Xconfiguration Video Output Connector [N] Resolution; Xconfiguration Video Presentation Defaultsource; Xconfiguration Video Selfview Default Mode; Xconfiguration Video Selfview Default Fullscreenmode - Cisco MX700 Reference Manual

Cisco TelePresence MX700 and MX800

Introduction

xConfiguration Video Output Connector [n] Resolution

This setting applies to Connector [2..3] for MX800 Single.
Define the resolution and refresh rate for the connected screen.
Requires user role: ADMIN, INTEGRATOR, USER
Default value: Auto
USAGE:
xConfiguration Video Output Connector
where
n
: Unique ID that identifies the video output connector. Range: 2..3 for single monitor
systems; 3..3 for dual monitor systems
Resolution
: Auto/1280_720_50/1280_720_60/1920_1080_50/1920_1080_60/1920_1200
_50/1920_1200_60
Auto: The system will automatically try to set the optimal resolution based on negotia-
tion with the connected monitor.
1280_720_50: The resolution is 1280 x 720, and the refresh rate is 50 Hz.
1280_720_60: The resolution is 1280 x 720, and the refresh rate is 60 Hz.
1920_1080_50: The resolution is 1920 x 1080, and the refresh rate is 50 Hz.
1920_1080_60: The resolution is 1920 x 1080, and the refresh rate is 60 Hz.
1920_1200_50: The resolution is 1920 x 1200, and the refresh rate is 50 Hz.
1920_1200_60: The resolution is 1920 x 1200, and the refresh rate is 60 Hz.

xConfiguration Video Presentation DefaultSource

Define which video input source to use as a default presentation source. This setting may be
used by the API and 3rd party user interfaces. It is not relevant when using the user interfaces
provided by Cisco.
Requires user role: ADMIN, USER
Default value: 3
USAGE:
xConfiguration Video Presentation DefaultSource:
where
DefaultSource
: 1/2/3/4
The video input source to use as default presentation source.
D15335.08 Cisco TelePresence MX700 and MX800 API Reference Guide CE9.2, NOVEMBER 2017.
About the API xConfiguration xConfiguration
n Resolution: Resolution
DefaultSource
xCommand

xConfiguration Video Selfview Default Mode

Define if the main video source (self-view) shall be displayed on screen after a call. The position
and size of the self-view window is determined by the Video Selfview Default PIPPosition and
the Video Selfview Default FullscreenMode settings respectively.
Requires user role: ADMIN, INTEGRATOR
Default value: Current
USAGE:
xConfiguration Video Selfview Default Mode:
where
Mode
: Off/Current/On
Off: self-view is switched off when leaving a call.
Current: self-view is left as is, i.e. if it was on during the call, it remains on after the call;
if it was off during the call, it remains off after the call.
On: self-view is switched on when leaving a call.

xConfiguration Video Selfview Default FullscreenMode

Define if the main video source (self-view) shall be shown in full screen or as a small picture-
in-picture (PiP) after a call. The setting only takes effect when self-view is switched on (see the
Video Selfview Default Mode setting).
Requires user role: ADMIN, INTEGRATOR
Default value: Current
USAGE:
xConfiguration Video Selfview Default FullscreenMode:
where
FullscreenMode
: Off/Current/On
Off: self-view will be shown as a PiP.
Current: The size of the self-view picture will be kept unchanged when leaving a call, i.e.
if it was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the
call, it remains fullscreen after the call.
On: The self-view picture will be shown in fullscreen.
105
API Reference Guide
xStatus Appendices
Mode
FullscreenMode
Copyright © 2017 Cisco Systems, Inc. All rights reserved.