Setpoint Settings - Send Current Setpoint; Setpoint Settings - Cyclic Sending Of The Current Set-Point Temperature (Min); Setpoint Adjustment; Setpoint Adjustment - Maximum Manual Increase During Heating Mode (0 - 15°C) - ABB -i-Bus-KNX Millenium Reference Manual

KNX Technical Reference Manual
®
ABB-i-Bus -KNX Millenium
Pos: 31.7.101 /DinA-4 -- Online/Applikations- / Parameterbeschreibungen -- (KNX)/Applikation/Objekt-RTR/Module/Sollwerteinstellungen — aktuellen Sollwert senden @ 40\mod_1421742735380_15.docx @ 313649 @ 3 @ 1
11.3.81

Setpoint settings - Send current setpoint

Options:
The current setpoint value can be sent to the bus either cyclically and after a change, or only
after a change.
Pos: 31.7.102 /DinA-4 -- Online/Applikations- / Parameterbeschreibungen -- (KNX)/Applikation/Objekt-RTR/Module/Sollwerteinstellungen — zyklisches Senden der aktuellen Solltemperatur (min) @ 40\mod_1421742783023_15.docx @ 313664 @ 3 @ 1
11.3.82

Setpoint settings - Cyclic sending of the current set-point temperature (min)

Options:
This parameter is used to specify the amount of time that will elapse before the current setpoint
value is automatically transmitted.
Note
This parameter is only available when the "Send current setpoint" is set on "Only
during change".
Pos: 31.7.103 /DinA-4 -- Online/Applikations- / Parameterbeschreibungen -- (KNX)/Applikation/Objekt-RTR/Module/Sollwertverstellung @ 40\mod_1421743359507_15.docx @ 313679 @ 3 @ 1
11.3.83

Setpoint adjustment

Note
This parameter is only available if the "Device function" parameter is set on either
"Single device" or "Master device".
Pos: 31.7.104 /DinA-4 -- Online/Applikations- / Parameterbeschreibungen -- (KNX)/Applikation/Objekt-RTR/Module/Sollwertverstellung — max. manuelle Anhebung beim Heizbetrieb (0 - 15°C) @ 40\mod_1421743407728_15.docx @ 313694 @ 3 @ 1
11.3.84 Setpoint adjustment — Maximum manual increase during heating mode (0 - 15°C)
Options:
This preset can be used to limit the manual increase during heating.
Note
This parameter is only available when the "Control function" parameter is set on
"Heating", "Heating with additional stage", "Heating and cooling" or "Heating and
cooling with additional stages".
Pos: 31.7.105 /DinA-4 -- Online/Applikations- / Parameterbeschreibungen -- (KNX)/Applikation/Objekt-RTR/Module/Sollwertverstellung — max. manuelle Absenkung beim Heizbetrieb (0 - 15°C) @ 40\mod_1421743479241_15.docx @ 313709 @ 3 @ 1
11.3.85 Setpoint adjustment — Maximum manual reduction during heating mode (0 - 15°C)
Options:
This preset can be used to limit the manual decrease during heating.
Note
This parameter is only available when the "Control function" parameter is set on
"Heating", "Heating with additional stage", "Heating and cooling" or "Heating and
cooling with additional stages".
KNX Technical Reference Manual | 1473-1-8681
Description of applications /
Cyclic and during change
Only for change
Setting option between 5 - 240
Setting option between 0 - 15
Setting option between 0 - 15
objects
— 58 —