Toro Multi Pro 1750 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Paint Sprayer
  5. Multi Pro 1750
  6. Operator's manual
Toro Multi Pro 1750 Operator's Manual

Toro Multi Pro 1750 Operator's Manual

Turf sprayer
Hide thumbs Also See for Multi Pro 1750:
Table of Contents

Advertisement

Quick Links

Download this manual
EU Compliance Kit
2015 and After Multi Pro
Model No. 41155—Serial No. 315000001 and Up
Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers of
your product ready.
Figure 1
model and serial numbers on the product.
Model No.
Serial No.
Note: Determine the left and right sides of the machine
from the normal operating position.
© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
illustrates the location of the
Figure 1
Register at www.Toro.com.
®
1750 Turf Sprayer
The EU Compliance Kit is designed to meet German safety
requirements by enabling operators to clean out residual
chemicals from the sprayer system and clean the external
machine while bypassing the chemical tank. It is a dedicated
kit for a turf spray application vehicle and is intended to
be used by professional, hired operators in commercial
applications.
This product complies with all relevant European directives.
For details, please see the Declaration of Incorporation (DOI)
at the back of this publication.
Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe products,
you are responsible for operating the product properly and
safely.
Safety
This manual identifies potential hazards and has safety
messages identified by the safety alert symbol
which signals a hazard that may cause serious injury or death
if you do not follow the recommended precautions.
1. Safety alert symbol
This manual uses 2 other words to highlight information.
Important calls attention to special mechanical information
and Note emphasizes general information worthy of special
attention.
Also read the safety and operation instructions in the vehicle
Operator's Manual.
Original Instructions (EN)
All Rights Reserved *3393-275* A
Printed in the USA
Form No. 3393-275 Rev A
Operator's Manual
(Figure
Figure 2
2),

Advertisement

Table of Contents
loading

Related Manuals for Toro Multi Pro 1750

Summary of Contents for Toro Multi Pro 1750

  • Page 1 1750 Turf Sprayer Model No. 41155—Serial No. 315000001 and Up Operator's Manual Whenever you need service, genuine Toro parts, or additional The EU Compliance Kit is designed to meet German safety information, contact an Authorized Service Dealer or Toro requirements by enabling operators to clean out residual...
  • Page 2 Chemical Safety Hand Sprayer Safety • Do not aim the hand sprayer at any person or animal. WARNING Fluids under high pressure can penetrate skin and cause severe injury, possibly resulting in amputation or death. Chemical substances used in the spray system may Hot liquids and chemicals can also cause burns or injury.
  • Page 3 Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 120-0687 120-0673 1. Valve, open 2. Valve, closed 1. Boom spray 3.

  • Page 4: Table Of Contents

    Procedure Description Qty. 90° barbed fitting (3/4 inch NPT x 3/4 inch) Plastic flange nut Bulkhead fitting Install the rinse nozzle. Rinse nozzle Bushing Rinse vane Shoulder bolt Carriage bolt (3/8 x 1 inch) Flanged Locknuts (3/8 inch) Rinse-pump mounting bracket Straight-barbed fitting (1/2 inch NPT x 1/2 inch) Nipple (1/2 inch NPT)

  • Page 5: Inch)

    Procedure Description Qty. Inlet hose 2.5 x 66 cm (1 x 26 inch) Hose clamp 90° hub fitting Large O-ring T-Fitting (upper) Install the upper T-fitting assembly. Retainer Reducer hub Small O-ring Transfer hose 1.9 x 61 cm (3/4 x 24 inch) Hub connector Hose clamp...

  • Page 6: Plastic Flange Nut

    Preparing the Machine Installing the Rinse Tank No Parts Required Parts needed for this procedure: Carriage bolt (5/16 x 1 inch) Procedure Spray-gun bracket 1. Move the sprayer onto a level surface, set the parking Clamp brake, stop the pump, stop the engine, and remove the Flanged locknut (5/16 inch) ignition key.
  • Page 7 Note: Retain the bolt (3/8 x 5 inch), washers, and flanged locknut; discard the short carriage bolt and locknut holding the R-clamp in place. Figure 3 1. Fresh water tank 3. Flanged head bolts 2. Mounting bracket 3. Remove the tank from the machine (Figure Figure 5 Note: Retain the fresh water tank and flanged head...
  • Page 8 Installing the Tank 4. Install 1 carriage bolt (3/8 x 1-1/4 inch) in the upper-inboard holes of the right, front tank strap 1. Install the bulkhead fitting into the rinse tank as (Figure follows: Note: Loosely thread a flanged locknuts (3/8 inch) A.
  • Page 9 G014260 Figure 12 1. Retainer 3. 90° barbed fitting G014229 2. Bulkhead fitting 2. Release the 2 latches that secure the guard behind the Figure 10 seat to the chassis and remove the guard from the 3. Filler cap 1. Bulkhead fitting (wire machine (Figure 13).
  • Page 10 Figure 14 1. Left tank bracket (slotted 3. Carriage bolt (3/8 x 1 inch) flange angled down from right to left) Figure 15 2. Flanged locknut (3/8 inch) 1. Flanged locknut (3/8 inch) 4. Right tank bracket (slotted flange angled down from left to right) 5.

  • Page 11: Rinse Nozzle

    Installing the Nozzles Note: Apply PTFE tape to the threads of the taper-threaded fittings used in the sprayer and rinse systems. 1. Assemble the 2 rinse nozzles as shown in Figure Installing the Rinse Nozzles Parts needed for this procedure: 90°...

  • Page 12: Carriage Bolt (3/8 X 1 Inch)

    5. Install a 90° barbed fitting (3/4 inch NPT x 3/4 inch) 2. Install 1 carriage bolt (3/8 x 1 inch) in the onto each of the threaded openings of the rinse-nozzle upper-inboard holes of the right, rear tank strap (Figure bulkheads (Figure...

  • Page 13: Bolt (1/4 X 1-3/4 Inch)

    g024704 Figure 21 1. Straight-barbed fitting (1/2 3. Nipple (1/2 inch NPT x 1/2 g025042 inch NPT x 1/2 inch) inch) Figure 23 2. Pressure filter 1. Serrated-flange nut (1/4 5. Rinse-pump cover inch) 2. Assemble the pressure-filter assembly onto the rinse 2.

  • Page 14: 4-Way Valve

    2. Insert 4 bolts (6 x 16 mm) and 4 washers (6 mm) into the slots of the 4-way valve (Figure 25). Assembling and Mounting the 4-Way Valve Parts needed for this procedure: 4-way valve Straight-barbed fitting(1 inch NPT x 3/4 inch) 90-degree barbed fitting (1 inch NPT x 3/4 inch) Straight-barbed fitting (3/4 inch NPT x 1/2 inch) Reducer fitting (1 inch NPT x 3/4 inch NPT)

  • Page 15: Fuse, 40-Amp

    g024700 Figure 27 1. Flange locknuts (5/16 3. Faceplate bracket Figure 28 inch) 2. Flange bolts (5/16 x 1 1. Prop rod (operator’s seat) 4. Carriage bolt inch) 2. Flanged locknut 5. Positive battery cable 3. Positive battery terminal 2. Remove the flanged locknut, carriage bolt, and positive battery cable from the battery (Figure 28).

  • Page 16: Ball Valve

    6. Remove the plastic tie that secures the rinse tank connector to the wiring bundle and route the connector to the opening that you made in the console. 7. Through the opening in the console, connect the 8-pin connector of the 3-position rocker switch into the 8-socket rinse tank connector (Figure 29).
  • Page 17 g024826 Figure 33 1. Bolt (5/16 x 5/8 inch) 3. Straight-barbed fitting (1-1/4 inch NPT x 3/4 inch) 2. Ball valve bracket 4. Ball valve 6. Install the ball valve and valve mount bracket to the machine with 2 hex-head bolts (6 x 16 mm) and 2 flange nuts (6 mm) (Figure 34).
  • Page 18 Installing the Upper Tee Assembly Parts needed for this procedure: Inlet hose 2.5 x 66 cm (1 x 26 inch) Hose clamp 90° hub fitting Large O-ring T-Fitting (upper) Retainer Reducer hub Small O-ring Transfer hose 1.9 x 61 cm (3/4 x 24 inch) Hub connector Removing the Inlet Hose 1.
  • Page 19 Assembling the Upper T-fitting, Inlet Hose and Ball Valve Hose Note: To insert the barbed fitting into the hose more easily, apply a light coat of a non-petroleum-based lubricant, such as vegetable oil to the barbed end of the fitting. 1.
  • Page 20 Installing the Upper T-fitting and Inlet 3. Install the upper T-fitting onto the hub connector and secure the fitting and connector with the retainer Hose (Figure 39) that you removed in step Removing 1. Install the 2 large O-rings into the O-ring grooves at the Inlet Hose (page 18).
  • Page 21 Installing the Hose between the Upper T-fitting and the Ball Valve Parts needed for this procedure: Hose clamp Figure 42 Retainer 1. Transfer hose 1.9 x 61 cm 3. Straight-barbed fitting (ball (3/4 x 24 inch) valve) 2. Hose clamp Procedure Note: To insert the barbed fitting into the hose more easily, 4.
  • Page 22 Installing the Hose Between the Pressure-Filter Assembly and the 4-Way Valve Parts needed for this procedure: Hose 1.9 x 61 cm (3/4 x 24 inch) Hose clamp Procedure Figure 43 Note: To insert the barbed fitting into the hose more easily, 1.
  • Page 23 Installing the Rinse Nozzle Hoses Parts needed for this procedure: Hose 1.9 x 48.3 cm (3/4 x 19 inch) Hose 1.9 x 61 cm (3/4 x 24 inch) Tee fitting Hose clamp Figure 46 Procedure 1. Hose clamp 3. 90° barbed fitting Note: To insert the barbed fitting into the hose more easily, 2.
  • Page 24 Connecting the Spray Hose and Gun Parts needed for this procedure: Hose 1.3 x 762 cm (1/2 x 300 inch) Spray gun Hose clamp Figure 48 Spray gun barbed fitting 1. Straight barbed-fitting 3. Hose 1.3 x 762 cm (1/2 x 300 inch) 2.
  • Page 25 Installing Decals Parts needed for this procedure: Decal (120-0673) Decal (120–0687) Procedure Figure 49 1. Thoroughly clean the surface of the 4-way valve bracket 1. Hose conduit 3. Hose clamp and ball valve bracket (Figure 51 Figure 52). 2. Straight-barbed fitting 4.
  • Page 26 Operation Tank Clean Rinse Kit Operation Using the Tank Clean Rinse Kit creates a rinsate; a diluted solution of residual chemicals. In many cases it is appropriate to apply the rinsate onto the treated areas. However, before doing so, check with the manufacturer of the chemical to ensure that the application of a diluted solution to the treated areas will not adversely affect the performance of the product.
  • Page 27 • This is the boom configuration (Figure 55). Use this configuration to spray rinse water out of the booms. Important: Do not set the ball valve in this position when you operate the main chemical pump. Figure 55 4–way valve + Ball Valve Controls rinse tank contents into the main tank.
  • Page 28 After 100 operating hours, inspect all hoses and O–rings. the following procedures: Replace any damaged parts. Important: Dispose of the rinseate as required by Contact your Authorized Toro Dealer to obtain replacement Federal, State and Local regulations parts. • Spray the rinsate through the booms until the main tank is empty.
  • Page 29 Notes:...
  • Page 30 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
  • Page 31 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
  • Page 32 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.

This manual is also suitable for:

41155315000001

Table of Contents