Xcommand Video Pip Activespeaker Set; Xcommand Video Pip Presentation Set; Xcommand Video Picturelayoutset; Xcommand Video Previewfilmstrip Set - Cisco TelePresence SX20 Codec Reference Manual

Cisco TelePresence SX20 Codec
Contents Introduction

xCommand Video PIP ActiveSpeaker Set

Sets position for the active speakers PiP (picture in picture).
Position: Predefined positions.
CenterLeft: The ActiveSpeaker PiP appears on the left side of the screen, in center.
CenterRight: The ActiveSpeaker PiP appears on the right side of the screen, in center.
LowerLeft: The ActiveSpeaker PiP appears in the lower left corner of the screen.
LowerRight: The ActiveSpeaker PiP appears in the lower right corner of the screen.
UpperCenter: The ActiveSpeaker PiP appears on top of the screen, in center.
UpperLeft: The ActiveSpeaker PiP appears in the upper left corner of the screen.
UpperRight: The ActiveSpeaker PiP appears in the upper right corner of the screen.
Requires user role: ADMIN
Parameters:
Position(r): <CenterLeft/CenterRight/LowerLeft/LowerRight/UpperCenter/UpperLeft/UpperRight>
Example:
xCommand Video PIP ActiveSpeaker Set Position: UpperRight

xCommand Video PIP Presentation Set

Sets position for the presentation PiP (picture in picture).
Position: Predefined positions.
CenterLeft: The presentation PiP appears on the left side of the screen, in center.
CenterRight: The presentation PiP appears on the right side of the screen, in center.
LowerLeft: The presentation PiP appears in the lower left corner of the screen.
LowerRight: The presentation PiP appears in the lower right corner of the screen.
UpperCenter: The presentation PiP appears on top of the screen, in center.
UpperLeft: The presentation PiP appears in the upper left corner of the screen.
UpperRight: The presentation PiP appears in the upper right corner of the screen.
Requires user role: ADMIN
Parameters:
Position(r): <CenterLeft/CenterRight/LowerLeft/LowerRight/UpperCenter/UpperLeft/UpperRight>
Example:
xCommand Video PIP Presentation Set Position: LowerLeft
SX20 Codec API Reference Guide TC7.3, OCTOBER 2015.
D14949.13
About the API xConfiguration

xCommand Video PictureLayoutSet

xCommand Video PreviewFilmstrip Set

126
xCommand xCommand
Select the screen layout mode.
Target: Select if the target is the local layout or the remote layout.
CallId: The CallID is returned when the xCommand Dial command is run. During the call you can run
the xStatus Call command to see the CallId.
LayoutFamily: Select a layout family.
CustomLayoutName: Enter a name for the layout.
Requires user role: USER
Parameters:
Target: <local/remote>
CallId: <0..65534>
LayoutFamily(r): <auto/custom/equal/fullscreen/overlay/presentationlargespeaker/
presentationsmallspeaker/prominent/single/speaker_full>
CustomLayoutName: <S: 1, 128>
Example:
xCommand Video PictureLayoutSet Target: Local LayoutFamily: equal
Moves the location of the filmstrip associated with the layouts used in presentation preview mode.
Not in use in this software version.
LowerCenter: The preview appears on the bottom of the screen, in center.
LowerLeft: The preview appears in the lower left corner of the screen.
LowerRight: The preview appears in the lower right corner of the screen.
UpperCenter: The preview appears on top of the screen, in center.
UpperLeft: The preview appears in the upper left corner of the screen.
UpperRight: The preview appears in the upper right corner of the screen.
Requires user role: ADMIN
Parameters:
Position(r): <LowerCenter/LowerLeft/LowerRight/UpperCenter/UpperLeft/UpperRight>
Example:
xCommand Video PreviewFilmstrip Set Position: LowerCenter
API Reference Guide
xStatus Appendices
Copyright © 2015 Cisco Systems, Inc. All rights reserved.