Mounting The Access Point Below A Suspended Ceiling - Cisco Aironet 1130AG Series Hardware Installation Manual

OL-8369-04 OL-8369-04

Mounting the Access Point Below a Suspended Ceiling

Mounting the Access Point Below a Suspended Ceiling
Mounting the Access Point Below a Suspended Ceiling Mounting the Access Point Below a Suspended Ceiling
St Step ep 1 1
St Step ep 2 2
St Step ep 3 3
St Step ep 4 4
St Step ep 5 5
St Step ep 6 6
St Step ep 7 7
Cisco Aironet 1130AG Series Access Point Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
Y Y ou ou should review should review Fig Figure ure 2-7 before beginning the mounting process. 2-7
F F i i g g u u r r e e 2 2 - - 7 7 A A d d j j u u s s t t a a b b l l e e T T - - R R a a i i l l C C l l i i p p s s
2 2
3 3
3 3 8 8 2 2 4 4
MM MM
INCH INCH
1 1 - - 1 1 / / 2 2 1 1 5 5 / / 1 1 6 6
CEILING CEILING
GRID GRID
A A B B
WIDTH WIDTH
2 2
1 1
1 1
T T -rail locking -rail locking screws screws
2 2 Mounting plate screw holes Mounting plate screw holes
Follow these steps to mount your access point on a suspended ceiling: Follow these steps to mount your access point on a suspended ceiling:
Decide where you want to mount the access point on your suspended ceiling. Decide where you want to mount the access point on your suspended ceiling.
Select the appropriate adjustable T-rail clip for your suspended ceiling and ope Select the appropriate adjustable T-rail clip for your suspended ceiling and ope n the clip to the maximum
(see (see Fig Figure ure 2-4). ). 2-4
Place the T-rail clip over the T-rail and close it (see Fi Figur Place the T-rail clip over the T-rail and close it (see
Tighten the two T-rail locking screws to prevent the T-rail clip from sliding along the T-rail. Tighten the two T-rail locking screws to prevent the T-rail clip from sliding along the T-rail.
Observe the T-rail width detent letter (A, B, or C) that corresponds to the T-rail width. Observe the T-rail width detent letter (A, B, or C) that corresponds to the T-rail width.
Align the corresponding (A, B, or C) holes on the mounting plate over the T-rail mounting plate holes. Align the corresponding (A, B, or C) holes on the mounting plate over the T-rail mounting plate holes.
Hold the mounting plate and insert a 6 x 32 x 1/4 in. flat head screw into each of the four corresponding Hold the mounting plate and insert a 6 x 32 x 1/4 in. flat head screw into each of the four corresponding
(A, B, or C) holes and tighten. (A, B, or C) holes and tighten.
Hardware Installation Guide
before beginning the mounting process.
1 1
2 2
1 1 5 5
9 9 / / 1 1 6 6
C C
C C B B
6 6 1 1 / / 9 9 6 6 1 1 / / 5 5 1 1
5 5 1 1 4 4 2 2
2 2
3 3
T-rail width detents (A, B, or C) T-rail width detents (A, B, or C)
gure
Chapter Chapter 2 2 Installing Installing the
H H T T D D I I W W
A A
D D I I R R G G
G G N N I I L L I I E E C C
2 2 / / 1 1 - - 1 1 H H C C N N I I
M M M M
8 8 3 3
3 3
8 8
5 5
7 7
1 1
2 2
1 1
n the clip to the maximum
e 2-4 2-4) to the appropriate (A, B, or C) detent. ) to the appropriate (A, B, or C) detent.
2-13 2-13
the Access Access Point Point