Issuing The Cisco Ios Command Using The Cli - Cisco Aironet 1130AG Series Hardware Installation Manual

Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access Point
3-10 3-10
Chapter Chapter 3 3 Troubleshoo Troubleshooting
T T a a b b l l e e 3 3 - - 2 2
Power Source Power Source
A A C C p p o o w w e e r r m m o o d d u u l l e e
Cisco switch that supports Intelligent Power Cisco switch that supports Intelligent Power
1 1
Management Management
Cisco switch that does not support Intelligent Cisco switch that does not support Intelligent
Power Management Power Management
2 2
Power injector Power injector
supports Intelligent Power Management supports Intelligent Power Management
2 2
Power injector Power injector
does not support Intelligent Power does not support Intelligent Power
1 1
Management Management
P P o o w w e e r r i i n n j j e e c c t t o o r r u u s s e e d d w w i i t t h h a a n n o o n n - - C C i i s s c c o o s s w w i i t t c c h h
8 8 0 0 2 2 . . 3 3 a a f f c c o o m m p p l l i i a a n n t t n n o o n n - - C C i i s s c c o o s s w w i i t t c c h h e e s s
1. 1. You should check the rele You should check the release notes for your Cisc
for Intelligent Power Management might not be currently available for for Intelligent Power Management might not be currently available for your Cisco power source.
2. 2. Powe Power inject r injector must be AIR or must be AIR-PWR
3. 3. The Cisco s The Cisco switch uses Inte witch uses Intelligent Power
4. 4. Cisco switch Cisco switches that support I es that support Intelligent Po

Issuing the Cisco IOS Command Using the CLI

Issuing the Cisco IOS Command Using the CLI
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
St Step ep 5 5
St Step ep 6 6
Hardware Installation Guide
ting Autonomous Autonomous Access Access Points Points
Refer to T Refer to T able able 3-2 for information on when to use this special Cisco IOS command and the 3-2 for information on when to use this special Cisco IOS command and the
corresponding Cisco switch power command. corresponding Cisco switch power command.
U U s s i i n n g g C C i i s s c c o o I I O O S S C C o o m m m m a a n n d d s s
1 1
used with a Cisco switch that used with a Cisco switch that
1 1
used with a Cisco switch that used with a Cisco switch that
ase notes for your Cisco power source to determine whic o power source to determine which Cisco IOS release s
-PWRINJ3 or AIR INJ3 or AIR-PWR -PWRINJ-
lligent Power Management to infor Management to inform the access po
ntelligent Power Management a wer Management always configure th
Follow these steps to issue the Cisco IOS command for your power scenario: Follow these steps to issue the Cisco IOS command for your power scenario:
Connect a PC to the access poi nt console port and use a terminal emulator to establish a session with th Connect a PC to the access poi
access point (refer to the access point (refer to the "Connecti
From the global configuration mode, enter the c From the global configuration mode, enter the c ommand below that applies to your power configuration
(see (see T T able abl e 3-2 3-2): ):
• • power inline negotiation injector installed power inline negotiation injector installed
• • no power inline negotiation injector no power inline negotiation injector
• • power inline negotiation prestandard source power inline negotiation prestandard source
• • no no power inline negotiation prestandard source power inline negotiation prestandard source
Enter exit exit to exit the global configuration mode.
Enter to exit the global configuration mode.
Enter Enter write memory write memory to save the setting to the access point memory. to save the setting to the access point memory.
Enter Enter quit quit to exit the terminal session. to exit the terminal session.
Close your terminal emulator. Close your terminal emulator.
A A c c c c e e s s s s P P o o i i n n t t
N N o o n n e e r r e e q q u u i i r r e e d d
no power inline negotiation prestandard source no power inline negotiation prestandard source
no power inline negotiation injector no power inline negotiation injector
power inline negotiation prestandard source power inline negotiation prestandard source
no power inline negotiation injector no power inline negotiation injector
3 3
None required None required
no power inline negotiation prestandard source no power inline negotiation prestandard source
power inline negotiation injector installed power inline negotiation injector installed
N N o o n n e e r r e e q q u u i i r r e e d d
N N o o n n e e r r e e q q u u i i r r e e d d
h Cisco IOS release supports Intelligent P
your Cisco power source.
INJ-FIB. FIB.
m the access point of the power injec int of the power injector being use
lways configure the use of a power e use of a power injector at the
nt console port and use a terminal emulator to establish a session with th e e
"Connecting to the Access Point Console Port" secti ng to the Access Point Console Port"
ommand below that applies to your power configuration
Low Power Condition for Autonomous Access Points Low Power Condition for Autonomous Access Points
Cisco IOS Commands Cisco IOS Commands
upports Intelligent Power Management. Su ower Management. Support
tor being used. d.
injector at the switch. switch.
section on page on on page
OL-8369-04 OL-8369-04
C C i i s s c c o o S S w w i i t t c c h h
power inline never power inline never
power inline auto power inline auto
power inline auto power inline auto
4 4
power inline never power inline never
power inline never power inline never
– –
– –
pport
3-20). ). 3-20