Mitsubishi Electric A800 Plus Series Function Manual page 28

Pr.
Pr. Name
group
Speed control integral term
1115 G218
clear time
Constant output range speed
1116 G206
control P gain compensation
Speed control P gain 1 (per-unit
1117 G261
system)
Speed control P gain 2 (per-unit
1118 G361
system)
Model speed control gain (per-
1119 G262
unit system)
Per-unit speed control reference
1121 G260
frequency
Tension sensor feedback
1136 R330
voltage/current bias
1137 R331 Tension sensor feedback bias
Tension sensor feedback
1138 R332
voltage/current gain
1139 R333 Tension sensor feedback gain
1150 A810
to to User parameters 1 to 50
1199 A859
Tension PI gain tuning timeout
1211 R171
time
1215 R172 Limit cycle output upper limit
1217 R173 Limit cycle hysteresis
Tension PI gain tuning start/
1219 R170
status
1222 R175 Target amplitude
Manipulated amount for
1223 R174
operation
Tension PI gain tuning response
1226 R176
level setting
Dancer / tension sensor
1227 R103 feedback input filter time
constant
1230 R002 Winding/unwinding selection
1231 R010 Material thickness d1
1232 R011 Material thickness d2
1233 R012 Material thickness d3
1234 R013 Material thickness d4
1235 R020 Maximum winding diameter 1
1236 R021 Minimum winding diameter 1
1237 R022 Maximum winding diameter 2
1238 R023 Minimum winding diameter 2
1239 R024 Maximum winding diameter 3
1240 R025 Minimum winding diameter 3
1241 R026 Maximum winding diameter 4
1242 R027 Minimum winding diameter 4
Gear ratio numerator (follower
1243 R600
side)
Gear ratio denominator (driver
1244 R601
side)
Sampling time for winding
1245 R042
diameter calculation
Line speed at winding diameter
1246 R040
calculated value activation
Winding diameter change
1247 R000
increment amount limit
Winding diameter change limit
1248 R001
disable time
Number of averaging for
1249 R043
winding diameter calculation
Winding diameter compensation
1250 R260
speed filtering waiting time
Parameter list (by parameter number)
Minimum
Setting range setting
increments
0 to 9998 ms 1 ms
0 to 100% 0.1%
0 to 300, 9999 0.01
0 to 300, 9999 0.01
0 to 300, 9999 0.01
0 to 400 Hz 0.01 Hz
0 to 100% 0.1%
0 to 100N 0.01N
∗13
0 to 100% 0.1%
0 to 100N 0.01N
∗13
0 to 65535 1
1 to 9999 s 1 s
0 to 100% 0.1%
0.1 to 10% 0.1%
1, 8 (0, 2, 3, 9, 12, 13,
1
90 to 96)
0 to 100%, 9999 0.1%
0 to 10% 0.1%
1 to 7 1
0 to 5 s 0.01 s
0, 1 1
0 to 20 mm, 9999 0.001 mm
0 to 20 mm 0.001 mm
0 to 20 mm 0.001 mm
0 to 20 mm 0.001 mm
1 to 6553 mm 1 mm
1 to 6553 mm 1 mm
1 to 6553 mm 1 mm
1 to 6553 mm 1 mm
1 to 6553 mm 1 mm
1 to 6553 mm 1 mm
1 to 6553 mm 1 mm
1 to 6553 mm 1 mm
1 to 65534 1
1 to 65534 1
0.01 to 1 s, 9999 0.01 s
0 to 6553.4 m/min 0.1 m/min
∗11
0 to 9.998 mm, 9999 0.001 mm
0 to 100 s 0.01 s
0 to 10 1
0 to 100 s 0.01 s
Initial value Refer
to
FM CA
page
0 s ─
∗17
0% ─
∗17
9999 ─
∗17
9999 ─
∗17
9999 ─
∗17
120 Hz
∗2
─
∗17
60 Hz
∗3
0% 149
0N 149
∗13
100% 149
100N 149
∗13 ∗13
0 ─
∗17
50 s 76
0% 76
1% 76
0 76
9999 76
1% 76
2 76
71,
0 s 106,
149
59,
0 135,
149
9999 166
1 mm 166
1 mm 166
1 mm 166
2 mm 169
1 mm 169
2 mm 169
1 mm 169
2 mm 169
1 mm 169
2 mm 169
1 mm 169
1 161
1 161
9999 163
1 m/min 167
∗11 ∗11
9999 161
0 s 161
4 168
0 s 170
PARAMETER LIST
Customer
setting
2
27