Huawei USG6000 Upgrade Manual page 86

HUAWEI USG6000&USG9500
Upgrade Guide
Info: If want to reboot with saving diagnostic information, input 'N' and then e
xecute 'reboot save diagnostic-information'.
System will reboot! Continue?[Y/N]:y
Step 5 After FW_B is restarted, run the undo shutdown command to enable the heartbeat interface.
HRP_M<FW_B> system-view
HRP_M[FW_B] interface GigabitEthernet 1/0/7
HRP_M[FW_B-GigabitEthernet1/0/7] undo shutdown
HRP_M[FW_B-GigabitEthernet1/0/7] quit
Step 6 Wait for the session entries to be synchronized between the active and standby FWs. It takes
around two minutes to synchronize the entries. You can run the display firewall session table
command to check whether the numbers of sessions on the two FWs are consistent. If yes,
continue the following operations.
Step 7 Run the undo shutdown command to enable the service interface of FW_B.
HRP_S[FW_B] interface GigabitEthernet 1/0/3
HRP_S[FW_B-GigabitEthernet1/0/3] undo shutdown
HRP_S[FW_B-GigabitEthernet1/0/3] quit
HRP_S[FW_B] interface GigabitEthernet 1/0/1
HRP_S[FW_B-GigabitEthernet1/0/1] undo shutdown
HRP_S[FW_B-GigabitEthernet1/0/1] quit
HRP_S[FW_B] quit
HRP_S<FW_B> save
Info: The system is now comparing the configuration, please wait.
Warning: The configuration has been modified, and it will be saved to the next s
tartup saved-configuration file hda1:/vrpcfg.zip. Continue? [Y/N]:y
Now saving the current configuration to the slot 0....
Save the configuration successfully.
Step 8 Run the shutdown command to disable the service and heartbeat interfaces of FW_A (active
device). You must run the shutdown command to disable the service interface first and then
the heartbeat interface. You can run the shutdown command to disable the heartbeat interface
of FW_A but not that of FW_B.
HRP_M<FW_A> system-view
HRP_M[FW_A] interface GigabitEthernet 1/0/3
HRP_M[FW_A-GigabitEthernet1/0/3] shutdown
HRP_S[FW_A-GigabitEthernet1/0/3] quit
HRP_S[FW_A] interface GigabitEthernet 1/0/1
HRP_S[FW_A-GigabitEthernet1/0/1] shutdown
HRP_S[FW_A-GigabitEthernet1/0/1] quit
HRP_S[FW_A] interface GigabitEthernet 1/0/7
HRP_S[FW_A-GigabitEthernet1/0/7] shutdown
HRP_M[FW_A-GigabitEthernet1/0/7] quit
HRP_M[FW_A] quit
After the preceding operations, service traffic is switched to FW_B for forwarding.
Step 9 Set the system software for the next startup of FW_A.
HRP_M<FW_A> startup system-software xxxxx.bin
Info:System software for the next startup:hda1:/xxxxx.bin, start read file....
Succeeded in setting the software for booting system.
Step 10 Restart FW_A.
HRP_M<FW_A> reboot
Info: The system is now comparing the configuration, please wait.
Warning: The configuration has been modified, and it will be saved to the next s
tartup saved-configuration file hda1:/vrpcfg.zip. Continue? [Y/N]:y
Now saving the current configuration to the slot 0....
Save the configuration successfully.
Info: If want to reboot with saving diagnostic information, input 'N' and then e
xecute 'reboot save diagnostic-information'.
System will reboot! Continue?[Y/N]:y
Step 11 After FW_A is restarted, run the undo shutdown command to enable the heartbeat interface.
Issue 01 (2018-01-16) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1 USG6000
77