Canon iPF9000S Troubleshooting Manual page 56

Panel display
Code
(last 4
Large LCD
digits)
2E33 Roll Paper
(Paper type)
(Paper size)
Load Roll Paper
Stop Printing
Roll 1(Upper)
(Paper type)
(Paper size)
Press Load/Eject
and load a roll.
2E34 Roll 2 (Lower)
(Paper type)
(Paper size)
Press Load/Eject
and load a roll.
Roll 2 (Lower)
is selected.
Press Load/Eject
and load a roll.
2E35 Roll printing
is selected.
Roll printing
is selected.
Press Load/Eject
and load a roll.
2E36 Roll printing
is selected.
Press Load/Eject
and load a roll.
2E37 Roll printing
is selected.
Roll 1 (Upper)
is selected.
Press Load/Eject
and load a roll.
2E38 Roll 2 (Lower)
is selected.
Press Load/Eject
and load a roll.
2E39 The Roll 2 (Lower) is
empty.
Lift the release
lever and replace
the roll.
The roll (XX) is empty.
Press OK.
Explanation/Detection sequence
Small LCD
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When paper has not been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an error
of upper roll occurs.
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When no paper has been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an error
of upper roll (2E33) occurs.
Paper mismatch (roll paper)
No roll paper has been fed when a job with
a roll paper specification is received.
When no paper has been loaded on either
upper or lower slot, and the feeding slot is
set to [Automatic] in the job setting, an error
of upper roll (2E33) occurs.
* This is a message that appears when
paper type/ size specification does not exist
due to HPGL format etc.
Paper mismatch (roll paper)
No roll paper has been fed when performing
internal printing.
Paper mismatch (roll paper) (lower)
No roll paper was fed when internal printing
with the specified roll paper (lower) was
started.
Paper mismatch (roll paper) (Upper)
No roll paper has been fed when a job with
roll paper specification is received.
Paper mismatch (roll paper)
No roll paper was fed when the job specified w
upper roll paper was received.
Paper mismatch (roll paper)(Lower)
No roll paper has been fed when a job with
lower roll paper specification is received.
No roll paper available (trailing edge of roll
paper detected)
・Detected that cut sheet sized paper has
been fed at the roll paper feeding slot.
・The trailing edge of paper was detected
by the PE sensor during operation in
which roll paper was used.
・The spool stopped rotating during paper
loading or printing
(XX: Upper roll paper/ Lower roll paper)
2-44
Chapter 2 Indexes by Case
Remedial Action
(★: Reference fault
isolation procedure or
tool)
Load roll paper.
①Select "load a roll"
and follow instruction
on the panel.
②Select "stop
printing," or stop
printing by pressing
stop button.
③Release the release
lever and load the
paper.
Load roll paper.
Load roll paper.
Load roll paper.
Load roll paper.
①Select "load a roll"
and follow instruction
on the panel.
②Select "stop
printing," or stop
printing by pressing
stop button.
③Release the release
lever and load the
③ is only for
(
paper.
800/8000/9000
series.)
Load roll paper.
①Replace the roll
paper
・Check paper sensor
R (IO mode).
②Is the paper fed
successfully
(under a negative
load or any other
influence)?