ABB IP Touch 7 Manual page 8

2.21.52
2.21.53
2.21.54
2.21.55
2.21.56
2.21.57
2.21.58
2.21.59
2.21.60
2.21.61
2.21.62
2.21.63
2.21.64
2.21.65
2.21.66
2.21.67
2.21.68
2.21.69
2.21.70
2.21.71
2.21.72
2.21.73
2.21.74
2.21.75
2.21.76
2.21.77
2.21.78
2.21.79
2.21.80
2.21.81
2.21.82
2.21.83
2.21.84
2.21.85
2.21.86
2.21.87
2.21.88
2.21.89
2.21.90
2.21.91
2.21.92
2.21.93
2.21.94
2.21.95
2.21.96
2.21.97
2.21.98
2.21.99
2.21.100
2.21.101
Product manual 2CKA001473B5023
Cooling control - P-component (x 0.1°C) .................................................................................157
Cooling control - I-component (min.) .......................................................................................157
Cooling control - Extended settings ...........................................................................................157
Basic stage cooling ...................................................................................................................158
Basic stage cooling - Status object cooling .............................................................................158
Basic stage cooling - Mode of the control value ......................................................................158
Basic stage cooling - Hysteresis (x 0.1°C) ..............................................................................159
Basic stage cooling - Cyclic sending of the control value (min) ...............................................159
Basic stage cooling - PWM cycle cooling (min) .........................................................................160
Basic stage cooling - Maximum control value (0 - 255) ...........................................................160
Basic stage cooling - Minimum control value for basic load (0 to 255) ....................................160
Settings of basic load - Minimum control value for basic load > 0 ...........................................161
Basic load settings - Basic load active when controller is off ...................................................161
Setpoint settings - Setpoint temperature for cooling comfort (°C) ...........................................162
Setpoint settings - Increase for standby cooling (°C) ..............................................................162
Setpoint settings - Increase for ECO cooling (°C) ...................................................................162
Setpoint settings - Set-point temperature for heat protection (°C) ...........................................163
Setpoint settings - Send current setpoint ................................................................................163
Setpoint settings - Cyclic sending of the current set-point temperature (min) ..........................163
Setpoint adjustment - Maximum manual increase during cooling mode (0 - 9°C) ...................163
Setpoint adjustment - Maximum manual reduction during cooling mode (0 - 9°C) ..................164
Setpoint adjustment - Resetting of the manual adjustment for receipt of a basic setpoint .......164
Setpoint adjustment - Resetting the manual adjustment for change of operating mode ..........164
Setpoint adjustment - Resetting the manual adjustment via object .........................................165
Setpoint adjustment - Permanent storage of on-site operation ...............................................165
Setpoint adjustment - Permanent storage of on-site operation ...............................................165
Temperature reading - Inputs of temperature reading .............................................................165
Temperature reading - Inputs of weighted temperature reading .............................................166
Temperature reading - Weighting of internal measurement (0 to 100%) .................................166
Temperature reading - Weighting of external measurement (0 to 100%) ................................166
Temperature reading - Weighting of external measurement 2 (0 to 100%) .............................166
Temperature reading - Cyclic sending of the actual temperature (min) ...................................166
Temperature reading - Difference of value for sending the actual temperature (x 0.1°C) ........167
Temperature reading - Adjustment value for internal temperature measurement (x 0.1°C) ....167
Temperature reading - Monitoring time for temperature reading (0 = no monitoring) (min) .....168
Temperature reading - Control value for fault (0 - 255) ...........................................................168
Alarm functions - Condensate water alarm ................................................................................168
Alarm functions - Dew point alarm ..........................................................................................169
Alarm functions - Frost alarm temperature for HVAC and RHCC status (°C) ..........................169
Alarm functions - Heat alarm temperature for RHCC status (°C) ............................................169
Summer compensation .............................................................................................................169
Summer compensation - Summer compensation ...................................................................170
Summer compensation -- (Lower) Starting temperature for summer compensation (°C) ........171
Summer compensation - Offset of the set-point temperature for the entry into summer
compensation (x 0.1°C) .............................................................................................................171
Summer compensation - (Upper) exit temperature for summer compensation (°C) ................171
Summer compensation - Offset of the set-point temperature for the exit from summer
compensation (x 0.1°C) .............................................................................................................172
Control of additional cooling stage - Cooling type ...................................................................173
Control of additional cooling stage - P-component (x 0.1°C) ...................................................173
Control of additional cooling stage - P-component (min) .........................................................174
Combined heating and cooling modes ......................................................................................174
Table of contents
│8