Checking Basic Settings; Default Ip Address Behavior; Default Ssid And Radio Behavior - Cisco Aironet 1130AG Series Hardware Installation Manual

OL-8369-04 OL-8369-04

Checking Basic Settings

Checking Basic Settings
T T a a b b l l e e 3 3 - - 1 1 L L E E D D S S i i g g n n a a l l s s ( ( c c o o n n t t i i n n u u e e d d ) )
Message type Message type
B B o o o o t t l l o o a a d d e e r r e e r r r r o o r r s s
Checking Basic Settings Checking Basic Settings

Default IP Address Behavior

Default IP Address Behavior

Default SSID and Radio Behavior

Default SSID and Radio Behavior
C C a a b b l l e e B B a a y y A A r r e e a a
E E t t h h e e r r n n e e t t L L E E D D R R a a d d i i o o L L E E D D
R R e e d d R R e e d d
O O f f f f R R e e d d
O O f f f f A A m m b b e e r r
A A m m b b e e r r O O f f f f
R R e e d d O O f f f f
A A m m b b e e r r A A m m b b e e r r
R R e e d d A A m m b b e e r r
A A m m b b e e r r A A m m b b e e r r
Mismatched basic settings are the most common causes of lost connectivity with wireless clients. If the Mismatched basic settings are the most common causes of lost connectivity with wireless clients. If the
access point does not communicate with client devices, check the following areas. access point does not communicate with client devices, check the following areas.
When you connect an 1130AG access point running Cisco IOS Release 12.3(2)JA or later software with When you connect an 1130AG access point running Cisco IOS Release 12.3(2)JA or later software with
a default configuration to your LAN, the access point requests an IP address from your DHCP server, a default configuration to your LAN, the access point requests an IP address from your DHCP server,
and if it does not receive an IP address, it continues to send requests indefinitely. and if it does not receive an IP address, it continues to send requests indefinitely.
In Cisco IOS Relese 12.3 In Cisco IOS Relese 12.3 (2)JA2 and earlier, the access point radios are enabled by default and the default (2)JA2 and earlier, the access point radios are enabled by default and the default
SSIDs are tsunami SSIDs are tsunami . .
In Cisco IOS Release 12.3(4)JA and later, the access point radios are disabled by default, and there are In Cisco IOS Release 12.3(4)JA and later, the access point radios are disabled by default, and there are
no default SSIDs. You must create an SSID and enable the radio before the access point will allow no default SSIDs. You must create an SSID and enable the radio before the access point will allow
wireless associations from other devices. These changes to the default configuration improve the wireless associations from other devices. These changes to the default configuration improve the
security of newly installed access points. Refer to the Cisco IOS Software Configuration Guide for Cisco security of newly installed access points. Refer to the
Airone Aironet Access Points t Access Points for instructions on configuring the SSID and the for instructions on configuring the SSID and the "Enable Radio Interfaces" section
on on p pag age e 3-5 3-5 for instructions on enabling the radio interfaces. for instructions on enabling the radio interfaces.
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
Chapter 3 3 Chapter
T T o o p p o o f f U U n n i i t t
S S t t a a t t u u s s L L E E D D Meaning Meaning
R R e e d d D D R R A A M M m m e e m m o o r r y y t t e e s s t t f f a a i i l l u u r r e e . .
B B l l i i n n k k i i n n g g r r e e d d Flash file system failure. Flash file system failure.
and blue and blue
B B l l i i n n k k i i n n g g r r e e d d Environment variable (EN Environment variable (ENV V AR) failure.
and and
blue-green blue-green
B B l l i i n n k k i i n n g g r r e e d d Bad MAC address. Bad MAC address.
and yellow and yellow
B B l l i i n n k k i i n n g g r r e e d d Ethernet failure during image recovery. Ethernet failure during image recovery.
and off and off
B B l l i i n n k k i i n n g g r r e e d d Boot environment error. Boot environment error.
and off and off
B B l l i i n n k k i i n n g g r r e e d d No Cisco IOS image file. No Cisco IOS image file.
and off and off
B B l l i i n n k k i i n n g g r r e e d d Boot failure. Boot failure.
and off and off
Cisco IOS Software Configuration Guide for Cisco
Point Hardware Installation Guide
Troubleshooting Autonomous Troubleshooting Autonomous Access Access Points
AR) failure.
"Enable Radio Interfaces" section
3-3 3-3
Points