Mitsubishi Electric MDS-B-SPJ2 Series Specification Manual page 83

No. Abbr. Name
SP023 VGNI1 Speed loop gain
integral item during
speed control
SP024
SP025 GRA1 Spindle side No. of
gear teeth 1
SP026 GRA2 Spindle side No. of
gear teeth 2
SP027 GRA3 Spindle side No. of
gear teeth 3
SP028 GRA4 Spindle side No. of
gear teeth 4
SP029 GRB1 Motor shaft side
No. of gear teeth 1
SP030 GRB2 Motor shaft side
No. of gear teeth 2
SP031 GRB3 Motor shaft side
No. of gear teeth 3
SP032 GRB4 Motor shaft side
No. of gear teeth 4
< Class: Spindle/machine specifications >
No. Abbr. Name
SP033 SFNC1 Spindle function 1
SP034 SFNC2 Spindle function 2
SP035 SFNC3 Spindle function 3
SP036 SFNC4 Spindle function 4
SP037 SFNC5 Spindle function 5
SP038 SFNC6 Spindle function 6
SP039 ATYP Amplifier type
SP040 MTYP Motor type
SP041 PTYP Regenerative
resistor type
SP042 CRNG
SP043 TRNG
SP044 TRANS NC communication
cycle
6. Status Display and Parameter Setting
Description
The speed loop integral gain during speed
control is set. Normally, this is set so that the
percentage to SP022 (VGNP1) is approximately
constant.
Not used. Set to 0.
The No. of teeth on the spindle side is set for
gear 000.
The No. of teeth on the spindle side is set for
gear 001.
The No. of teeth on the spindle side is set for
gear 010.
The No. of teeth on the spindle side is set for
gear 011.
The No. of teeth on the motor shaft side is set
for gear 000.
The No. of teeth on the motor shaft side is set
for gear 001.
The No. of teeth on the motor shaft side is set
for gear 010.
The No. of teeth on the motor shaft side is set
for gear 011.
Description
This corresponds to bits, and sets the spindle
function 1 selection. Refer to section 6.2 (2) for
details.
This corresponds to bits, and sets the spindle
function 2 selection. Refer to section 6.2 (2) for
details.
This corresponds to bits, and sets the spindle
function 3 selection. Refer to section 6.2 (2) for
details.
This corresponds to bits, and sets the spindle
function 4 selection. Refer to section 6.2 (2) for
details.
This corresponds to bits, and sets the spindle
function 5 selection. Refer to section 6.2 (2) for
details.
This corresponds to bits, and sets the spindle
function 6 selection. Refer to section 6.2 (2) for
details.
The amplifier type is set.
Set a compliant motor No. from the standard
motors indicated in section 6.2.(3).
This is valid when SP034 (SFNC2) bit -0 is set
to 0. Set the applicable motor No. from the
standard shown in section 6.2(3).
The regenerative resistor type is set.
Set a compliant resistor No. from the
regenerative resistors indicated in section
6.2.(4).
Not used. Set to 0.
Not used. Set to 0.
The communication cycle with the NC is set.
6 − 3
Standard
TYP CNG Unit
setting
DEC 60 1/10
rad/s
DEC 0
DEC 1
DEC 1
DEC 1
DEC 1
DEC 1
DEC 1
DEC 1
DEC 1
Standard
TYP CNG Unit
setting
HEX 0000
HEX 0000
HEX 0000
HEX 0000
HEX 0000
HEX 0000
HEX 0000
HEX 0000
HEX 0000
DEC 0
DEC 0
DEC Standard = 0
Special = 1028
Tolerable
setting
range
0 ~ 1000
1 ~ 32767
1 ~ 32767
1 ~ 32767
1 ~ 32767
1 ~ 32767
1 ~ 32767
1 ~ 32767
1 ~ 32767
Tolerable
setting
range
0000 ~
FFFF
0000 ~
FFFF
0000 ~
FFFF
0000 ~
FFFF
0000 ~
FFFF
0000 ~
FFFF
0000 ~
FFFF
0000 ~
FFFF
0000 ~
FFFF
~
~
0 ~ 32727