Using A Wlan Controller To Return The Access Point To Autonomous Mode - Cisco Aironet 1130AG Series Hardware Installation Manual

OL-8369-04 OL-8369-04
Returning the Access Point to Autonomous Mode Returning the Access Point to Autonomous Mode

Using a WLAN Controller to Return the Access Point to Autonomous Mode

Using a WLAN Controller to Return the Access Point to Autonomous Mode
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
Using the MODE Button to Return the Access Point to Using the MODE Button to Return the Access Point to Autonomous Mode
Note Note
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
St Step ep 5 5
St Step ep 6 6
St Step ep 7 7
St Step ep 8 8
St Step ep 9 9
Follow these steps to revert from lightweight mode to autonomous mode using a controller: Follow these steps to revert from lightweight mode to autonomous mode
Log into the CLI on the controller to which the access point is associated and enter this command: Log into the CLI on the controller to which the access point is associated and enter this command:
config ap tftp-downgrade tftp-server-ip-address config ap tftp-downgrade
(where: (where:
a) a)
tftp-server-ip-address tftp-server-ip-address
b) b) is the full path and filname of the access point image file, such as is the full path and filname of the access point image file, such
filename filename
D:/Images/ D:/Images/
c1130-k9w7-tar.123-7.JA.ta c1130-k9w7-tar.123-7.JA.ta
c) c)
access-point-name access-point-name
ocntroller.) ocntroller.)
Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED
blinking green. blinking green.
After the access point reboots, reconfigure it using the access point GUI or the CLI. After the access point reboots, reconfigure it using the access point GUI or the CLI.
Follow these steps to return a lightweight access point to autonomous mode using the Follow these steps to return a lightweight access
button and a TFTP server: button and a TFTP server:
The access point MODE button is enabled by default, but you need to verify that the MODE button is The access point MODE button is enabled by default, but you need to verify that the MODE button is
enabled (see the enabled (see the "MODE Button Se "MODE Button
Set the static IP address of the PC on which your TFTP server software runs to an address between Set the static IP address of the PC on which your TFTP server software runs to an address between
10.0.0.2 and 10.0.0.30. 10.0.0.2 and 10.0.0.30.
Make sure that the PC contains the access point image file (such as Make sure that the PC contains the access point image file (such as c1130-k9w7-tar.123-7.JA.ta
1130 series access point) in the TFTP server folder and that the TFTP server is activated. 1130 series access point) in the TFTP server folder and that the TFTP server is activated.
Rename the access point image file in the TFTP server folder to c1130-k9w7-tar.default. Rename the access point image file in the TFTP server folder to
Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable. Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Disconnect power from the access point. Disconnect power from the access point.
Press and hold the MODE Press and hold the MODE button while you reconnect power to the access point. button while you reconnect power to the access point.
Hold the Hold the MODE MODE button until the Radio LED turns red (approximately 20 to 30 seconds) and then button until the Radio LED turns red (approximately 20 to 30 seconds) and then
release. release.
Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED
blinking green. blinking green.
After the access point reboots, reconfigure it using the access point GUI or the CLI. After the access point reboots, reconfigure it using the access point GUI or the CLI.
Cisco Aironet 1130AG Series Access Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
tftp-server-ip-address filename filename access-point-name
is the IP address of the TFTP server is the IP address of the
r r
is the name that identifies the access point on the is the name that identifies the access point on the
point to autonomous mode using the access point MODE
Setting" se tting" section on page ction on page
Point Hardware Installation Guide
Chapter 4 4 Chapter Troubleshooting Lightweight Troubleshooting Lightweight Access
using a controller:
access-point-name
TFTP server
Autonomous Mode
access point MODE
4-11. . 4-11
c1130-k9w7-tar.123-7.JA.ta r for an
c1130-k9w7-tar.default.
4-9 4-9
Access Points Points
as
r for an