Table 2-22 Sfp Module Options; Table 2-23 Sfp Module Specifications - Cisco 12000 - Series Chassis Modular Expansion Base Hardware Installation Manual

Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters
The 10-Port Gigabit Ethernet SPA will only accept the SFP modules listed as supported in this document.
Note
An SFP module check is run every time an SFP is inserted into the 10-Port Gigabit Ethernet SPA and
only SFP modules that pass this check will be usable by the 10-Port Gigabit Ethernet SPA.
SFP modules exist for technologies other than Gigabit Ethernet and for products other than the 10-Port
Gigabit Ethernet SPA. However, the information in this document pertains only to SFP modules that plug
into the 10-Port Gigabit Ethernet SPA ports.
The SFP module has a receiver port (RX) and a transmitter port (TX) that compose one optical interface.
Table 2-22

Table 2-22 SFP Module Options

SFP Module
Product Number
SFP-GE-S
SFP-GE-L
SFP-GE-Z
SFP-GE-T

Table 2-23 SFP Module Specifications

Specification
Wavelength
Cabling distance (maximum)
Operating case temperature
range
Storage temperature range
Supply voltage range
Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007
and Table 2-23 provide SFP information and specifications.
SFP Module
Short wavelength
(1000BASE-SX)
Long wavelength/long haul
(1000BASE-LX/LH)
Extended wavelength
(1000BASE-ZX)
RJ-45 copper SFP module
(1000BASE-T)
Description
SFP-GE-S: 770 to 860 nm
SFP-GE-L: 1270 to 1355 nm
SFP-GE-Z: 1500 to 1580 nm
SFP-GE-T: N/A.
SFP-GE-S: 500 m on 50/125um MMF; 300 m on 62.5/125um MMF
SFP-GE-L: 6.2 miles (10 km)
SFP-GE-Z: 49.7 miles (80 km)
SFP-GE-T: 328 ft. (100 m)
SFP-GE-S: 23 to 185 degrees F (–5 to 85 degrees C)
SFP-GE-L: 23 to 185 degrees F (–5 to 85 degrees C)
SFP-GE-Z: 23 to 185 degrees F (–5 to 85 degrees C)
SFP-GE-S: –40 to 185 degrees F (–40 to 85 degrees C)
SFP-GE-L: –40 to 185 degrees F (–40 to 85 degrees C)
SFP-GE-Z: –40 to 185 degrees F (–40 to 85 degrees C)
SFP-GE-S: 3.1 to 3.5 V
SFP-GE-L: 3.1 to 3.5 V
SFP-GE-Z: 3.1 to 3.5 V
Cisco 12000 Series Router SIP and SPA Hardware Installation Guide
10-Port Gigabit Ethernet SPA Overview
Description
Contains a Class 1 laser of 850 nm for
1000BASE-SX (short-wavelength) applications.
Contains a Class 1 laser of 1310 nm for
1000BASE-LX/LH (long-wavelength)
applications.
Contains a Class 1 laser of 1550 nm for
1000BASE-ZX (extended-wavelength)
applications.
Provides full-duplex Gigabit Ethernet
connectivity to high-end workstations and
between wiring closets over an existing copper
network infrastructure.
2-25