------------------------------------------6-17
Connecting to Host Machine ------------------------------------------------------------6-17
Connecting to Document Insertion Unit ----------------------------------------------6-18
Connecting to Professional Puncher -------------------------------------------------6-18
Connecting to Paper Folding Unit -----------------------------------------------------6-19
Preparation for Installation on Upstream Connection Machine Side
0-7
0-7