Mitsubishi Electric A800 Plus Series Function Manual page 34

Pr.
Pr.
group
Acceleration/deceleration time
R342 270
during stall condition
Tension command cushion time
R343 1409
during stall condition
R400 276
Line speed monitoring reference
Winding diameter monitoring
R401 1280
reference
Commanded tension monitoring
R402 1281
reference
R410 430
Dancer tension setting
Dancer tension setting input
R411 364
selection
R412 426
Dancer tension setting bias
R413 427
Dancer tension setting gain
R420 648
Target winding diameter
Winding length detection (lower 4
R421 1264
digits)
Dancer / tension sensor feedback
R422 423
detection level
Allowable deviation from target
R423 621
line speed
Winding length detection (upper 4
R424 1346
digits)
R450 159
DA1 output sign selection
∗5
R500 1284
Taper mode selection
Taper setting analog input
R501 1285
selection
R502 1287
Taper ratio setting
R503 1286
Winding diameter at taper start
Taper ratio setting input filter time
R504 829
constant
R510 1288
Data table winding diameter 1
R511 1289
Data table taper ratio 1
R512 1290
Data table winding diameter 2
R513 1291
Data table taper ratio 2
R514 1292
Data table winding diameter 3
R515 1293
Data table taper ratio 3
R516 1294
Data table winding diameter 4
R517 1295
Data table taper ratio 4
R518 1296
Data table winding diameter 5
R519 1297
Data table taper ratio 5
R530 1410
Motor inertia
R531 1411
Empty reel inertia
R532 1412
Roll width
R533 1413
Material specific gravity
Inertia compensation cushion
R534 1418
time
First acceleration time for inertia
R535 1414
compensation
First deceleration time for inertia
R536 1415
compensation
Second acceleration time for
R537 271
inertia compensation
Second deceleration time for
R538 272
inertia compensation
R539 753
Empty reel inertia (integer)
R540 754
Empty reel inertia (exponent)
Mechanical loss setting
R550 1419
frequency bias
Mechanical loss setting
R551 1420
frequency 1
R552 1421
Mechanical loss 1
Refer
Name to
page
137
137
186
186
186
92
92
92
92
176
176
73, 107
69, 90
176
181
92, 124
92, 124
92, 124
92, 124
124
92, 124
92, 124
92, 124
92, 124
92, 124
92, 124
92, 124
92, 124
92, 124
92, 124
130
130
130
130
130
130
130
130
130
130
130
135
135
135
Parameter list (by function group)
Pr.
Pr.
group
Mechanical loss setting
R553 1422
frequency 2
R554 1423
Mechanical loss 2
Mechanical loss setting
R555 1424
frequency 3
R556 1425
Mechanical loss 3
Mechanical loss setting
R557 1426
frequency 4
R558 1427
Mechanical loss 4
Mechanical loss setting
R559 1428
frequency 5
R560 1429
Mechanical loss 5
R570 620
Line speed bias for reel change
Gear ratio numerator (follower
R600 1243
side)
Gear ratio denominator (driver
R601 1244
side)
E: Environment setting
parameters
Parameters that set the inverter operation characteristics.
Pr.
Pr.
group
Parameter for manufacturer setting. Do not
E000 168
set.
Parameter for manufacturer setting. Do not
E001 169
set.
E020 1006
Clock (year)
E021 1007
Clock (month, day)
E022 1008
Clock (hour, minute)
Parameter for manufacturer setting. Do not
E023 269
set.
Parameter for manufacturer setting. Do not
E080 168
set.
Parameter for manufacturer setting. Do not
E081 169
set.
E100 75
Reset selection
E101 75
Disconnected PU detection
E102 75
PU stop selection
E103 145
PU display language selection
E104 990
PU buzzer control
E105 991
PU contrast adjustment
E106 1048
Display-off waiting time
E107 75
Reset limit
E108 1000
Direct setting selection
E110 1049
USB host reset
Frequency setting/key lock
E200 161
operation selection
Frequency change increment
E201 295
amount setting
E300 30
Regenerative function selection
E301 570
Multiple rating setting
E302 977
Input voltage mode selection
E400 77
Parameter write selection
E410 296
Password lock level
E411 297
Password lock/unlock
Parameter for manufacturer setting. Do not
E415 1499
set.
E420 888
Free parameter 1
E421 889
Free parameter 2
PARAMETER LIST
Refer
Name to
page
135
135
135
135
135
135
135
135
90
161
161
Refer
Name to
page
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
7
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
─
∗6
33
2