Commissioning; Software; Preparatory Steps; Assigning A Physical Address - ABB -i-Bus-KNX Millenium Reference Manual

KNX Technical Reference Manual
®
ABB-i-Bus -KNX Millenium
Pos: 21.1 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Überschriften (--> Für alle Dokumente <--)/1. Ebene/G - L/Inbetriebnahme @ 11\mod_1279185496977_15.docx @ 83035 @ 1 @ 1
7

Commissioning

Pos: 21.2 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Überschriften (--> Für alle Dokumente <--)/2. Ebene/S - T/Software @ 30\mod_1348574361878_15.docx @ 239188 @ 2 @ 1
7.1

Software

Pos: 21.3 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Inbetriebnahme/KNX/KNX-Sensorik/Millenium/6122 - Busch-Wächter 180°/Inbetriebnahme - Software - Einleitung -- 6124 @ 40\mod_1421843093909_15.docx @ 314621 @ @ 1
Note
The devices are products of the KNX system and meet KNX guidelines. Detailed expert knowledge
by means of KNX training sessions for a better understanding is assumed.
To start the device a physical address must be assigned first. The physical address is assigned and the
parameters are set with the Engineering Tool Software ETS (from version ETS 3.0 f, or native application from
ETS 4).
Pos: 21.4 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Überschriften (--> Für alle Dokumente <--)/3. Ebene/U - Z/Vorbereitende Arbeitsschritte @ 31\mod_1351084403550_15.docx @ 243607 @ 3 @ 1
7.1.1

Preparatory steps

Pos: 21.5 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Inbetriebnahme/KNX/KNX-Sensorik/Millenium/6122 - Busch-Wächter 180°/Inbetriebnahme - Software - Vorber. Arbeitsschritte -- 6124 @ 40\mod_1421843968920_15.docx @ 314637 @ @ 1
1. Connect a PC via the KNX interface, e.g. the commissioning interface / adapter 6149/21-500, to the KNX bus
line. The Engineering Tool Software ETS (from version ETS 3.0 f, or native application from ETS 4) must be
installed on the PC.
2. Switch on the bus voltage.
Pos: 21.6 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Überschriften (--> Für alle Dokumente <--)/3. Ebene/P - R/Physikalische Adresse vergeben @ 31\mod_1351084813795_15.docx @ 243635 @ 3 @ 1
7.1.2

Assigning a physical address

Pos: 21.7 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Inbetriebnahme/KNX/KNX-Sensorik/Millenium/6124 - Raumtemperaturregler/Inbetriebnahme - Software - Phys. Adresse vergeben -- 6124 @ 41\mod_1421844197758_15.docx @ 314653 @ @ 1
1. Press the two top buttons (1) on the device
simultaneously.
The message "PROG" (2) appears in red on the display.
2. After the physical address has been programmed, the
message "PROG" goes out.
Pos: 21.8 /Layout bis 2014-11-11/Online-Dokumentation (+KNX)/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ @ 1
KNX Technical Reference Manual | 1473-1-8681
Commissioning
1 1
PROG
2
Fig. 8: Assigning a physical address
— 20 —