Low Power Condition For Lightweight Access Points; Intelligent Power Management - Cisco Aironet 1130AG Series Hardware Installation Manual

OL-8369-04 OL-8369-04

Low Power Condition for Lightweight Access Points

Low Power Condition for Lightweight Access Points

Low Power Condition for Lightweight Access Points Low Power Condition for Lightweight Access Points
Warning Warning
Note Note
Note Note

Intelligent Power Management

Intelligent Power Management
Note Note
This product must be connected to a Power over Ethernet (PoE) This product must be connected to
or an IEC60950 compliant limited power source. or an IEC60950 compliant limited power s
The lightweight access point can be powered from the 48-VDC power module or from an in-line power The lightweight access point can be powered from the 48-VDC power module or from an in-line power
source. The access point supports the IEEE 802.3af power standard, Cisco Pre-Standard PoE protocol, source. The access point supports the IEEE 802.3af power standard, Cisco Pre-Standard PoE protocol,
and Cisco Intelligent Power Management for in-li and Cisco Intelligent Power Management for in-line power sources.
For full operation, the access point requires 12.95 W of power. The power module and Cisco Aironet For full operation, the access point requires 12.95 W of power. The power module and Cisco Aironet
power injectors are capable of supplying the required power for full operation, but some inline power power injectors are capable of supplying the required power for full operation, but some inline power
sources are not capable of supplying 12.95 W. Also, some high-power inline power sources, might not sources are not capable of supplying 12.95 W. Also, some high-power inline power sources, might not
be able to provide 12.95 W of power to all ports at the same time. be able to provide 12.95 W of power to all ports at the same time.
An 802.3af compliant switch (Cisco or non-Cisco) is capable of supplying sufficient power for full An 802.3af compliant switch (Cisco or non-Cisco) is capable of supplying sufficient power for full
operation. operation.
If your access point is conn ected to in-line power, do not connect the power module If your access point is conn ected to in-line power, do not connect the power module to the access point.
Using two power sources on the access point might cause the access point to shut down to protect internal Using two power sources on the access point might cause the access point to shut down to protect internal
components and might cause the switch to shut down the port to which the access point is connected. If components and might cause the switch to shut down the port to which the access point is connected. If
your access point shuts down, you must remove all power and reconnect only a single power source. your access point shuts down, you must remove all power and reconnect only a single power source.
On power up, the access point is placed into low power mode (both radios are disabled), Cisco IOS On power up, the access point is placed into low power mode (both radios are disabled), Cisco IOS
software loads and runs, and power negotiation determines if sufficient power is available. If there is software loads and runs, and power negotiation determines if sufficient power is available. If there is
sufficient power then both radios are turned on; otherwise, the access point remains in low power mode sufficient power then both radios are turned on; otherwise, the access point remains in low power mode
with one or both radios disabled to prevent a possible over-current condition. In low power mode, the with one or both radios disabled to prevent a possible over-current condition. In low power mode, the
access point activates the Status LED low power error indication (see the "Checking the Lightweight access point activates the Status LED low power error indication (see the
Access Access Po Point LEDs" sect int LEDs" section on page ion on page
The access point requires 12.95 W of power for full power operation with both radios, but only needs The access point requires 12.95 W of power for full power operation with both radios, but only needs
6.3 W of power when operating in low power mode with both radios disabled. To help avoid an 6.3 W of power when operating in low power mode with both radios disabled. To help avoid an
over-current condition with low power sources and to optimize power usage on Cisco switches, Cisco over-current condition with low power sources and to optimize power usage on Cisco switches, Cisco
developed Intelligent Power Management, which uses Cisco Discovery Protocol (CDP) to allow developed Intelligent Power Management, which uses Cisco Discovery Protocol (CDP) to allow
powered devices (such as your access point) to negotiate with a Cisco switch for sufficient power. powered devices (such as your access point) to negotiate with a Cisco switch for sufficient power.
The access point supports Intelligent Power Management and as a result of the power negotiations, the The access point supports Intelligent Power Management and as a result of the power negotiations, the
access point will either enter full power mode or remain in low power mode with one or both radios access point will either enter full power mode or remain in low power mode with one or both radios
disabled. disabled.
Independent of the power negotiations, the access point hardware also uses the 802.3af classification Independent of the power negotiations, the access point hardware also uses the 802.3af classification
scheme to indicate the power required from the power sour ce. However, the power source cannot report scheme to indicate the power required from the power sour
the power available to the access point unless the power source also supports Intelligent Power the power available to the access point unless the power source also supports Intelligent Power
Management. Management.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
Chapter 4 4 Chapter
a Power over Ethernet (PoE) IEEE 802.3af compliant power source
ource.
Statement 353 Statement 353
ne power sources.
4-2). ). 4-2
ce. However, the power source cannot report
Point Hardware Installation Guide
Troubleshooting Lightweight Troubleshooting Lightweight Access Access Points
IEEE 802.3af compliant power source
to the access point.
"Checking the Lightweight
4-5 4-5
Points