Cisco Aironet 1130AG Series Hardware Installation Manual page 64

OL-8369-04 OL-8369-04
Low Power Condition for Autonomous Access Points Low Power Condition for Autonomous Access Points
• • %CDP_PD-4-POWER_OK: Full Power - INJECTOR_DETECTED_PD inline power source—This %CDP_PD-4-POWER_OK: Full Power - INJECTOR_DETECTED_PD inline power source—This
message indicates the access point is operating at full power because it has detected a CDP packet message indicates the access point is operating at full power because it has detected a CDP packet
from another Cisco powerable device (PD). from another Cisco powerable device (PD). The access point power is being suppl
injector or a non-Cisco power source because a Cisco power source does not transmit this type of injector or a non-Cisco power source because a Cisco power source does not transmit this type of
CDP packet. CDP packet.
• • %CDP_PD-4-POWER_OK: Full Power - INJECTOR_DETECTED_MULTIPLE_MACS_ON_ %CDP_PD-4-POWER_OK: Full Power - INJECTOR_DETECTED_MULTIPLE_MACS_ON_
HUB inline power source—This message indicates the access point is operating at full power HUB inline power source—This message indicates the access point is operating at full power
because it has detected multiple Cisco devices. The access point power is being supplied from a because it has detected multiple Cisco devices. The access point power is being supplied from a
power injector or a non-Cisco power source because a Cisco power source does not forward CDP power injector or a non-Cisco power source because a Cisco power source does not forward CDP
packets. packets.
• •
%CDP_PD-4-POWER_OK: Full Power - NON_CISCO-NO_CDP_RECEIVED inline power %CDP_PD-4-POWER_OK: Full Power - NON_CISCO-NO_CDP_RECEIVED inline power
source—This message indicates the access point is operating at full power because it has not source—This message indicates the access point is operating at full power because it has not
received any CDP packets within the timeout period. This condition indicates your access point is received any CDP packets within the timeout period. This condition indicates your access point is
connected to a non-Cisco power source. connected to a non-Cisco power source.
Note Note To prevent possible over-current conditions, the power source must be an IEEE 802.3af To prevent possible over-current conditions, the power source must be an
compliant power source or an IEC60950 compliant limited power source. compliant power source or an IEC60950 compliant limited power source.
• •
%CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED inline power source—This %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED inline power source—This
message indicates the access point is in low power mode with all radios disabled because the Cisco message indicates the access point is in low power mode with all radios disabled because the Cisco
power source has indicated it is not capable of supplying sufficient power to the access point. power source has indicated it is not capable of supplying sufficient power to the access point.
Note Note A Cisco power injector might be required. A Cisco power injector might be required.
• • %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_ %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_
CONFIGURED < plat CONFIGURED < plat form n form n ame
low power mode with all radios disabled and has detected a CDP device that is unable to supply low power mode with all radios disabled and has detected a CDP device that is unable to supply
sufficient power to the access point. sufficient power to the access point.
The< platform name> The< platform name> indicates the CDP device detected by the access point. The indicates the CDP device detected by the access point. The <MAC address>
indicates the MAC address of the CDP device, typically, the switch port. indicates the MAC address of the CDP device, typically, the switch port.
Note Note A Cisco power injector might be required. A Cisco power injector might be required.
Following the low power status message, two extra messages are displayed on the console port or Following the low power status message, two extra messages are displayed on the console port or
when using a Telnet session that identify the actions needed to resolve this low power problem: when using a Telnet session that identify the actions needed to resolve this low power problem:
V V erify the required power injector erify the required power injector is installed on this po
– –
(where < (where < plat plat form form name name > indicates the CDP device detected by the access point and
< < Ethe Ethe rnet rnet port port > indicates the Ethernet port of the CDP device. > indicates the Ethernet port of the CDP device.
If a power injector is installed, issue the command: power inline negotiation injector installed. If a power injector is installed, issue the command: power inline negotiation injector installed.
– –
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide Cisco Aironet 1130AG Series Access
Chapter 3 3 Chapter
The access point power is being suppl ied from a power
ame > (< > (< MAC address MAC address >)—This message indicates the access point is in >)—This message indicates the access point is in
is installed on this po rt: <
> indicates the CDP device detected by the access point and
Point Hardware Installation Guide
Troubleshooting Autonomous Troubleshooting Autonomous Access Access Points
ied from a power
IEEE 802.3af
<MAC address>
rt: < plat plat form form name name > (< > (< Ethe Ethe rnet p
3-7 3-7
Points
rnet port ort > ). >).