Connecting To The Access Point Console Port - Cisco Aironet 1130AG Series Hardware Installation Manual

OL-8369-04 OL-8369-04

Connecting to the Access Point Console Port

Connecting to the Access Point Console Port
St Step ep 6 6
St Step ep 7 7
St Step ep 8 8
St Step ep 9 9
St Step ep 10 10
St Step ep 11 11
St Step ep 12 12
St Step ep 13 13
St Step ep 14 14
Connecting to the Access Point Console Port Connecting to the Access Point Console Port
Caution Caution
Note Note
St Step ep 1 1
St Step ep 2 2
Choose the Cisco IOS release desired, such as 12.3.11.JA. Choose the Cisco IOS release desired, such as 12.3.11.JA.
Click WIRELESS LAN Click WIRELESS LAN for an access point image file, such as c1130-k9w7-tar.123-11.JA.ta for an access point image file, such as c1130-k9w7-tar.123-11.JA.ta r r . .
If the Enter Network Password window appears, ente r your Cisco.com username and passwo If the Enter Network Password window appears, ente
OK. . OK
Click Wireless LAN Click Wireless LAN on the right side of the screen. on the right side of the screen.
Click Click DOWNLOAD DOWNLOAD. .
Read and accept the terms and conditions of the Software Download Rules. Read and accept the terms and conditions of the Software Download Rules.
On the Enter Network Password window, enter your Cisco.com username and password and click On the Enter Network Password window, enter your Cisco.com username and password and click OK
Click Save Click Save to download your image file to your hard disk. to download your image file to your hard disk.
Select the desired download location on your hard disk and click Select the desired download location on your hard disk and click Save
The console port is enabled during power up for diagnostic and monitoring purposes, which might be The console port is enabled during power up for diagnostic and monitoring purposes, which might be
helpful if the access point is unable to helpful if the access point is unable to associate to a controller. You can connect a PC to the co
using a DB-9 to RJ-45 serial cable. using a DB-9 to RJ-45 serial cable.
Be careful when handling the access point, the bottom plate might be hot. Be careful when handling the access point, the bottom plate might be hot.
The Cisco part number for the DB-9 to RJ-45 serial cable is AIR-CONCAB1200. Browse to The Cisco part number for the DB-9 to RJ-45 serial cable is AIR-CONCAB1200. Browse to
http://www.cisco.com/go/marketplace http://www.cisco.com/go/marketplace
Follow these steps to view the power up sequences by connecting to the access point console port: Follow these steps to view the power up sequences by connecting to the access point console port:
Open the access point cover (refer to the "Opening the Acc Open the access point cover (refer to the
Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and
to the COM port on a computer. The location of the access point console port is shown in Fig to the COM port on a computer. The location of the access point console port is shown in
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
Chapter 3 3 Chapter
r your Cisco.com username and passwo rd and click
associate to a controller. You can connect a PC to the co nsole port
to order a serial cable. to order a serial cable.
"Opening the Access Point Cov ess Point
Point Hardware Installation Guide
Troubleshooting Autonomous Troubleshooting Autonomous Access Access Points
rd and click
Save. .
nsole port
Cover" sectio er" section on page n on page 2-11). ). 2-11
Figure
3-19 3-19
Points
OK. .
ure 3- 3-3 3 . .